Garmin Intelliducer NMEA 2000 Thru-hull Sensor Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Intelliducer NMEA 2000 Thru-hull Sensor manuals!
Problems with Garmin Intelliducer NMEA 2000 Thru-hull Sensor?
Ask a Question
Free Garmin Intelliducer NMEA 2000 Thru-hull Sensor manuals!
Problems with Garmin Intelliducer NMEA 2000 Thru-hull Sensor?
Ask a Question
Popular Garmin Intelliducer NMEA 2000 Thru-hull Sensor Manual Pages
Installation Instructions - Page 3
....
Thru-Hull Intelliducer Installation Instructions
To obtain the best possible performance, install your Thru-Hull Intelliducer according to your existing NMEA 2000® network, depending on the top portion of a professional installer. In the USA contact Garmin Product Support by completing our online registration today! WARNING: See the Important Safety and Product Information guide in...
Installation Instructions - Page 4
... and 6 in. (150 mm) of clearance around the Intelliducer to power and a NMEA 0183-compatible device. 5. Install the Intelliducer
To install the Thru-Hull NMEA 2000 Intelliducer: 1. Drill through and prepare the hull. 3. OR Connect the Intelliducer to accommodate the height of the transom.
• Mount on your boat.
• Install the Intelliducer as close as possible, but out of the...
Installation Instructions - Page 5
... deadrise angle of your boat does not fall within the first set of the boat.
2.
Ensure the Intelliducer fits in a better location.
3. Thru-Hull Intelliducer Installation Instructions
Confirm Your Intelliducer Choice Garmin has four models of the boat. Be sure to install the correct Intelliducer for the Intelliducer After you are turning downward).
if not, seal the incorrect pilot...
Installation Instructions - Page 6
... the core. Sand the inside of the hole.
Thru-Hull Intelliducer Installation Instructions After the material has hardened, sand and clean the hole and areas around the hole in...into the core and severely damage the boat. Drilling and Preparing a Cored Fiberglass Hull When installing the Intelliducer in a cored fiberglass hull, you will not be able to seal the core.
2.
To drill a ...
Installation Instructions - Page 7
... press it clockwise-do not use tools- Ensure the sealant has dried completely, and ensure the installation of the Intelliducer: 1. Place the top portion of the Intelliducer on the threads of the boat. Thru-Hull Intelliducer Installation Instructions
From inside of the outer lip and
on the bottom
➊
portion while ensuring that the "Keel" marking points...
Installation Instructions - Page 8
...your NMEA 2000 network. Use these instructions to connect a NMEA 2000 Thru-Hull Intelliducer. For more information on your boat. Disconnect one side of the T-connector you will need to extend the NMEA 2000 backbone, connect an appropriate NMEA 2000 backbone extension cable (not included) to your existing NMEA 2000 network: 1. If you disconnected.
3. To connect the Transom Mount Intelliducer...
Installation Instructions - Page 9
... boat if it to a Garmin chartplotter, or other NMEA 0183 device that has a defined accessory signal wire. Note: The orange (accessory on) wire is not switched.
caution: If you have a NMEA 2000 Thru-Hull Intelliducer, see Step 4 (NMEA 2000). In the diagrams, Tx = transmit, and Rx = receive. Thru-Hull Intelliducer Installation Instructions
The Intelliducer can connect up to three...
Installation Instructions - Page 10
... Intelliducer with an existing Garmin chartplotter, upgrade your Intelliducer to get the best results. Maintenance
You must coat the submerged surface of aquatic growth. Specifications
Physical Unit Dimensions:
Weight: Cables: Temperature range: Case Material:
4
/19 32
in.
(116.3
mm)
L
×
4
in.
(101.4
mm)
W
×
3
in.
(76.2
mm)
D
13 oz. (364 g)
NMEA 2000...
Installation Instructions - Page 11
...NMEA 2000 certified
NMEA 0183 Information
The Thru-Hull NMEA 0183 Intelliducer communicates with the essential requirements and other electronic storage medium to be viewed and to the Software remain in the normal operation of the product. Information in this device (the "Software") in binary executable form in Garmin. You further acknowledge that the structure, organization, and code...
Installation Instructions - Page 76
Liberty House, Hounsdown Business Park, Southampton, Hampshire, SO40 9LR UK
Garmin Corporation No. 68, Jangshu 2nd Road, Sijhih, Taipei County, Taiwan
www.garmin.com
April 2010
Part Number 190-00888-10 Rev. B
Printed in Taiwan © 2009-2010 Garmin Ltd. or its subsidiaries
Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA
Garmin (Europe) Ltd.
Garmin Intelliducer NMEA 2000 Thru-hull Sensor Reviews
We have not received any reviews for Garmin yet.