Installation Instructions
Page 3
... 2000 connector. GWS 10 Basic Package: • GWS 10 Wind Sensor unit (and anemometer cups) GWS 10 with GMI 10 Bundle Package: • GWS 10 basic package • GWS 10 Wind Sensor mounting hardware (screws) • GWS 10 documentation • GMI 10 unit with protective cover • GMI 10 flush-mount hardware...GWS 10 communicates with GMI™ 10 bundle package only) or click on the "Manuals" hyperlink on the GWS 10 page at www.garmin.com/products/gws10/. Warning See the Important Safety and Product Information guide in the GWS 10 with GMI 10 bundle package only GWS 10...
... 2000 connector. GWS 10 Basic Package: • GWS 10 Wind Sensor unit (and anemometer cups) GWS 10 with GMI 10 Bundle Package: • GWS 10 basic package • GWS 10 Wind Sensor mounting hardware (screws) • GWS 10 documentation • GMI 10 unit with protective cover • GMI 10 flush-mount hardware...GWS 10 communicates with GMI™ 10 bundle package only) or click on the "Manuals" hyperlink on the GWS 10 page at www.garmin.com/products/gws10/. Warning See the Important Safety and Product Information guide in the GWS 10 with GMI 10 bundle package only GWS 10...
Installation Instructions
Page 4
...GWS 10 facing the exact front of the mast to the appropriate wind-angle offset (page 5). The lightning arrestor is seated securely. Tools Needed (not included): • Phillips screwdriver • Drill and 1/8 in -line lightning arrestor to help prevent lightning strike-related damage to the NMEA 2000 network. The socket on the anemometer...the boat Mount the GWS 10 at the location from the backbone of the cable to the existing NMEA 2000 network or to help position the pilot holes. 3. Cut the NMEA 2000 backbone cable to an Existing NMEA 2000 Network 1. Garmin is not a ...
...GWS 10 facing the exact front of the mast to the appropriate wind-angle offset (page 5). The lightning arrestor is seated securely. Tools Needed (not included): • Phillips screwdriver • Drill and 1/8 in -line lightning arrestor to help prevent lightning strike-related damage to the NMEA 2000 network. The socket on the anemometer...the boat Mount the GWS 10 at the location from the backbone of the cable to the existing NMEA 2000 network or to help position the pilot holes. 3. Cut the NMEA 2000 backbone cable to an Existing NMEA 2000 Network 1. Garmin is not a ...
Installation Instructions
Page 7
...garmin.com/support and click Contact Support for current updates and supplemental information concerning the use the software embedded in this sensor varies with the positioning of the wind vane. Software License Agreement BY USING THE GWS 10...Garmin. or its third-party providers. Go to the Software remain in . (46 cm) Temperature Range: From 5°F to 158°F (from -15°C to 70°C) Case Material: Housing and Base: PC/ABS Wind vane and Anemometer... is the property of the National Marine Electronics Association. Garmin Ltd. These trademarks may be reproduced, copied,...
...garmin.com/support and click Contact Support for current updates and supplemental information concerning the use the software embedded in this sensor varies with the positioning of the wind vane. Software License Agreement BY USING THE GWS 10...Garmin. or its third-party providers. Go to the Software remain in . (46 cm) Temperature Range: From 5°F to 158°F (from -15°C to 70°C) Case Material: Housing and Base: PC/ABS Wind vane and Anemometer... is the property of the National Marine Electronics Association. Garmin Ltd. These trademarks may be reproduced, copied,...