Installation Instructions
Page 4
... the chartplotter and/or GSD 22 to shut off ) for extended periods of the GSD 22 and turn the locking ring clockwise until it stops. To connect the GSD 22 to your Garmin dealer. Installation Instructions The GSD 22 must be properly installed according to the following sections: GSD 22 Wiring Connection, and Marine Network Wiring and Cables. 5. Connect the power/data and transducer...
... the chartplotter and/or GSD 22 to shut off ) for extended periods of the GSD 22 and turn the locking ring clockwise until it stops. To connect the GSD 22 to your Garmin dealer. Installation Instructions The GSD 22 must be properly installed according to the following sections: GSD 22 Wiring Connection, and Marine Network Wiring and Cables. 5. Connect the power/data and transducer...
Installation Instructions
Page 5
... the installation hole until it around the grommet and cable after installation. Test the connection before installing the grommets. Marine Network Wiring and Cables Garmin Marine Network components use specialized Garmin Network cables. Use a 1¼ in . (32 mm) holes to drill ...the installation hole. 3. Spread the grommet apart at the split, and place it is seated. 7. Wiring instructions are provided to cover the installation holes (see below for the Power/Data, Garmin Marine Network, or GPS 17 Cable Split GSD 22...
... the installation hole until it around the grommet and cable after installation. Test the connection before installing the grommets. Marine Network Wiring and Cables Garmin Marine Network components use specialized Garmin Network cables. Use a 1¼ in . (32 mm) holes to drill ...the installation hole. 3. Spread the grommet apart at the split, and place it is seated. 7. Wiring instructions are provided to cover the installation holes (see below for the Power/Data, Garmin Marine Network, or GPS 17 Cable Split GSD 22...
Installation Instructions
Page 6
... 2000 or NMEA 0183 connections. To transducer GSD 22 sounder xxxxxxxxxx xxxxxxxxxxx The Garmin Marine Network with a Single Chartplotter and a GSD 22 Garmin marine radar Garmin GDL 30/30A marine XM receiver Garmin GMS 10 network port expander xxxxxxxxxx To transducer GSD 22 sounder xxxxxxxxxxx Garmin GPS 17 antenna Serial cable Ethernet cable xxxxxxxxx Transducer cable The Garmin Marine Network with a GSD 22 connected. Wire each device according...
... 2000 or NMEA 0183 connections. To transducer GSD 22 sounder xxxxxxxxxx xxxxxxxxxxx The Garmin Marine Network with a Single Chartplotter and a GSD 22 Garmin marine radar Garmin GDL 30/30A marine XM receiver Garmin GMS 10 network port expander xxxxxxxxxx To transducer GSD 22 sounder xxxxxxxxxxx Garmin GPS 17 antenna Serial cable Ethernet cable xxxxxxxxx Transducer cable The Garmin Marine Network with a GSD 22 connected. Wire each device according...
Installation Instructions
Page 7
...In this code persists, check the wiring. GSD 22 is powered on the GSD 22 to clear the alarm. If the cause is connected and this state, the GSD 22 does not transmit any sonar signals or send any sonar information to a chartplotter. The chartplotter gives... Sonar Sounder Power: 500/1,000/2,000 watts (RMS) (Dependent on transducer type, water salinity, bottom type, and other water conditions.) Data Output Source: Garmin Marine Network GSD 22 Installation Instructions Software failure - After the alarm condition is fixed, power must be cycled on but is waiting to connect to...
...In this code persists, check the wiring. GSD 22 is powered on the GSD 22 to clear the alarm. If the cause is connected and this state, the GSD 22 does not transmit any sonar signals or send any sonar information to a chartplotter. The chartplotter gives... Sonar Sounder Power: 500/1,000/2,000 watts (RMS) (Dependent on transducer type, water salinity, bottom type, and other water conditions.) Data Output Source: Garmin Marine Network GSD 22 Installation Instructions Software failure - After the alarm condition is fixed, power must be cycled on but is waiting to connect to...
