Manual/User Guide
Page 3
...and base) other than parts to Signal Ground (SG). 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). IMPORTANT Use M3 screw for the mounting screw and the screw length... should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. ...
...and base) other than parts to Signal Ground (SG). 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). IMPORTANT Use M3 screw for the mounting screw and the screw length... should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. ...
Manual/User Guide
Page 5
3.2 Mounting IMPORTANT Because of breather C141-E254 3-5 Figure 3.3 Location of breather hole mounted to the HDD, do not allow this to block. Locating of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather hole is shown as Figure 3.3.
3.2 Mounting IMPORTANT Because of breather C141-E254 3-5 Figure 3.3 Location of breather hole mounted to the HDD, do not allow this to block. Locating of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather hole is shown as Figure 3.3.
Manual/User Guide
Page 7
... (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Pressing it by ...external magnetic fields. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. C141-E245 3-7 Static: When handling the device, disconnect the body ground (500 kΩ or...
... (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Pressing it by ...external magnetic fields. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. C141-E245 3-7 Static: When handling the device, disconnect the body ground (500 kΩ or...
Manual/User Guide
Page 8
...on it. Do not stack when carrying. Do not drop. M3 0.49N • m (5 kgf • cm). - Do not hit HDD each other. Installation (1) Please use the driver of the screw strictly. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX... HIOS 3-8 C141-E245 General notes Wrist strap Use the Wrist strap. Figure 3.6 Handling cautions - Do not place HDD vertically to avoid falling down. Installation Conditions - HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when ...
...on it. Do not stack when carrying. Do not drop. M3 0.49N • m (5 kgf • cm). - Do not hit HDD each other. Installation (1) Please use the driver of the screw strictly. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX... HIOS 3-8 C141-E245 General notes Wrist strap Use the Wrist strap. Figure 3.6 Handling cautions - Do not place HDD vertically to avoid falling down. Installation Conditions - HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when ...