Edimax ES-5808PHG Support and Manuals
Get Help and Manuals for this Edimax item
This item is in your list!
View All Support Options Below
Free Edimax ES-5808PHG manuals!
Problems with Edimax ES-5808PHG?
Ask a Question
Free Edimax ES-5808PHG manuals!
Problems with Edimax ES-5808PHG?
Ask a Question
Popular Edimax ES-5808PHG Manual Pages
Datasheet - Page 1
...set up to the PoE network architecture. All of PoE Devices The ES‐5808PHG...Edimax ES‐5808PHG is truly a superb choice to unplug and plug the network line manually.
The ES‐5808PHG...ES‐5808PHG also supports Rapid Spanning Tree to the ES‐5808PHG. Compliant with 8 PSE/PoE ports. It is designed for sturdy network connections in seconds. With the ES‐5808PHG...
Datasheet - Page 2
Specification
Standards
Features
Smart Features
Transmission Media Led Indicators Power Requirement Power ...Method: Store and Forward
VLAN: 16 Trunk Groups : 4 SNMP Quality of Service IGMP Snooping LACP, RSTP Rate Limiting 802.1x Port‐based Security Management: Port Mirroring, Password‐protected Access, Port Settings, Web‐ base Management, Graphic User Interface
10BaseT Cat. 3, 4, ...
Manual - Page 9
...Password successfully entered". Login
Password: 1234
Figure 1-1
After the user login, the right side of website shows all functions as Fig. 1-2.
8 Please follow the description to pass the authentication then clicks the Apply. At the first, open the web browser, and go to set... up and manage the switch through the web user interface. Software Description
This part instructs user how ...
Manual - Page 11
...: Displays the unique hardware address assigned by manufacturer (default).
¾ S/W Version: Displays the switch's firmware version. ¾ H/W Version: Displays the switch's Hardware version. ¾ DHCP Enabled: Click the...password (The default value is
using. The default IP is 192.168.2.1 ¾ Fallback Subnet Mask: Assign the subnet mask to enable DHCP ¾ Fallback IP address: Manually...
Manual - Page 12
...to maintain connection requirements. ¾ Mode: allow user to manually set and view the operation mode for each port. ¾ ...
11 Compared to standard Ethernet frames that acts like a password and permits access to the SNMP database on this switch to...Community: Community string sent with the notification operation. issued by supporting jumbo frames on Gigabit Ethernet ports up to 1.5 KB,...
Manual - Page 14
Up to 16 VLANs based on 802.1Q standard. VLAN 1 is the default untagged VLAN. Figure 1-5-2 13 Figure 1-5-1
VLAN Setup The switch supports up to 16 VLAN groups can create and delete VLANs, and change the VLAN port membership.
devices are still plugged into the same switch physically. ...
Manual - Page 16
...to be bundled together and act as a single physical link for a port, we recommend setting the PVID to "None," all outgoing packets are tagged unless the packet's VLAN ID is ...its component physical links. It provides load balancing, and redundancy of its PVID has been changed to service. A port failure within the trunk in a trunk is maintained whenever a link in a deterministic ...
Manual - Page 17
... have the same priority, the device with the lowest MAC address will automatically be set to the same value as a logical trunk and providing load balancing and fault tolerance... ¾ Key Value: Configures a port's LACP administration key. The port
administrative key must be set to the same link aggregation group (LAG). RSTP System Configuration ¾ System Priority: This parameter ...
Manual - Page 18
... pathcost.
17 Normal -
use . Figure 1-8-1
RSTP Port Configuration ¾ Port: The port ID. Set the RSTP pathcost on the tick-box to enable/disable the RSTP protocol for a BPDU frame. configuration message... values should be changed. Number between 1-10 (default is 15). ¾ Force Version: Set and show the RSTP protocol to ports with STP. It cannot be assigned to ports attached to...
Manual - Page 20
... Querier, which hosts want to receive multicast traffic. ¾ Router Ports: Set if ports are connecting to the switch and multicast routers in the network....on the IGMP conversation between hosts connected to the IGMP administrative routers. ¾ Unregistered IPMC Flooding enabled: Set the forwarding mode for asking hosts if they want to receive the multicast traffic. ¾ IGMP Querying...
Manual - Page 22
... priority queues. ¾ WRR: Weighted Round-Robin shares bandwidth at the egress ports by
using scheduling weights with default values of Service (QoS) In QoS Mode, select QoS Disabled, 802.1p, or DSCP to configure the related parameters. Figure 1-10-2
Quality of 1, 2, 4, 8 for queues 0 through 7, respectively. (This ...
Manual - Page 24
The Differentiated Services Code Point (DSCP) is a six-bit field that is set the values in the range 0 - 63. User can use the Prioritize Traffic drop-down list to quickly set to DSCP, the DSCP Configuration table...header. The six bits allow the DSCP field to the high priority egress queue. The default settings map all DSCP values to take any value in the
23 Figure 1-11-3
Figure 1-11-4...
Manual - Page 30
... this port to shared media. Note that if the switch detects another bridge connected to this port, the manual setting for conflicting information that "steady" state are likely to be overridden, and the port will wait before it...: The cost for reconfiguration is functioning as an edge port, either through ¾ manual selection (see the RSTP Port Configuration table) or auto-detection.
Manual - Page 36
... choose a file location on the web management station. Configuration files can download firmware files for all parameters governing the onboard agent. Use the Browse button to...upgrade the selected switch firmware file. User should therefore assign a new administrator password as soon as possible, and store it in a safe place.
35 Software upload Select "Upgrade Firmware" from the Support...
Edimax ES-5808PHG Reviews
Do you have an experience with the Edimax ES-5808PHG that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Edimax yet.
Earn 750 points for your review!