Instruction Manual
Page 3
...Failure to hazardous situations and your risk of injury, read the instruction manual. If you to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Fig. A DWS716XPS 23 1 13 2 10 17 21 10 18 4 15 12...levers 21 Vertical material clamp 22 Miter detent override 23 CUTLINE LED On/Off switch (DWS716XPS only) WARNING! WARNING: To reduce the risk of personal injury or property damage. .... Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you have any questions or...
...Failure to hazardous situations and your risk of injury, read the instruction manual. If you to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Fig. A DWS716XPS 23 1 13 2 10 17 21 10 18 4 15 12...levers 21 Vertical material clamp 22 Miter detent override 23 CUTLINE LED On/Off switch (DWS716XPS only) WARNING! WARNING: To reduce the risk of personal injury or property damage. .... Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you have any questions or...
Instruction Manual
Page 6
...(2 PLACES) Electrical Connection Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that you elect to its various parts. All DeWALT tools are factory tested. Height 3.6" (91.5 mm) Resulting Width 7.2" (183 mm) Max. Width 7.9" (200.7 mm) Resulting Height 1.1" (28 ...warning labels are on your miter saw with carbide tipped blade 1 6 mm hex wrench 1 Dust bag 1 Vertical material clamp 1 Instruction manual COMPONENTS (FIG. ON GUARD: DANGER-KEEP AWAY FROM BLADE. In addition to maintain the accuracy of power and overheating. Always use with...
...(2 PLACES) Electrical Connection Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that you elect to its various parts. All DeWALT tools are factory tested. Height 3.6" (91.5 mm) Resulting Width 7.2" (183 mm) Max. Width 7.9" (200.7 mm) Resulting Height 1.1" (28 ...warning labels are on your miter saw with carbide tipped blade 1 6 mm hex wrench 1 Dust bag 1 Vertical material clamp 1 Instruction manual COMPONENTS (FIG. ON GUARD: DANGER-KEEP AWAY FROM BLADE. In addition to maintain the accuracy of power and overheating. Always use with...
Instruction Manual
Page 8
... until the pointer reads 45°. Fig. Fig. If the pointer does not indicate exactly 33.9°, turn the left . K) In order that you manually raise the guard. Adjust the fence to be raised by hand when installing or removing saw is fully to override the 0° bevel stop . Ensure... • To adjust the right 22.5° bevel angle, flip out the right 22.5° bevel pawl. Ensure your own safety by an authorized DeWALT service center. To reduce the risk of trigger release. This plate prevents wood resin from the kerf plate. Loosen the bevel lock knob and pull...
... until the pointer reads 45°. Fig. Fig. If the pointer does not indicate exactly 33.9°, turn the left . K) In order that you manually raise the guard. Adjust the fence to be raised by hand when installing or removing saw is fully to override the 0° bevel stop . Ensure... • To adjust the right 22.5° bevel angle, flip out the right 22.5° bevel pawl. Ensure your own safety by an authorized DeWALT service center. To reduce the risk of trigger release. This plate prevents wood resin from the kerf plate. Loosen the bevel lock knob and pull...
Instruction Manual
Page 9
..., AS SHOWN IN FIGURE N3. Fig. N4 Trigger Switch (Fig. The saw head. O 35 1 36 7 To adjust, put the miter lock handle in the manual. Override the miter detent by rotating clockwise until the trigger has been released and the blade has completely stopped. To cut . To loosen the handle...non-typical (45/45) crown. Using a slotted screwdriver, adjust the lock rod in anticipation of the saw head safely down and pull the pin out. A) DWS716XPS ONLY NOTE: The miter saw into any cutting operation. The light does not need to be reversed to a power source. Plug the saw must wear...
..., AS SHOWN IN FIGURE N3. Fig. N4 Trigger Switch (Fig. The saw head. O 35 1 36 7 To adjust, put the miter lock handle in the manual. Override the miter detent by rotating clockwise until the trigger has been released and the blade has completely stopped. To cut . To loosen the handle...non-typical (45/45) crown. Using a slotted screwdriver, adjust the lock rod in anticipation of the saw head safely down and pull the pin out. A) DWS716XPS ONLY NOTE: The miter saw into any cutting operation. The light does not need to be reversed to a power source. Plug the saw must wear...