Dewalt DWE402N Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DWE402N manuals!
Problems with Dewalt DWE402N?
Ask a Question
Free Dewalt DWE402N manuals!
Problems with Dewalt DWE402N?
Ask a Question
Popular Dewalt DWE402N Manual Pages
Instruction Manual - Page 3
...heat, oil, sharp edges or moving parts. e) When operating a power tool ...instruction manual.
Cluttered or dark areas invite accidents. d) Do not abuse the cord.
Read all safety warnings and all instructions...DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). Distractions can cause you to these symbols. c) Do not expose power tools to follow the warnings and instructions...
Instruction Manual - Page 4
...for the connection of dust extraction and collection facilities, ensure these instructions to power source and/ or battery pack, picking up or ... measures reduce the risk of the power tool in a hazardous situation.
5) SERVICE a) Have your finger on . d) Store idle power tools out of the...repair person using only identical replacement parts. g) Use the power tool, accessories and tool bits,...
Instruction Manual - Page 5
... which are not specifically designed and recommended by flanges, the arbor hole of the accessory must be adequately guarded or controlled. Depending...install an undamaged accessory.
The dust mask or respirator must be capable of stopping flying debris generated by various operations. Prolonged exposure to follow all safety warnings, instructions, illustrations and specifications...
Instruction Manual - Page 6
.... x) Air vents often cover moving parts. Abrasive wheels may result in moving parts and should always be detected.
Using ...support the workpiece to provide extra cushion, take frequent rest periods, and limit daily time of time. w) Do not operate this manual... starting the tool with a new or replacement wheel, or a new or replacement wire brush installed, hold the tool in injury.
If ...
Instruction Manual - Page 8
...contains chemicals known to minimize the risk of the wheel. e) Support panels or any interference of the wire wheel or brush with ANSI Z87.1 MUST be placed under their...
a) Do not use of California to spin freely. Additional Safety Information
WARNING: ALWAYS use of a guard is dusty. Never attempt to work and centrifugal forces. Large workpieces tend to the brush. The wire...
Instruction Manual - Page 10
... lock button
K. Spindle
(DWE402, DWE402G)
F. English
Minimum Gauge for Cord Sets
Volts
Total Length of Cord
in Feet (meters)
Ampere Rating 120 V
25...
14
12 Not Recommended
SAVE THESE INSTRUCTIONS FOR FUTURE USE
COMPONENTS (Fig. 1)
WARNING: Never modify the power tool or any part of it. Type 27 Guard (4-1/2" / 115mm)
C.
Guard release lever
D. Threaded locking flange
...
Instruction Manual - Page 11
... motor housing FIG. 2
become separated by more than 1/8"
(3.17 mm), the tool must always be serviced and
re-assembled by a DEWALT service center. An accidental start-up can be rated for a circular saw. These heavy-duty small angle grinders are factory tested;
Voltage decrease of more than 10% will rotate 90° for information on...
Instruction Manual - Page 12
..., ADJUSTING AND REMOVING (TYPE 27) ONE-TOUCH™ GUARD (FIG. 3)
Your grinder is supplied with all grinding wheels, cutting wheels, sanding flap discs, wire brushes, and...or authorized service center. A Type 1 guard must be used with a keyless ONE TOUCH™ guard.
1.
Keeping the guard release lever open , align the lugs (L) on the gear case hub. A Type 1 guard (intended ...
Instruction Manual - Page 13
... used for
11
removal of these instructions in the clockwise direction. To remove the guard, follow steps 1-3 of the guard. non-hubbed sanding flap disc
threaded locking flange
4. With the spindle facing the operator, rotate the guard clockwise into one of the alignment holes (N) on the guard collar. NOTE: The guard release lever should be positioned...
Instruction Manual - Page 14
... speed before
making any adjustments or
removing/installing attachments or
accessories. Allow the grinder to run while the switch is A
... to ensure that the switch is locked on the rear most part of the switch.
If the switch is off position as the... pressing on when the power is important to choose the correct guards and flanges to the tool, such as described above after any...
Instruction Manual - Page 15
...reduce the risk of damage to stop. Install the unthreaded backing flange FIG. 8
(G) on button (K) offers FIG. 6 increased comfort in extended use the correct guard per the instructions in this manual
for more information.
1. G
E
13... tool is
D
turned off possibly resulting in continuous mode, press the rear part of the backing flange. To engage the lock, depress the spindle lock button...
Instruction Manual - Page 20
...service center. Abrasive cutting wheels for more information.
Your grinder is off. With the spindle facing the operator,
rotate the guard clockwise into one of these instructions in
reverse.
18
NOTE: The guard release lever should be used. To remove the guard... the tool off and unplug the tool before setting it down until
the guard lugs engage and rotate
them in a forward ...
Instruction Manual - Page 21
... work surface, allowing tool to stop rotating before making repairs. Changing the angle will be used in locating any part of serious personal injury, turn unit off and disconnect ...authorized service center. Recommended accessories for use edge grinding/cutting wheels for side injury, only DEWALT recommended accessories should be against the wheel when the wheel is installed.
...
Instruction Manual - Page 22
... illegible or are not completely satisfied with a receipt for :
• WARRANTY SERVICE: Registering your product will maintain the tool and replace worn parts caused by others. Register online at www.dewalt.com/register. For further detail of purchase. This warranty gives you specific legal rights and you can return it within 90 days from the...
Instruction Manual - Page 72
N382909
DWE402, DWE402N, DWE402G, DWE4214 Copyright © 2014 DEWALT
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the array
of the tool. DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(SEP14)
Part No. the kit box configuration; and the array of lozenge-shaped humps...
Dewalt DWE402N Reviews
We have not received any reviews for Dewalt yet.