Dewalt DW840 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DW840 manuals!
Problems with Dewalt DW840?
Ask a Question
Free Dewalt DW840 manuals!
Problems with Dewalt DW840?
Ask a Question
Dewalt DW840 Videos
Polizor unghiular DeWALT DW840, 1800 W, 8000 RPM, 180 mm
Duration: :26
Total Views: 42
Duration: :26
Total Views: 42
Popular Dewalt DW840 Manual Pages
Instruction Manual - Page 3
...
for Cord Sets
Volts Total Length...codes and ordinances. Applicable only to rain or wet conditions. Never use the next heavier gage. Read and understand all instructions listed... Applicable to install a polarized outlet. Replace damaged cords
...DEWALT TOOL, CALL US TOLL FREE AT:
1-800-4-DEWALT (1-800-433-9258)
General Safety Instructions... moving parts. SAVE THESE INSTRUCTIONS
WORK AREA...
Instruction Manual - Page 4
...
Contain long hair. Keep proper footing and balance at the rate for Grinders
• Do not force tool.
Do not use only identical replacement parts. Use of unauthorized parts or failure to follow maintenance instructions may result in the Maintenance section of this manual.
Follow instructions in personal injury. • Do not overreach. PERSONAL SAFETY
•...
Instruction Manual - Page 5
... from face and
• Always use .
• Do not operate this type of the tool at all times. If the wheel has an undetected crack or flaw, it ...into a corner because a sudden, sharp movement of the grinder may contribute to maintain control of work with a new or replacement wheel, a new or replacement wire brush installed, or if you think the tool may be detected. ...
Instruction Manual - Page 6
... circular saw. See pages 5-6 for continuous use with grinder accessories. Every unthreaded accessory must be locked on for...may result. To turn the tool off , release the switch. Guard (Type 27, open
beneath wheel or accessory)
C
B
E
DA
...or installing attachments or accessories. Before reconnecting the tool, depress and release the rear part of this manual.
CAUTION...
Instruction Manual - Page 7
English
5" Grinding Wheels (DW831)
Type 27 guard unthreaded backing flange Type 27 depressed center wheel
threaded clamp nut
7" Grinding Wheels (DW840)
Type 27 guard backing flange Type 27 non-hubbed wheel
clamp nut
Type 27 guard Type 27 hubbed wheel
Type 27 guard
Type 27 hubbed wheel 5
Instruction Manual - Page 8
... guard
Type 27 guard
rubber backing pad
3" wire cup brush Type 27 guard
unthreaded backing flange
hubbed sanding flap disc
non-hubbed sanding flap disc
threaded clamp nut
4" wire wheel
CAUTION: Use a Type 27 guard with conventional sanding discs and backing pads due to mismatched rated speeds. Operators and others in use.
6
sanding disc
threaded clamp nut WARNING: DW840...
Instruction Manual - Page 9
... pressures encountered with surface grinding. dust. Position yourself so that the open side of the guard must be positioned away from the work surface before touching the tool to the work surface....deep grinding.
Sanding or wire brushing lead based paint is to children and
3. English
Grinding
Using a depressed center Type 27 wheel, hold the tool
so that an angle of 10° to ...
Instruction Manual - Page 10
...replaced daily or whenever the wearer has difficulty breathing. CAUTION: Unplug the tool before being used again. The tool may be sealed with
2. Before reconnecting the tool, depress and release the rear part of 4 mils thickness.
3. CAUTION: Do not operate grinder with a loose guard...this protection. Guards must be used by all grinding wheels and sanding flap discs, wire brushes and wire...
Instruction Manual - Page 11
...
use, perform the following adjustment. Fitting and Removing the Guard DW840 (Fig. 3)
CAUTION: Unplug the tool before mounting or removing the guard.
Undetectable damage to the guard or the mounting hub may result.
REMOVING GUARD 1. Undetectable damage to ensure that the tool is off. Place the angle grinder on the gear case. 2.
Lift up . 2.
Wheels and other...
Instruction Manual - Page 12
... of purchase. Repairs
CAUTION: Never use with the supplied spanner wrench (Fig. 7). CAUTION: Wear work gloves when handling wire cup brushes.
Lubrication
Three Year Limited Warranty
DEWALT tools are ready DEWALT will automatically stop and prevent damage to faulty matefor use identical replacement parts. Tools should only be performed by DEWALT authorized service centers. months...
Instruction Manual - Page 13
... warranty gives you specific legal rights and you can return it within 90 days from the date of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT for free, any reason, you may have been made or attempted by normal use, for a free replacement.
11 FREE WARNING LABEL REPLACEMENT: If your...
Instruction Manual - Page 39
... Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT04) Form No. 392424-02 DW831, 840
Copyright © 2003, 2004 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the kit box configuration; the "D" shaped air intake grill; and the array of the tool...
Dewalt DW840 Reviews
We have not received any reviews for Dewalt yet.