Dewalt DW744X Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DW744X manuals!
Problems with Dewalt DW744X?
Ask a Question
Free Dewalt DW744X manuals!
Problems with Dewalt DW744X?
Ask a Question
Most Recent Dewalt DW744X Questions
My Dw744 Table Saw I Purchased Oct. 2012 Arbature?/?? No Longer Made????
I received a csll from the service center letting me know it was not repairable do to the arborture?...
I received a csll from the service center letting me know it was not repairable do to the arborture?...
(Posted by Islandhr 7 years ago)
Dewalt DW744X Videos
DEWALT DW744X .wmv
Duration: :50
Total Views: 1,708
Duration: :50
Total Views: 1,708
DEWALT DW744X 10 Inch Table Saw, one year later...
Duration: 4:29
Total Views: 98,823
Duration: 4:29
Total Views: 98,823
Popular Dewalt DW744X Manual Pages
Instruction Manual - Page 2
...DEWALT
Built Jobsite Tough...WE GUARANTEE IT.
The design of rigorous use
on jobsites and throughout industry. Every tool is produced with painstak-
Each tool is checked before it meets your standards for America's tough- SEE MANUAL • ALWAYS SUPPORT WORK WITH TABLE...: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW • ALWAYS WEAR EYE PROTECTION ...
Instruction Manual - Page 3
...If repair or replacement of the electric cord or plug is not permitted by the Canadian Electric Code. Use only three-wire extension cords that have three-prong grounding type plugs... Repair or replace damaged or worn cord immediately. B if a properly grounded outlet is properly installed and grounded in accordance with a qualified electrician or service personnel if the grounding instructions are...
Instruction Manual - Page 4
... -up of injury to inflict severe injury. Consult the instruction manual for lubricating and changing accessories. MINIMUM GAGE FOR CORD SETS
Volts Total Length of balance
may result in personal injury.
• USE PROPER EXTENSION CORD. A guard or other part that is sufficient to persons.
• NEVER STAND ON TOOL. Don't force tool or attachment to...
Instruction Manual - Page 5
...: THE FOLLOWING TERMS WILL BE USED THROUGHOUT THE MANUAL AND YOU SHOULD BECOME FAMILIAR WITH THEM.
• Through-sawing refers to any part of your supervisor, instructor, or another qualified person if you must be performed. A length of 12" (305 mm) is needed to have special instructions for cracks or missing teeth. Be certain...
Instruction Manual - Page 6
... how often you read and understand the entire instruction
manual. Cut Depth 0° Bevel 3 1/8" (79mm)
Max. Open the box and slide the saw and its various parts. Carefully unpack the table saw and all the loose items and hardware packed with the saw out, as those dust masks that parts have not been damaged during shipping. Throat plate...
Instruction Manual - Page 7
... to its maximum height by turning counterclockwise. 3. Place the saw arbor by turning the blade height adjustment wheel clockwise. 2. ATTACHING/REPLACING THE BLADE 1. Align the pin with the slot and align the latch with your table saw ASSEMBLING THE RIP FENCE The rip fence can be installed on fence rails, as shown in place. Rip fence (NOTE...
Instruction Manual - Page 8
... functioning. WARNING: Before connecting the table saw to the power
source or operating the saw, always inspect the guard and splitter for precision alignment of the blade. When properly aligned, the splitter will be in Figure...be in Figure 11B. Set the blade at the top of serious personal injury,
the throat plate must be bent until it lines up the parts with the splitter as shown...
Instruction Manual - Page 9
... to the bottom of the saw table. The table saw to adjust your power supply agrees with both the DW744 and the DW744X. Alternately, to enhance the saw's portability, it can be used to shipping and handling or any adjustments. The DEWALT DW7440 Table Saw Stand and the DW7440RS Rolling Stand are provided in . Center the saw is equipped with glue, or...
Instruction Manual - Page 10
... the bracket until it will require calibration for alignment. Place a square flat against the table top and against the square. 5. Check the...(Fig. 19) and move side-to be out of your saw , tighten the nut shown in Figure 20. To realign the.... (8.1 to Miter Slot)
WARNING: Cut Hazard.
BLADE ALIGNMENT ADJUSTMENT (Blade Parallel to 10.8 Nm). Ensure the bevel lock lever is parallel to...
Instruction Manual - Page 11
...set-ups or when making repairs. Turn the saw blade. Using a narrow blade screw driver or #20 torx driver, access the screw through the material. There are two basic types...
The center hole to do specific and special jobs such as cardboard between the ...or operating the saw to provide a guide for proper operation alignment and clearance with table saws: ripping and crosscutting...
Instruction Manual - Page 12
... that the blade is set to speed.
5.
See proper hand position in the desired slot.
2.
WARNING: Before connecting the table saw to saw table. CAUTION: When using both hands away from the blade and away from saw blade to the power source or operating the saw, always inspect the guard and splitter for proper alignment and clearance with...
Instruction Manual - Page 13
... off and disconnect machine from power source before installing and removing accessories, before re-setting the circuit breaker and continuing to place the guard and standard throat plate back in Figure 10 and remove the guard assembly. Never let any part of bevel crosscutting and mitering.Follow the instructions for a cabinet, bookcase or some such project...
Instruction Manual - Page 14
... If you may have other qualified service personnel. Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use identical replacement parts.
English
FIG. 29
HEIGHT ADJUSTMENT
THREADS
where repairs have been made or attempted by a DEWALT factory service center, a DEWALT authorized service center or other rights which vary...
Parts Diagram - Page 2
... List for current parts information.
Page 1 Please visit www.dewaltservicenet.com for DW744X Type 5
Description
Qty Required
TABLE
1
SCREW,TAPTITE
5
TELESC RAIL ASM
2
BRG ASY,PINION
2
SHAFT
1
PINION
1
KNOB
1
SCALE
1
LOCK ARM
1
LINK
1
LINK,THREADED
1
LOCK PIN
2
PLATE
1
SCREW
2
WASHER,BELLEVIL
6
SCREW,M6X20
10
SCREW
2
NUT,STOP
1
WASHER
2
NUT,STOP...
Parts Diagram - Page 6
... for current parts information. Please visit www.dewaltservicenet.com for DW744X Type 5
Description
Qty Required
NUT,LOCK
10
SWITCH ENCLSR.
1
SCREW
1
CORD/10FT/14-2SJ
1
TERMINAL,FEMALE
2
GUARD ASSEMBLY
1
MITER GAUGE
1
THROAT PLTE ASM
1
PUSH STICK
1
FENCE ASSEMBLY
1
SCREW
3
SUPPORT,FRONT
1
SUPPORT,FRONT
1
SUPPORT,REAR
1
SUPPORT,REAR
1
SUPPORT,WORK
1
SCREW...
Dewalt DW744X Reviews
We have not received any reviews for Dewalt yet.