Instruction Manual
Page 1
E ES F PT Self-Leveling 360o Horizontal, Cross Line Laser DW03601, DW03601CG 360º www.DEWALT.com Please read these instructions before operating the product.
E ES F PT Self-Leveling 360o Horizontal, Cross Line Laser DW03601, DW03601CG 360º www.DEWALT.com Please read these instructions before operating the product.
Instruction Manual
Page 7
... about this manual may result in hazardous radiation exposure. Use of controls or adjustments, or performance of procedures, other than those specified herein may result in serious personal injury. Contents • Laser Information • User Safety • Battery Safety • Powering the Laser • Turning the Laser On • Checking Laser Accuracy • Using the Laser • Maintenance • Troubleshooting • Service and Repairs • Specifications Laser Information The DW03601 and DW03601CG...
... about this manual may result in hazardous radiation exposure. Use of controls or adjustments, or performance of procedures, other than those specified herein may result in serious personal injury. Contents • Laser Information • User Safety • Battery Safety • Powering the Laser • Turning the Laser On • Checking Laser Accuracy • Using the Laser • Maintenance • Troubleshooting • Service and Repairs • Specifications Laser Information The DW03601 and DW03601CG...
Instruction Manual
Page 8
... 's eyes. Do not use common sense Load new AA batteries in use the laser if the Power/Transport Lock switch dust or fumes. Any tool that cannot be performed by qualified repair personnel. To locate your nearest DEWALT service center go to follow all batteries at the same time with the switch is not in the DW03601 or DW03601CG laser. Service or maintenance performed by unqualified Maintenance instructions may inadvertently expose...
... 's eyes. Do not use common sense Load new AA batteries in use the laser if the Power/Transport Lock switch dust or fumes. Any tool that cannot be performed by qualified repair personnel. To locate your nearest DEWALT service center go to follow all batteries at the same time with the switch is not in the DW03601 or DW03601CG laser. Service or maintenance performed by unqualified Maintenance instructions may inadvertently expose...
Instruction Manual
Page 9
... the Power/Transport Lock switch to the left to keep the Power/Transport Lock switch in case the laser was exposed to save battery power. Measure the vertical distance between b and c . • This is the first time you perform an accuracy check prior to using the laser (in a while. 8. If your work. USING THE LASER for the corresponding Distance Between a and b in E place (Figure B 4 ). Directly above...
... the Power/Transport Lock switch to the left to keep the Power/Transport Lock switch in case the laser was exposed to save battery power. Measure the vertical distance between b and c . • This is the first time you perform an accuracy check prior to using the laser (in a while. 8. If your work. USING THE LASER for the corresponding Distance Between a and b in E place (Figure B 4 ). Directly above...
Instruction Manual
Page 10
...corresponding Height D in the following table, the laser must be used . 4. Place the laser at least 30′ (9m) long. Move the Power/Transport Lock switch to the right (Figure A 3 ) to conduct 2. of the applications for which the tool will be serviced at the factory to the ...height available, ideally 30′ (9m), with one person on • Extreme temperature changes may cause movement of the same wall and parallel to conduct calibrated. No manual adjustments are required. • Use the laser on a flat surface within average ± 4° of the wall (Figure E ...
...corresponding Height D in the following table, the laser must be used . 4. Place the laser at least 30′ (9m) long. Move the Power/Transport Lock switch to the right (Figure A 3 ) to conduct 2. of the applications for which the tool will be serviced at the factory to the ...height available, ideally 30′ (9m), with one person on • Extreme temperature changes may cause movement of the same wall and parallel to conduct calibrated. No manual adjustments are required. • Use the laser on a flat surface within average ± 4° of the wall (Figure E ...
Instruction Manual
Page 11
... extra cost from a nail or screw on a stable surface. not turn off. • When the laser is not in use, clean the exterior parts with a damp cloth, wipe the laser with a soft dry cloth to make sure: • Each battery is installed correctly, according to (+) and (-) Using the Laser with Accessories listed inside the battery compartment. accessories. Turning the Laser Off Maintenance E Slide the Power/Transport Lock switch to the OFF position...
... extra cost from a nail or screw on a stable surface. not turn off. • When the laser is not in use, clean the exterior parts with a damp cloth, wipe the laser with a soft dry cloth to make sure: • Each battery is installed correctly, according to (+) and (-) Using the Laser with Accessories listed inside the battery compartment. accessories. Turning the Laser Off Maintenance E Slide the Power/Transport Lock switch to the OFF position...
Instruction Manual
Page 12
... not stop moving, try to an average of 4° in a risk of injury. Specifications Light Source Laser Wavelength Laser Power Working Range Accuracy Power Source Operating Temperature Storage Temperature Environmental DW03601 DW03601CG Laser diodes 630 - 680 nm visible 510 - 530 nm visible ≤3.2 mW CLASS 2 LASER PRODUCT 33′ (10m) 50′ (15m) ±0.16" @ 33′ (±4 mm @ 10m) 4 AA (1.5V) size batteries...
... not stop moving, try to an average of 4° in a risk of injury. Specifications Light Source Laser Wavelength Laser Power Working Range Accuracy Power Source Operating Temperature Storage Temperature Environmental DW03601 DW03601CG Laser diodes 630 - 680 nm visible 510 - 530 nm visible ≤3.2 mW CLASS 2 LASER PRODUCT 33′ (10m) 50′ (15m) ±0.16" @ 33′ (±4 mm @ 10m) 4 AA (1.5V) size batteries...