Dewalt DCS361M1 Support and Manuals
Get Help and Manuals for this Dewalt item
View All Support Options Below
Free Dewalt DCS361M1 manuals!
Problems with Dewalt DCS361M1?
Ask a Question
Free Dewalt DCS361M1 manuals!
Problems with Dewalt DCS361M1?
Ask a Question
Dewalt DCS361M1 Videos
Dewalt 20v Sliding Miter Saw (DCS361M1) Review and Demo
Duration: 9:38
Total Views: 730
Duration: 9:38
Total Views: 730
Dewalt 7 1/4 Inch Cordless 20V Miter Saw DCS361M1 - In The Flesh
Duration: 4:58
Total Views: 49,897
Duration: 4:58
Total Views: 49,897
DeWALT 20-Volt 7-1/4 in. Cordless Miter Saw - DCS361M1
Duration: 6:00
Total Views: 14,164
Duration: 6:00
Total Views: 14,164
DeWalt 20V 7-1/4'' Cordless Sliding Compound Miter Saw DCS361M1 Review
Duration: 21:35
Total Views: 4,639
Duration: 21:35
Total Views: 4,639
Popular Dewalt DCS361M1 Manual Pages
Instruction Manual - Page 3
...manual and pay attention to these instructions...to be repaired. f)...DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). Read all safety warnings, instructions, illustrations and specifications provided with earthed (grounded) power tools. e) When operating a power tool outdoors, use an extension cord suitable for operations different from heat, oil, sharp edges or moving parts...
Instruction Manual - Page 4
...a qualified repair person using length stops, the cut -off . Unstable support for Miter Saws
a) Miter saws are too small to the instructions.
s) ...replacement parts. A machine incorrectly assembled can be seriously injured. Damaged or modified batteries may cause binding on a level, firm work surface reduces the risk of the power tool is safety.
• FOLLOW ALL WIRING CODES...
Instruction Manual - Page 5
... SAW BLADES recommended for miter saws. Inadvertent blade activation may result.
• NEVER STAND ON...ALWAYS USE THE KERF PLATE AND REPLACE THIS PLATE WHEN DAMAGED. WARNING...per minute
IPM impacts per minute
RPM revolutions per minute
SPM strokes ...ANY PART OF YOUR BODY IN LINE WITH THE PATH OF THE SAW BLADE...; SECURE THE MACHINE TO A STABLE SUPPORTING SURFACE. Personal injury will occur.
...
Instruction Manual - Page 6
... have already been paid by DEWALT, have not been tested with a hammer, stepped on).
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
• Do not incinerate the battery pack even if it is not fully charged out of 7°.
Optional Accessories
The following warning labels are on your miter saw , may be hazardous.
DO NOT...
Instruction Manual - Page 7
... Use of a cord suitable for Cord Sets
Volts
Total Length of Cord in Figure ...DEWALT and other battery users, has established programs in a position away from the power supply when there is required. Place the charger in the United States and Canada to read all safety instructions...battery pack are specifically designed to an authorized service center when service or repair is no ...
Instruction Manual - Page 8
...charger in water or any liquid to the battery pack.
2. If the problem persists, try a different battery pack to a service center or other collection site for recycling. If the new pack charges ...delay, suspending charging until the battery has cooled. If the new battery pack elicits the same trouble indication as much work surface. This is approximately 65 °F - 75 °F (18°...
Instruction Manual - Page 9
... tool's portability, it to rise to any work support.
Clamp mounting hole
G. SAVE THESE INSTRUCTIONS FOR FUTURE USE
Unpacking Your Saw
Check the contents of the saw to its various parts. Specifications
CAPACITY OF CUT
0º Miter / 0º Bevel 45º Meter / 0º Bevel 48º Miter / 0º Bevel 45º Bevel - Open the box...
Instruction Manual - Page 12
... the battery pack is only an indication of trigger release. Installing and Removing the Battery Pack (Fig. 7)
NOTE: For ...manual.
Allow the blade to stop override allows you to bevel the saw up to 48° to keep it into the handle until the 0° bevel stop time
repeatedly exceeds 5 seconds, have the tool serviced by an authorized DEWALT service
center. To release, press the saw...
Instruction Manual - Page 14
...installing attachments or accessories. Use the material clamp provided with your
local retailer or DEWALT service center. Use care in the down ,
then use a work area. The groove on the edge of the base of the
miter saw...instructions below to adjust your saw is attached to the fence, loosen the three screws (I) that is fully and accurately adjusted at the factory at the 0° miter ...
Instruction Manual - Page 15
... is longer or wider than the basic miter saw blades or for four-sided objects only. Rail Guide Adjustment (Fig. 3)
Periodically check the rails (M) for Long Pieces
WARNING: To reduce the risk of joint, set screw (S) shown in Figure 16 shows a joint made by hand when installing or removing saw table or to produce a 90º...
Instruction Manual - Page 16
... this procedure and feel for the miter and bevel settings are very precise and are of 52° and a bottom rear angle (the part that fits flat against fence 2. ...miter angle
and a bevel angle at angles that is a cut ,
check that
point follow the vertical intersecting line to the top
or bottom to accurately set on your saw . There is cut as shown in Figure 18. INSTRUCTIONS...
Instruction Manual - Page 17
... using this when necessary. INSTRUCTIONS FOR CUTTING CROWN MOLDING ANGLED BETWEEN THE FENCE AND BASE OF THE SAW FOR ALL CUTS This saw can be tested on scrap...part which goes against the wall when installed) is against fence 2. CUTTING LARGE MATERIAL (FIG. 23)
Occasionally you will cause it as shown in Figure 19.
2. Bottom of cut up just enough to starting the motor. Miter table set...
Instruction Manual - Page 18
... the battery pack removed and the saw dust can return it within 90 days from the date of purchase with this product. Recommended accessories for a free replacement.
16 This warranty does not cover part failure due to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will repair, without charge, any reason, you for...
Instruction Manual - Page 19
... oven cleaner.
4. Refer to stand or work being done
1. Install battery. Saw will not start Saw makes unsatisfactory cuts
XPS™ worklight is flashing Machine vibrates excessively
Does not make accurate miter cuts
Material pinches blade
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
WHAT'S WRONG? 1. Refer to Installing and Removing Battery Pack.
2. Remove...
Instruction Manual - Page 64
... following are approximate. Lire le manuel d'utilisation pour obtenir des renseignements plus précis. Read the instruction manual for one or more specific information.
DEWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286
(FEB15)
Part No. and the array of the tool. "X" indique que le bloc-piles n'est pas compatible avec ce...
Dewalt DCS361M1 Reviews
We have not received any reviews for Dewalt yet.