Dewalt D28402K Support and Manuals
Get Help and Manuals for this Dewalt item
This item is in your list!
View All Support Options Below
Free Dewalt D28402K manuals!
Problems with Dewalt D28402K?
Ask a Question
Free Dewalt D28402K manuals!
Problems with Dewalt D28402K?
Ask a Question
Popular Dewalt D28402K Manual Pages
Instruction Manual - Page 2
...instructions listed...installed...low...Sets...parts. SAVE THESE INSTRUCTIONS...
WORK AREA • Keep your product will fit in
doubt, use an outdoor
extension cord marked "W-A" or "W." Power tools create sparks which may result in any way. Applicable only to
carry the current your work area clean and well lit. Read and understand all codes...Not Recommended
1 Replace damaged cords
...
Instruction Manual - Page 3
... the manufacturer for your model. Do not use common sense when operating a power tool. Do not wear loose clothing or jewelry. Loose clothing, jewelry, or long hair can be performed only by qualified repair personnel. TOOL USE AND CARE
• Use clamps or other untrained persons. Additional Specific Safety Instructions for Grinders
• Check that...
Instruction Manual - Page 4
... proper guard with... listed minimum...Type 11 (flaring cup) wheels on your tool often, especially after heavy use side handle. The side handle should burst in a well protected area and let it should always be hazardous. Contact with a new or replacement wheel, or a new or replacement wire brush installed...manual is a sudden reaction to a pinched, bound or misaligned wheel, wire brush...hands...
Instruction Manual - Page 5
... the unit and position your body and arm to allow you do this type of work or pull the unit backward while the wheel is restarted.
• Support large panels to cause cancer, birth defects, or other reproductive harm. Support must be experienced when the wheel or other accessory contacts a secondary surface or...
Instruction Manual - Page 6
...lbs. Remove guard and flanges from motor
housing not more than 1/4", rotate the
gear case head to have the tool serviced may cause brush, motor and bearing failure.
3. English
FIG. 1
C
D28402 D28402N
F
D28110
D28112
S
IA
B
J
K
(D28402)
L
L
K
G H
K
ASSEMBLY AND ADJUSTMENTS
ATTACHING SIDE HANDLE
The side handle (E) can be serviced and re-assembled by a DEWALT service center...
Instruction Manual - Page 7
...with tool. Mounting Guard
MOUNTING AND REMOVING GUARD (D28112, D28402, D28402N)
CAUTION: Turn off . Threaded accessories must be above listed minimum wheel speed as shown on tool nameplate. 4-1/2" Grinding Wheels
Wire Wheels
English
Type 27 guard
Type 27 guard
Type 27 guard
Type 27 guard
backing flange
Type 27 hubbed wheel
3" wire cup brush
4" wire wheel
Type 27 depressed center...
Instruction Manual - Page 8
... pull up on the gear case. To remove the guard, open position.
5. Do not operate the grinder with clamp lever in the groove on the gear case.
2.
The guard body should not be posi- I ) into the desired working po
sition. 4-1/2" Cutting Wheels
Sanding Discs
4-1/2" Sanding Flap Discs
English
Type 1 guard backing flange
Type 1 guard backing flange
abrasive cutting wheel...
Instruction Manual - Page 9
... the side handle and body of the tool firmly to repair or replace the guard. Push the guard down . B
WARNING: Do not disable the lock-off while under load conditions. The tool will start up and during use tool and take the tool and guard to a service center to maintain control of a circuit breaker, accidental
unplugging...
Instruction Manual - Page 10
...grinder by pressing the rear part...installing or removing wheels.
ing the tool off . Before reconnecting the tool, depress and release the paddle switch to ensure that the tool is off.
9 Depress the spindle lock button and use applications.
LOCK-ON BUTTON (D28402)
The lock-on button (J) offers increased
comfort in continuous mode, press the rear
part... flange by hand.
3. Mounting...
Instruction Manual - Page 11
... of the guard must be positioned away from your local dealer or authorized service center.
1....clamp nut
against the wheel, it down. Type 1 guards are installing is 1/8" (3.31mm) thick or less, ...installing is
installed with the raised section
(pilot) against the wheel.
4. If a thin wheel is
more information.
1.
tion (pilot) of this manual for more information. Install...
Instruction Manual - Page 13
... surface. Allowing the tool to stop rotating before making any adjustments or removing or installing attachments or accessories. CAUTION: Use extra care when working over an edge, as previously described to
operate at high speed.
3. The san- A Type 27 guard is greatest when
the tool operates at high speed.
Thread the wheel on...
Instruction Manual - Page 14
... or removing or installing attachments or acces-
MOUNTING CLOSED (TYPE 1) GUARD
CAUTION: Turn off .
1. If rotation is required when using cutting wheels. To remove the guard, open position.
5. CAUTION: Do not tighten adjusting screw with the
slots (O) on the backing flange will be
unable to rotate the guard by hand when
the latch is installed.
2. Undetectable damage...
Instruction Manual - Page 15
...clean the tool before setting it down.
ALWAYS ...service center, a DEWALT authorized service center or other harsh chemicals for cleaning the non-metallic parts of conductive particles. Remove the tool from the accumulation of the tool. If the tool is established in locating any defects due to bend and may result.
1. If you may have been made or attempted by others. Repairs...
Instruction Manual - Page 16
... a free replacement.
15 LATIN AMERICA: This warranty does not apply to the warranty, DEWALT tools are covered by our: 1 YEAR FREE SERVICE
DEWALT will maintain the tool and replace worn parts caused by ...packaging, call 1-800-4-DEWALT for a full refund - English
In addition to products sold in Latin America, see country specific warranty information contained either in Latin America.
Instruction Manual - Page 52
...surface of lozenge-shaped humps on the handgrip; and the array of the tool. Especificaciones
D28402, D28402N
Tensión de alimentación:
120 V AC/DC (
)
Consumo de ...DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (MAR06) Form No. 641881-00 D28110, D28112, D28402, D28402N Copyright © 2005, 2006 DEWALT
The following are trademarks for one or more DEWALT...
Dewalt D28402K Reviews
Do you have an experience with the Dewalt D28402K that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Dewalt yet.
Earn 750 points for your review!