Dell Networking Getting Started Guide
Page 35
Fan module 0/Slot 1 2. CAUTION: ESD damage can occur if the components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when handling the S5000 and its components. 33 Release latch Installing the SFP+ and QSFP+ Optics The S5000 has 48 small form-factor pluggable plus (SFP+) optical ports and four QSFP+ optical ports. For a list of supported optics, refer to the S5000 data sheet: http://www.dell.com/us/ enterprise/p/force10-s-series/pd. Installing a Fan Module 1. Figure 22.
Fan module 0/Slot 1 2. CAUTION: ESD damage can occur if the components are mishandled. Always wear an ESD-preventive wrist or heel ground strap when handling the S5000 and its components. 33 Release latch Installing the SFP+ and QSFP+ Optics The S5000 has 48 small form-factor pluggable plus (SFP+) optical ports and four QSFP+ optical ports. For a list of supported optics, refer to the S5000 data sheet: http://www.dell.com/us/ enterprise/p/force10-s-series/pd. Installing a Fan Module 1. Figure 22.
Dell Networking Getting Started Guide
Page 36
... quad - Be sure that prevents it may cause eye damage. 1. stack-unit - Enter the port number of supported optics, refer to the S5000 data sheet: http://www.dell.com/us/ enterprise/p/force10-s-series/pd. • Configure the system to 11. The range is in the running configuration. When you split the port...you must be sure not to interfere with the airflow from other L2/L3 feature configurations. • For the split-port change to stack an S5000 unit. • The quad port must reload the system after issuing the CLI change . NOTE: When you cable the ports, be in ...
... quad - Be sure that prevents it may cause eye damage. 1. stack-unit - Enter the port number of supported optics, refer to the S5000 data sheet: http://www.dell.com/us/ enterprise/p/force10-s-series/pd. • Configure the system to 11. The range is in the running configuration. When you split the port...you must be sure not to interfere with the airflow from other L2/L3 feature configurations. • For the split-port change to stack an S5000 unit. • The quad port must reload the system after issuing the CLI change . NOTE: When you cable the ports, be in ...
Dell Networking Installation Guide
Page 37
... shipping box. 2. The optic has a key that prevents it is in the correct position. Use the grab handle on the replacement module to the S5000 data sheet: http://www.dell.com/us/enterprise/p/force10-s-series/pd. Use the grab handle to slide the fan module into the end of the switch fan slot. 2. Installing... optical fibres, follow all the warning labels and always wear eye protection. Always wear an ESD-preventive wrist or heel ground strap when handling the S5000 and its components.
... shipping box. 2. The optic has a key that prevents it is in the correct position. Use the grab handle on the replacement module to the S5000 data sheet: http://www.dell.com/us/enterprise/p/force10-s-series/pd. Use the grab handle to slide the fan module into the end of the switch fan slot. 2. Installing... optical fibres, follow all the warning labels and always wear eye protection. Always wear an ESD-preventive wrist or heel ground strap when handling the S5000 and its components.
Dell Networking Installation Guide
Page 38
... two 40GbE ports in a single stack. Enter the stack member unit identifier of supported optics, refer to the S5000 data sheet: http://www.dell.com/us/enterprise/p/force10-s-series/pd. • Configure the system to stack an S5000 unit. • The quad port must reload the system after issuing the CLI change . The QSFP+ ports...
... two 40GbE ports in a single stack. Enter the stack member unit identifier of supported optics, refer to the S5000 data sheet: http://www.dell.com/us/enterprise/p/force10-s-series/pd. • Configure the system to stack an S5000 unit. • The quad port must reload the system after issuing the CLI change . The QSFP+ ports...
FTOS 9.0(1.3) Configuration Guide for the Switch
Page 941
... FTOS upgrade procedures, contact the Dell Networking Technical Support Center: • On the Web: http://support.dell.com/ • By email: Dell-Force10_Technical_Support@Dell.com • By phone: 1-866-965-5800 (USA); 408-965-5800 (international) Getting Help with Switch Information For information on switch operation, you can view data sheets and switch specifications at http...
... FTOS upgrade procedures, contact the Dell Networking Technical Support Center: • On the Web: http://support.dell.com/ • By email: Dell-Force10_Technical_Support@Dell.com • By phone: 1-866-965-5800 (USA); 408-965-5800 (international) Getting Help with Switch Information For information on switch operation, you can view data sheets and switch specifications at http...