Dell PowerSwitch S5000 Research

FTOS 9.0(1.3) Configuration Guide for the Switch

Page 43
... the USB-B Console Port • Booting Process • Entering the Initial Configuration Information • Configuring the Enable Password • Configuring a Host Name • Navigating CLI Modes • Default Configuration • Configuring Layer 2 (Data Link) Mode • Accessing the System Remotely • Configuring the Management Port IP Address • Configuring a Management Route • Configuring a Username and Password • Creating a Port-based VLAN • Assigning Interfaces to a VLAN • Assigning an IP Address to a VLAN • Connecting the S5000 to...

FTOS 9.0(1.3) Configuration Guide for the Switch

Page 672
... create an equal number of Layer 3 enabled interfaces and OSPF Process IDs. Format: A.B.C.D/M If using a Loopback interface, refer to an interface. CONFIG-INTERFACE Enable the interface. 672 | Open Shortest Path First (OSPFv2) Enabling OSPFv2 Assign an IP address to an interface (physical or Loopback) to enable OSPFv2 routing. By default OSPF, like all commands related to OSPFv2, refer to the OSPF section in the FTOS Command Line Interface document. You must have 4 interfaces with Layer 3 enabled. www.dell.com | support.dell.com • Enabling...

FTOS 9.0(1.3) Configuration Guide for the Switch

Page 793
...range: 0 to terminal lines To enable RADIUS AAA login authentication for RADIUS authentication and authorization, enter the following command in the CONFIGURATION mode: Command Syntax radius-server host {hostname | ip-address} [auth-port port-number] [retransmit retries] [timeout seconds] [key [encryption-type] key] Command Mode Purpose CONFIGURATION Enter the host name or IP address of methods: RADIUS, TACACS+, Local, None. Command Syntax aaa authorization exec {method-list-name | default} radius tacacs+ Command Mode Purpose CONFIGURATION Create methodlist with RADIUS and TACACS...

FTOS 9.0(1.3) Configuration Guide for the Switch

Page 966
... Link Trunking (VLT) VLT automatically selects a system MAC address. 3. Note: If a third-party ToR unit is never blocked. An access device never detects the change . To configure virtual link trunking and create a VLT domain in which two S5000 switches are physically connected and treated as described in VLT and VRRP interoperability:. Configuring RSTP on VLT Peers to an access device (switch or server) with the primary switch. Enable VLT...

9.13.0.0 Command Line Reference Guide for the S5000 Switch

Page 823
... 1000 Mbit, Mode full duplex ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:06:14 Queueing strategy: fifo Input 791 packets, 62913 bytes, 775 multicast Received 0 errors, 0 discarded Output 21 packets, 3300 bytes, 20 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:06:03 Example (OpenFlow DellEMC# show interfaces vlan 6 instance) Vlan 6 is down, line protocol is down Address is 00:01...

9.13.0.0 Command Line Reference Guide for the S5000 Switch

Page 1664
... the S6000-ON. Introduced on the S3048-ON. Defaults Command Modes Command History None. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. 1664 Quality of Service (QoS) Introduced on the S-Series and Z-Series. match ip vrf Uses a VRF as the match criterion, use the no match ip vrf vrf-id command. Defaults Command Modes Command History none CONF-CLASS-MAP This guide is platform-specific.

9.13.0.0 Command Line Reference Guide for the S5000 Switch

Page 1692
... View the WRED profile details. NOTE: When you can use this field. • Matched Bytes - Queue Number. • Queued Bytes - The total of the number of packets dropped for green, yellow and out-of Service (QoS) Defaults Command Modes none • EXEC • EXEC Privilege Command History This guide is platform-specific. The following list describes output of Profile 0 Usage Information In a dual homing setup, you configure...

9.13.0.0 Configuration Guide for the S5000 Switch

Page 80
...example for TeraScale and ExaScale. • For a 10-Gigabit Ethernet interface, enter the TenGigabitEthernet keyword then the slot/port information. • For a VLAN interface, enter the vlan keyword then a number from 1 to a VTY line. Configure the following command. 80 Switch Management CONFIGURATION mode ip ftp source-interface interface • Configure a password. CONFIGURATION mode ip ftp password password • Enter a username to the system by creating user profiles. The console line (console) connects you through a remote session to display the contents of an ACL...

9.13.0.0 Configuration Guide for the S5000 Switch

Page 1001
..., refer to VLT and IGMP Snooping. • All system management protocols are supported on VLT ports, including SNMP, RMON, AAA, ACL, DNS, FTP, SSH, Syslog, NTP, RADIUS, SCP, TACACS+, Telnet, and LLDP. • Enable Layer 3 VLAN connectivity VLT peers by configuring a VLAN network interface for the same VLAN on both switches. • Software features supported on VLT port-channels: • In a VLT domain, the following software features are supported on VLT physical ports: 802.1p, LLDP, flow control, port monitoring, and jumbo frames. • Software features supported...

9.112.1P1 Configuration Guide for the S5000 Switch

Page 79
... view the FTP configuration, use the show running-config ftp command in the route processor modules (RPMs). CONFIGURATION mode ip ftp password password • Enter a username to the system. The virtual terminal lines (VTYs) connect you through the console port in EXEC privilege mode, as modems. Denying and Permitting Access to a Terminal Line Dell Networking recommends applying only standard access control lists (ACLs) to deny and permit access to VTY lines. • Layer 3 ACLs deny all traffic that is applied only to a line, use...

9.112.1P1 Configuration Guide for the S5000 Switch

Page 986
... VLT interconnect fails, the VLT software on its VLT port channels. To ensure VRRP operation in a VLT domain, refer to VLT and IGMP Snooping. • All system management protocols are supported on VLT ports, including SNMP, RMON, AAA, ACL, DNS, FTP, SSH, Syslog, NTP, RADIUS, SCP, TACACS+, Telnet, and LLDP. • Enable Layer 3 VLAN connectivity VLT peers by configuring a VLAN network interface for the same VLAN on both VLT peers. If the remote peer is part of...

9.112.1P1 Command Line Reference Guide for the S5000 Switch

Page 192
...Clear the primary, secondary, or default boot parameters in the operating system. S5000 Syntax Command Modes Command History default gateway ip-address BOOT USER Version 9.0(1.3) Introduced on the S5000. enable Set the access privilege level. default gateway Set the IP address of the default gateway. S5000 Syntax Command Modes Command History boot zero {primary | secondary | default} BOOT USER Version 9.0(1.3) Introduced on the S5000. S5000 Syntax Command Modes Command History enable {user | admin} BOOT USER Version 9.0(1.3) Introduced on the S5000. 192 Boot User...

9.112.1P1 Command Line Reference Guide for the S5000 Switch

Page 766
... interfaces configured using the interface range command. display any interface with a non-default configuration. • show interfaces configured • EXEC • EXEC Privilege Command History This guide is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:05:12 Queueing strategy: fifo Time since last interface status change: 00:06:03 Example (OpenFlow Dell# show interfaces vlan 6 instance) Vlan 6 is down, line...

9.112.0P1 Command Line Reference Guide for the S5000 Switch

Page 192
default gateway Set the IP address of the default gateway. S5000 Syntax Command Modes Command History default gateway ip-address BOOT USER Version 9.0(1.3) Introduced on the S5000. 192 Boot User Mode enable Set the access privilege level. S5000 Syntax Command Modes Command History enable {user | admin} BOOT USER Version 9.0(1.3) Introduced on the S5000. S5000 Syntax Command Modes Command History boot zero {primary | secondary | default} BOOT USER Version 9.0(1.3) Introduced on the S5000. boot zero Clear the primary, secondary, or default boot parameters in the ...

9.112.0P1 Command Line Reference Guide for the S5000 Switch

Page 1562
... C-Series, E-Series, and S-Series. Traffic is considered to be green-colored up to the point at an average rate that is less than or equal to the committed rate, it is much less than the value configured.You must configure the committed rate and committed burst size with the same measurement. Defaults Command Modes Command History Layer 3 INTERFACE This guide is aggregated. Usage Information Related Commands On 40-port 10G stack-unit...

9.100.1 Command Line Reference Guide for the S5000 Switch

Page 243
S5000 Syntax enable {user | admin} Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000. default gateway Set the IP address of the default gateway. enable Set the access privilege level. S5000 Syntax help Display the Help menu. help Command Modes BOOT USER Boot User Mode 243 S5000 Syntax default gateway ip-address Command Modes BOOT USER Command History Version 9.0(1.3) Introduced on the S5000.

9.100.1 Command Line Reference Guide for the S5000 Switch

Page 1857
... number port-set number | all} [wred-profile name | multicastbandwidth percentage] command. Syntax queue egress multicast linecard {slot number port-set number | all eight egress Multicast queues or designate the percentage for the Multicast bandwidth queue. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Introduced on the C-Series and S-Series. Introduced on the S3048-ON. assigns percentage of the output QoS policy. assigns yellow or green...

9.100.0 Command Line Reference Guide for the S5000 Switch

Page 187
...S5000 Syntax Command Modes Command History default gateway ip-address BOOT USER Version 9.0(1.3) Introduced on the S5000. Available command list (30 commands total): boot change [primary|secondary|default] change operating system boot parameters boot messages disable Boot User Mode 187 enable Set the access privilege level. Example BOOT_USER # help ***** Dell Force10 Boot Interface Help Information ***** Current access level: USER LEVEL Use "syntax help BOOT USER Version 9.0(1.3) Introduced on the S5000. S5000 Syntax Command Modes Command History enable {user | admin} BOOT USER...

9.60.0 Command Line Reference Guide for the S5000 Switch

Page 2004
... relevant Dell Networking OS Command Line Reference Guide. Version 9.5(0.0) Version 9.2(0.2) Version 9.0.2.0 Version 9.0.0.0 Version 8.3.19.0 Version 8.3.12.0 Version 8.3.8.0 Introduced on the S6000. clear vlt statistics - EXEC Display the VLT statistics for NDP. Introduced on the S4820T. Introduced on the Z9000. Default Command Modes Command History Related Commands Example 2004 igmp-snoop ndp Not configured. Display the VLT statistics for IGMP snooping. Added support in the output for that VLT parameter displays. If you enter a specific keyword, such as mac...

FTOS 9.11.0 Configuration Guide for the S5000 Switch

Page 962
... two S5000 switches are physically connected and treated as MAC address and VLT primary/ secondary roles. 962 | Virtual Link Trunking (VLT) To configure virtual link trunking and create a VLT domain in VLT and VRRP interoperability:. Configure the VLT interconnect for the VLT domain. 4. (Optional) Manually reconfigure default VLT settings, such as a single port channel by the primary VLT switch. In case of a primary VLT switch failure, the secondary switch starts...

Dell PowerSwitch S5000 Research

Related Manual Pages

FTOS 9.0(1.3) Configuration Guide for the Switch

FTOS 9.0(1.3) Configuration Guide for the Switch

FTOS 9.0(1.3) Configuration Guide for the Switch

FTOS 9.0(1.3) Configuration Guide for the Switch

9.13.0.0 Command Line Reference Guide for the S5000 Switch

9.13.0.0 Command Line Reference Guide for the S5000 Switch

9.13.0.0 Command Line Reference Guide for the S5000 Switch

9.13.0.0 Configuration Guide for the S5000 Switch

9.13.0.0 Configuration Guide for the S5000 Switch

9.112.1P1 Configuration Guide for the S5000 Switch

9.112.1P1 Configuration Guide for the S5000 Switch

9.112.1P1 Command Line Reference Guide for the S5000 Switch

9.112.1P1 Command Line Reference Guide for the S5000 Switch

9.112.0P1 Command Line Reference Guide for the S5000 Switch

9.112.0P1 Command Line Reference Guide for the S5000 Switch

9.100.1 Command Line Reference Guide for the S5000 Switch

9.100.1 Command Line Reference Guide for the S5000 Switch

9.100.0 Command Line Reference Guide for the S5000 Switch

9.60.0 Command Line Reference Guide for the S5000 Switch

FTOS 9.11.0 Configuration Guide for the S5000 Switch

Similar Questions

Ask a New Question

Manuals / Documents

Related Items

Points & Prizes

Dell Manuals

Dell Reviews

Contact Information

Scoreboard Ratings

Dell Recalls