DWL-3600AP Datasheet
Page 3
DWL-3600AP Unified N Access Point Technical Specifications System Wi-Fi Interface LAN Interface Antenna Antenna Gain Power Method Wireless Frequency Data Transfer Rate Operation Channel (2.4 GHz) System Management Security SSID Wireless Security Detection & Prevention Authentication Physical & Environmental Power Adapter Power over Ethernet Stand-Alone Mode Managed Mode (Managed by D-Link... Address Filtering • AP Load Balancing Setup • Centralized Management • Centralized Firmware Dispatch • Visualized AP Management Tool • Auto-Power Adjustment • Dynamic ...
DWL-3600AP Unified N Access Point Technical Specifications System Wi-Fi Interface LAN Interface Antenna Antenna Gain Power Method Wireless Frequency Data Transfer Rate Operation Channel (2.4 GHz) System Management Security SSID Wireless Security Detection & Prevention Authentication Physical & Environmental Power Adapter Power over Ethernet Stand-Alone Mode Managed Mode (Managed by D-Link... Address Filtering • AP Load Balancing Setup • Centralized Management • Centralized Firmware Dispatch • Visualized AP Management Tool • Auto-Power Adjustment • Dynamic ...
Users Manual
Page 5
... Restoring the Configuration from a Previously Saved File 118 Performing AP Maintenance...120 Resetting the Factory Default Configuration 120 Rebooting the Access Point ...120 Upgrading the Firmware ...120 Packet Capture Configuration and Settings 122 Packet Capture Status...124 Packet Capture Parameter Configuration 124 Packet File Capture ...125 Remote Packet Capture ...125 Packet...
... Restoring the Configuration from a Previously Saved File 118 Performing AP Maintenance...120 Resetting the Factory Default Configuration 120 Rebooting the Access Point ...120 Upgrading the Firmware ...120 Packet Capture Configuration and Settings 122 Packet Capture Status...124 Packet Capture Parameter Configuration 124 Packet File Capture ...125 Remote Packet Capture ...125 Packet...
Users Manual
Page 23
...for the AP. Enter the name, e‐mail address, or phone number of the WLAN AP firmware become available, you change it as bullet characters to the AP. D-Link November 2011 Unified Access Point Administrator's Guide Page 23 As new versions of the person to contact...must match the baud rate on the AP. Unified Access Point Administrator's Guide Basic Settings Table 4: Basic Settings Page (Cont.) Field Description Firmware Version Shows version information about the product hardware. Device Name Generic name to 8 characters. Enter a new administrator password. Use up to ...
...for the AP. Enter the name, e‐mail address, or phone number of the WLAN AP firmware become available, you change it as bullet characters to the AP. D-Link November 2011 Unified Access Point Administrator's Guide Page 23 As new versions of the person to contact...must match the baud rate on the AP. Unified Access Point Administrator's Guide Basic Settings Table 4: Basic Settings Page (Cont.) Field Description Firmware Version Shows version information about the product hardware. Device Name Generic name to 8 characters. Enter a new administrator password. Use up to ...
Users Manual
Page 117
... (1 to 63 characters) for Download Method. 2. Enter the IP address of the information about the AP settings. D-Link November 2011 Unified Access Point Administrator's Guide Page 117 "Rebooting the Access Point" • "Upgrading the Firmware" • "Packet Capture Configuration and Settings" Saving the Current Configuration to save as a back‐up copy...
... (1 to 63 characters) for Download Method. 2. Enter the IP address of the information about the AP settings. D-Link November 2011 Unified Access Point Administrator's Guide Page 117 "Rebooting the Access Point" • "Upgrading the Firmware" • "Packet Capture Configuration and Settings" Saving the Current Configuration to save as a back‐up copy...
Users Manual
Page 120
...information. If the upgrade fails, the original firmware remains as a troubleshooting measure, you can reboot the UAP. Note: When you upload new firmware and the system reboots, the newly added firmware becomes the primary image. D-Link November 2011 Unified Access Point Administrator's Guide ...Page 120 Use the following steps to upgrade the firmware on the Configuration page. This restores factory...
...information. If the upgrade fails, the original firmware remains as a troubleshooting measure, you can reboot the UAP. Note: When you upload new firmware and the system reboots, the newly added firmware becomes the primary image. D-Link November 2011 Unified Access Point Administrator's Guide ...Page 120 Use the following steps to upgrade the firmware on the Configuration page. This restores factory...
Users Manual
Page 121
...Upgrade page (or the Basic Settings page). The firmware upgrade file supplied must be a tar file. The firmware upgrade file supplied must be a tar file. Click Upgrade to confirm the upgrade and start the process. D-Link November 2011 Unified Access Point Administrator's Guide Page ...121 Unified Access Point Administrator's Guide Upgrading the Firmware For example, to upload the ap_upgrade.tar image located in the /share/builds/ap...
...Upgrade page (or the Basic Settings page). The firmware upgrade file supplied must be a tar file. The firmware upgrade file supplied must be a tar file. Click Upgrade to confirm the upgrade and start the process. D-Link November 2011 Unified Access Point Administrator's Guide Page ...121 Unified Access Point Administrator's Guide Upgrading the Firmware For example, to upload the ap_upgrade.tar image located in the /share/builds/ap...
Users Manual
Page 122
...before the upgrade. 5. When the upgrade is indicated. Do not power down the access point while the upgrade is formatted in process. D-Link November 2011 Unified Access Point Administrator's Guide Page 122 The file is in pcap format and can capture the following types of packets: ... begins once you can transfer the file to an external PC running the Wireshark® tool. To verify that the firmware upgrade completed successfully, check the firmware version shown on the internal logical interfaces such as Wireshark and OmniPeek. If the upgrade was successful, the updated version...
...before the upgrade. 5. When the upgrade is indicated. Do not power down the access point while the upgrade is formatted in process. D-Link November 2011 Unified Access Point Administrator's Guide Page 122 The file is in pcap format and can capture the following types of packets: ... begins once you can transfer the file to an external PC running the Wireshark® tool. To verify that the firmware upgrade completed successfully, check the firmware version shown on the internal logical interfaces such as Wireshark and OmniPeek. If the upgrade was successful, the updated version...