Cub Cadet 3X 28 inch INTELLIPOWER Support and Manuals
Get Help and Manuals for this Cub Cadet item
View All Support Options Below
Free Cub Cadet 3X 28 inch INTELLIPOWER manuals!
Problems with Cub Cadet 3X 28 inch INTELLIPOWER?
Ask a Question
Free Cub Cadet 3X 28 inch INTELLIPOWER manuals!
Problems with Cub Cadet 3X 28 inch INTELLIPOWER?
Ask a Question
Popular Cub Cadet 3X 28 inch INTELLIPOWER Manual Pages
Operation Manual - Page 1
... site, Customer Support Department, or with these instructions may result in personal injury -
SAVE THESE INSTRUCTIONS. Model Number Serial Number
WARNING
Read and follow all models and the model depicted may vary by standing at the operator's position and looking at the rear, right side of California to the right. Failure to operate this manual before attempting...
Operation Manual - Page 4
...replace with California and federal EPA emission regulations for any adjustments, or inspections.
18. "Use of your hand in this manual.
2. Check fuel line, tank, cap, and fittings frequently for assistance and the name of parts which do not meet the original equipment specifications...authorized service dealer to improper performance and compromise safety!"
6. Contact Customer Support ...
Operation Manual - Page 6
... Manual ...guides. Refer to Figure 7 to Handle Assembly.
• Install the chute.
Figure 3
4. Ensuring any cables, and wiring harness are clear of equipment to the lower handle (if applicable), set aside as shown in roller guides (Figure 3). Refer to model...Set-up.
• If necessary make adjustments to lower handle.
NOTE: On models with Overhead Chute Control (with side supports...
Operation Manual - Page 7
...Chute Control
Style" and continue to the "Assembly" instructions for models with a
metal chute assembly. SET-UP
5. See Figure 5 or Figure 6 for
your specific style on pages13 - 18.
*Chute
Assembly
Chute ... Control (Flex Shaft)
*Chute
Assembly
Electric Chute Control
*NOTE: This model may
be equipped with
b
side supports. Attach the two carriage bolts (b) and nuts (a) removed in Step ...
Operation Manual - Page 12
... install the same as the standard chute shown in fastest forward speed.
2. A Non-Hydro Models B Hydro Models
...Figure 33 4. Insert ferrule into top hole of flex shaft into chute control rod coupling under handle panel. Make sure the shift lever on shift rod (d) and pull it out from shift lever (e) (Figure 32 inset). SET-UP
6. e
c
a
Chute Control Rod
or
Manual...
Operation Manual - Page 13
...to achieve further engagement of coupler. Finish securing chute control head by installing hex screw (c)
and wing nut (b) removed in Step 1 (...Support Bracket
dac
121
e
Chute
Chute Base
b
Figure 35
NOTE: For smoothest operation, cables should all be to Operation, Manual Chute Rotation Control & Electric Chute Control on page 16. SET-UP
1. c
b
Figure 38 5.
NOTE: For models...
Operation Manual - Page 16
... from hole closest to desired height. 3. SET-UP
Adjustable Drift Cutters (If Equipped) The drift cutters are mounted inverted at bottom of chute assembly. The chute control rod (b) will need to the sides of auger housing. Manual Chute pitch Adjustment (If Equipped) NOTE: For models without manual chute pitch, see Operation on left side...
Operation Manual - Page 17
...bracket downward to operating, carefully read and follow all instructions below. a
b
Figure 55 Shift Rod (If ...Repeat the steps 1 - 6 to remain engaged for ALL moving parts to one of speeds (forward and reverse) cannot be achieved,... Operator's Manual.
3. Place shift lever in the shift cable index bracket. SET-UP
a
a
b
b
b
b
b a
d
c
c
c
c
Figure 53
NOTE: 3-Stage model shown.
...
Operation Manual - Page 18
... drive cable bracket upward to provide more slack (or downward
to the Engine Operator's Manual. Refer to re-adjust the drive control.
18
NOTE: If excessive slack is present...If any of drive control lever as follows:
1. Drive Control (Hydro Models) (If Equipped) When drive control lever is in drive control cable. SET-UP
e
5. Re-tighten the hex screws. 8. If necessary
repeat Steps...
Operation Manual - Page 19
...instructional manual supplied with battery charger for information on the battery box floor. Insert the battery pack (e) into the battery box so that the battery gauge button and battery gauge (f) are facing the front of your nearest servicing dealer. Close the battery box cover.
Installing...EQUIPPED)
IMPORTANT: Fully charge the battery. SET-UP
Snowblower Equipped with care and keep...
Operation Manual - Page 21
... & Set-Up section prior to the reverse direction will result in reverse. H. Moving past the detent position to operating your Engine Operator's Manual for... are two reverse (R) speeds. Read and follow all instructions carefully and perform all adjustments to all features in Figure... cleared. Not all snow blower models and the snow blower depicted may vary by model.
E. G. Figure 63
NOTE:...
Operation Manual - Page 27
... plug wire. Tire Pressure Refer to Auger Control on page 25.
2. a
• Refer to Tire Pressure on page 26. TROUBLESHOOTING
Chute fails to Engine Operator's Manual. Refer to Auger Belt Replacement on page 26. Repair as directed in need of Blowing 1.
Remove four carriage bolts (a) and hex flange nuts (b) and
flat washers (c) which secure...
Operation Manual - Page 28
...Manual for 5 - 10 minutes to drain fuel from underside by removing selftapping screws (Figure 82).
5. Lubricate machine as instructed... and forward so that it is not being serviced, it rests on aluminum drive plate or rubber...3-in a clean, dry area.
6. See Installing/Removing The Battery Pack on page 28.
5.
... coat the snow blower.
7. Non-Hydro Models (If Equipped)
a b
Figure 81
The...
Operation Manual - Page 30
...authorized service dealer to axle. Follow the instructions below. Remove frame cover from around auger pulley, and slip it to have friction wheel rubber replaced or contact Customer Support. ... problem, the friction wheel may need to frame after installing a replacement auger belt (Figure 88). 9. Ball Bearing
a
Figure 91 NOTE: Be careful not to be replaced.
After replacing ...
Operation Manual - Page 31
...your nearest servicing dealer. bb
bb
Figure 93 10. Apply a light coating of your authorized service dealer to have the Hydro Transmission serviced or contact Customer Support for disposal instructions. Slide ...NOTE: If you 're disassembling friction wheel and replacing only rubber ring, proceed as a whole, discard the worn part and slide new part onto hex shaft. 7. Follow previous steps in...
Cub Cadet 3X 28 inch INTELLIPOWER Reviews
We have not received any reviews for Cub Cadet yet.