Cub Cadet 3X 26 inch TRAC Support and Manuals
Get Help and Manuals for this Cub Cadet item
View All Support Options Below
Free Cub Cadet 3X 26 inch TRAC manuals!
Problems with Cub Cadet 3X 26 inch TRAC?
Ask a Question
Free Cub Cadet 3X 26 inch TRAC manuals!
Problems with Cub Cadet 3X 26 inch TRAC?
Ask a Question
Popular Cub Cadet 3X 26 inch TRAC Manual Pages
Operation Manual - Page 1
... necessary, should you seek technical support via our web site, Customer Support Department, or with these instructions may vary by standing at the operator's position and looking down at the rear of California to the right. Safe Operation Practices • Assembly • Adjustments • Operation • Service And Maintenance
Operator's Manual
Snow Blower
2-Stage and...
Operation Manual - Page 4
... the machine in accidents, injuries or death. Refer to unclog the discharge opening. Replace if necessary.
13. Never tamper with original equipment manufacturer's (OEM) parts only. Never put your safety protection, frequently check all components and replace with factory setting of starter cord (kickback) will pull hand and arm toward engine faster than you...
Operation Manual - Page 6
... roller guides (Figure 2). Refer to the Engine Operator's Manual shipped with steel rod speed selectors, you may need to lower shift rod to the side slightly to the engine, if equipped. Observe lower rear area of equipment to lower handle.
Refer to Set-Up.
• If necessary make adjustments to Handle Assembly.
• Install...
Operation Manual - Page 10
...
10 Refer to ensure rod is inserted all the way into pinion gear. Make sure to Set-Up (page 13).
STOP
Continue to line up with hole in chute control input collar closest to chute support bracket with arrow on pinion gear, and will be visible after rod has been fully inserted...
Operation Manual - Page 11
...shift rod (Figure 26 inset).
11
Figure 28 Ferrule may need to be to Set-Up (page 13).
Insert flex shaft (b) into chute control rod coupling under handle...of coupler. Insert hex end of chute control head (Figure 23). Figure 24 • Models with
hairpin clip (c) and washer (d) removed in fastest forward speed. 8. Ferrule
a
4.
...
Manual Chute Control Rod
Figure 25 7.
Operation Manual - Page 12
...manual...models equipped with manual chute control rods, the hole closest to Operation, Manual... Chute Rotation Control & Electric Chute Control on page 15. Refer to chute control head is a reference hole provided at rear end of control rod to the left of chute control rod into chute control head.
Insert round end of coupler.
d
e
Figure 31 4. Refer to Set... support ...support bracket with...
Operation Manual - Page 13
... EQUIPPED) The drift cutters are routed through a single wire guide (a) on top of the engine and/or through the wire guides will vary depending on the front and left of the chute control rod (c). ASSEMBLY
Set-Up
CHUTE CONTROL CABLE ROUTING (IF EQUIPPED) For models equipped with 2-way or 4-way chute controls, electric chute...
Operation Manual - Page 14
SKID SHOES (IF APPLICABLE) Select models require the installation to carriage bolts (b).
WARNING
Use extreme caution when ... be cleared is against ground to provide a minimum of 1/8th inch clearance between ground and shave plate.
1. Adjustments
SKID SHOES Snow blower skid shoes are mounted inverted at a factory setting roughly 1/8" below the shave plate.
b
b
a
Figure 41
...
Operation Manual - Page 15
... thrown can be held stationary when tightening the nut (Figure 44).
MANUAL CHUTE PITCH ADJUSTMENT NOTE: For models without manual chute pitch, see Controls and Operation on page 15.
b
a
Figure...Reinstall and securely tighten all instructions below. Readjust the skid shoes. Securely tighten the two carriage bolts and wing knob that it lines up with manual chute pitch, the distance...
Operation Manual - Page 19
.... CAUTION
Operate the snow blower in this manual are applicable to all snow blower models and the snow blower depicted may differ from...described below and may be illustrated in the Assembly & Set-Up section prior to operating your snow blower.
SKID SHOES...is operating safely and properly. Read and follow all instructions carefully and perform all features in open areas until you...
Operation Manual - Page 20
...the upper chute, which will change the chute direction on models equipped with the third hole in chute control head (Figure ...8226; To change the direction in it lines up to the desired setting (a) (Figure 57). • To Increase the Distance Snow is ... the left side of the snow blower under the handle panel. MANUAL CHUTE ROTATION CONTROL & ELECTRIC CHUTE
CONTROL (JOYSTICK) (IF EQUIPPED)...
Operation Manual - Page 23
... control cable in the Assembly & Set-up section. Repair as directed in need of the snow blower are subject to Auger Belt Replacement on page 22.
3.
Foreign object...for engine-related troubleshooting and service. See Engine Operator's Manual. Engine fails to Replacing Shear Pins on select models) have two wear edges. Drive belt loose or damaged.
• Replace drive belt....
Operation Manual - Page 24
...hex shaft should be used until it to Engine Operator's Manual for information on the ground. If adjusting the shave ...
Allow engine to run until next season, follow the storage instructions below.
1.
Lubrication
CHUTE ROTATION CONTROL (IF EQUIPPED) Once a... (25) hours of the engine and the snow blower.
6. SERVICE AND MAINTENANCE
To remove shave plate: 1. If storing in the ...
Operation Manual - Page 25
...
Figure 74 3.
See an authorized Service Dealer to run until it is equipped with the LED light bar on front of fuel. SERVICE AND MAINTENANCE
AUGER SHAFT At least ...BELT REPLACEMENT To remove and replace auger belt, proceed as follows:
1.
Remove safety key or disconnect spark plug wire.
2. a a
b
b
NOTE: Three Stage
b
Augers Shown
Figure 71
IMPORTANT: On 3-stage models,...
Operation Manual - Page 26
... frame cover from underside by following instructions in Assembly & Set-Up section (page 15).
26 FRICTION WHEEL INSPECTION If snow blower fails to drive with drive control lever engaged, and performing drive control cable adjustment fails to correct problem, the friction wheel may need to frame after installing a replacement auger belt (Figure 76).
9. Allow engine...
Cub Cadet 3X 26 inch TRAC Reviews
We have not received any reviews for Cub Cadet yet.