Installation Guide
Page 2
... Ethernet interfaces. To ensure a smooth upgrade, perform the following procedure only if you are upgrading to an NPE-G1 or NPE-G2 from an NPE-G1, you do not need to perform the following considerations: • The NPE-G1 and NPE-G2 contain an I /O controller. You therefore must... Cisco IOS software image and configuration files available to the NPE-G1 or NPE-G2 is a different procedure than previous processor upgrades because of the Type 2 Flash Disk memory used in a chassis, you are upgrading to an NPE-G2 from an NPE-400 or earlier network processing engine. Note The NPE-G2 ...
... Ethernet interfaces. To ensure a smooth upgrade, perform the following procedure only if you are upgrading to an NPE-G1 or NPE-G2 from an NPE-G1, you do not need to perform the following considerations: • The NPE-G1 and NPE-G2 contain an I /O controller. You therefore must... Cisco IOS software image and configuration files available to the NPE-G1 or NPE-G2 is a different procedure than previous processor upgrades because of the Type 2 Flash Disk memory used in a chassis, you are upgrading to an NPE-G2 from an NPE-400 or earlier network processing engine. Note The NPE-G2 ...
Installation Guide
Page 3
... Disk shipped with the NPE-G1 or NPE-G2 is properly formatted, however, you can write to it to a CompactFlash Disk on page 7-4. You do not need to perform this by other computers. OL-4448-12 Network Processing Engine and Network Services Engine Installation and Configuration 7-3 If...controller, as described in Step 3. Step 4 (Optional) Copy the proper Cisco IOS software image (see Table 8-4 on the NPE-G1 or NPE-G2. See the "Copying the Configuration File" section on the NPE-G1 or NPE-G2. Then insert the CompactFlash Disk and adapter into the existing I /O controller...
... Disk shipped with the NPE-G1 or NPE-G2 is properly formatted, however, you can write to it to a CompactFlash Disk on page 7-4. You do not need to perform this by other computers. OL-4448-12 Network Processing Engine and Network Services Engine Installation and Configuration 7-3 If...controller, as described in Step 3. Step 4 (Optional) Copy the proper Cisco IOS software image (see Table 8-4 on the NPE-G1 or NPE-G2. See the "Copying the Configuration File" section on the NPE-G1 or NPE-G2. Then insert the CompactFlash Disk and adapter into the existing I /O controller...
Installation Guide
Page 63
... to point to boot. The router reverts to boot ROMmon before doing any other network processor engine for upgrading your system) that is performing an initial bootup. biff Source filename []? c7200-boot-mz.120-5.S Destination filename [...NPE-G2, but cannot be upgraded on the NPE-G1 or NPE-G2 Step 3 Copy the boot helper image from 192.168.254.254 (via Ethernet4/0 [OK - 3132516/6264832 bytes] 3132516 bytes copied in 28.488 secs (111875 bytes/sec) This completes the procedure for the Cisco 7200 series routers. OL-4448-12 Network Processing Engine and Network Services Engine...
... to point to boot. The router reverts to boot ROMmon before doing any other network processor engine for upgrading your system) that is performing an initial bootup. biff Source filename []? c7200-boot-mz.120-5.S Destination filename [...NPE-G2, but cannot be upgraded on the NPE-G1 or NPE-G2 Step 3 Copy the boot helper image from 192.168.254.254 (via Ethernet4/0 [OK - 3132516/6264832 bytes] 3132516 bytes copied in 28.488 secs (111875 bytes/sec) This completes the procedure for the Cisco 7200 series routers. OL-4448-12 Network Processing Engine and Network Services Engine...