Cisco NM-4B-S/T= - Interface Module ISDN-BRI Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco NM-4B-S/T= manuals!
Problems with Cisco NM-4B-S/T=?
Ask a Question
Free Cisco NM-4B-S/T= manuals!
Problems with Cisco NM-4B-S/T=?
Ask a Question
Popular Cisco NM-4B-S/T= Manual Pages
User Guide - Page 2
... 25 • Quality of Service, page 29 • Maximum Number of the packet. or 36-port Ethernet switch network modules in Cisco AVVID Architecture, page 40 • Stacking, page 41 • Flow Control, page 41 • Fallback Bridging, page 42
Layer 2 Ethernet Interfaces
Layer 2 Ethernet Switching Ethernet switch network modules support simultaneous, parallel connections between different...
User Guide - Page 5
...renaming of problems, such ... Module ...Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
5
SVIs support routing protocol and bridging configurations. The VLAN corresponds to use... network....specifications, and security violations.
A routed port is not supported). 16- VTP minimizes misconfigurations and configuration inconsistencies that maintains VLAN configuration consistency by using...
User Guide - Page 7
...Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
VTP Version 2 If you use VTP in your network... reducing part of ...network module and another switch or host. 16-
Consistency checks are version 2-capable. If the digest on each EtherChannel must configure a password on a received VTP message is correct, its other trunks, even for TLVs it is supported in the NM...
User Guide - Page 9
... and interacting with Ethernet switch network module
• Client-the device (workstation) that requests access to the LAN and switch services and responds to the client. The switch acts as the proxy, the authentication service is reencapsulated in the Microsoft Windows XP operating system. (The client is the only supported authentication server; The workstation must...
User Guide - Page 29
... network module supports this combination, the ACL is allowed, but cannot be used for Configuring ACLs on page 28. Table 5 lists a summary of service (QoS) but you can be implemented on your Ethernet switch network module. On a given interface, only one ACL can provide preferential treatment to each packet, regardless of user-defined masks for Cisco 2600 Series, Cisco...
User Guide - Page 31
... queues, CoS values, and weights for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Note Layer 3 IPv6 packets are then serviced on the QoS features offered by the switch. 16-
For more information, see the "Classification" section on the Layer 2 switch ports.
The Ethernet switch network module can be a simple or complex...
User Guide - Page 33
... network modules.
• System-defined masks are a part of profile. System-defined masks that you can include matching the access group defined by using the...part of a deny action is matched against a specific traffic flow to take on the 16- Actions can create another that you want to classify, you can include setting a specific DSCP value in class maps with the ACL, you use...
User Guide - Page 35
...
Cisco ..., QoS uses the configurable... specific...service. The LAN switch snoops on page 96. Packets are handled according to the interface.
16- For example, the maximum number for 10 VLANs and 20 groups would be appropriate for QoS, traffic in the physical port egress queue depending on Ethernet switch network modules.
On a trunk interface configured for your network. IP Multicast Support...
User Guide - Page 36
... and are deleted. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
36 Ethernet switch network modules support a maximum of these...support both user-defined and IGMP snooping-learned settings. After it relays the IGMP queries from the multicast router, it deletes entries periodically if it removes the host port from a host, it does not receive any automatic manipulation by using...
User Guide - Page 37
... sends an IGMP join message for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Joining a Multicast... recognizes IGMP packets and forwards them to set up a multicast forwarding table entry as shown...by Host 1, the CPU uses the information to the CPU. This prevents the CPU from becoming overloaded with Ethernet switch network module
1 IGMP Report 224.1.2.3
CPU...
User Guide - Page 38
... to these queries with Ethernet switch network module
1
CPU port Multicast Forwarding
Table
88848
2
3
4
5
Host 1 Host 2 Host 3 Host 4
Table 8 Updated Multicast Forwarding Table
Destination Address 0100.5e01.0203
Type of the interfaces. Global Storm-Control
Global storm-control prevents switchports on one host in the forwarding table for the specific multicast group. If, after...
User Guide - Page 40
... that can also set the switch to block and then restore the forwarding of broadcast, unicast, or multicast packets are included: • Configuring the Ethernet Switch Network Module for Cisco AVVID/IP Telephony, page 40 • Default Switch Configuration, page 41
Configuring the Ethernet Switch Network Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Per...
User Guide - Page 81
... protocol type. Note The Ethernet switch network module does not support dynamic or reflexive access lists. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
81
Table 12 Filtering Parameter ACEs Supported by Different IP Protocols
Filtering Parameter
TCP
UDP
Layer 3 Parameters: IP ToS byte1
No
No
Differentiated Services Code Point (DSCP)
No
No
IP source...
User Guide - Page 108
... can configure the Ethernet switch network module so that the voice and data traffic coexist on the same subnet might be used exclusively for branch offices. (This is one of the simpler ways to deploy IP telephony.) When this marking changed to a Differentiated Services Code Point ([DSCP]) value of 5. (With Cisco CallManager Release 3.0(5), this is impractical...
User Guide - Page 113
... 5
Router(config-if)# end Router# show interface switchport
Purpose
Enters global configuration mode. Instructs the switch to use VLAN 0 (default native VLAN) to a Cisco 7960 IP phone.
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
113 There are carried on a Ethernet switch network module
The Ethernet switch network module can supply inline power to a Cisco 7960 IP phone...
Cisco NM-4B-S/T= Reviews
Do you have an experience with the Cisco NM-4B-S/T= that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!