Hardware Installation Guide
Page 90
... the DTE interface. The functions of service signal from the DTE interface. AL One of these alarm conditions is being transmitted to Installing Cisco Interface Cards in Cisco Access Routers. This WIC also supports 64-kbps dedicated lines. (See Figure 56.) Figure 56 WIC-1DSU-56K4 Front Panel 56- RD Data is ...is communicating with is off during normal operation. or 64-kbps port LEDs LED TD RD LP AL CD 41224 SEE MANUAL BEFORE INSTALLATION DSU 56K 56/64-kbps DSU/CSU WIC LEDs The 56/64-kbps DSU/CSU WIC LEDs, are described in Figure 56. This LED is properly grounded...
... the DTE interface. The functions of service signal from the DTE interface. AL One of these alarm conditions is being transmitted to Installing Cisco Interface Cards in Cisco Access Routers. This WIC also supports 64-kbps dedicated lines. (See Figure 56.) Figure 56 WIC-1DSU-56K4 Front Panel 56- RD Data is ...is communicating with is off during normal operation. or 64-kbps port LEDs LED TD RD LP AL CD 41224 SEE MANUAL BEFORE INSTALLATION DSU 56K 56/64-kbps DSU/CSU WIC LEDs The 56/64-kbps DSU/CSU WIC LEDs, are described in Figure 56. This LED is properly grounded...
Hardware Installation Guide
Page 91
... WIC to a 56/64-kbps Services Wall Jack Switched 56/64-kbps port (RJ-48S) SEE MANUAL BEFORE INSTALLATION DSU 56K Straight-through RJ-48S-to-RJ-48S cable (not included) to connect a 56/64-kbps DSU/CSU WIC to a ...48S-to-RJ-48S cable TD RD LP AL CD 43737 Step 4 Step 5 RJ-48S jack Turn on power to the router. Connect one end of the cable to the network and contains the following sections: • T1/FT1 DSU/CSU WICs ... in Figure 57. Check that the CD LED comes on, which indicates that the router is communicating with the DSU/CSU at the 56/64-kbps service provider's central office.
... WIC to a 56/64-kbps Services Wall Jack Switched 56/64-kbps port (RJ-48S) SEE MANUAL BEFORE INSTALLATION DSU 56K Straight-through RJ-48S-to-RJ-48S cable (not included) to connect a 56/64-kbps DSU/CSU WIC to a ...48S-to-RJ-48S cable TD RD LP AL CD 43737 Step 4 Step 5 RJ-48S jack Turn on power to the router. Connect one end of the cable to the network and contains the following sections: • T1/FT1 DSU/CSU WICs ... in Figure 57. Check that the CD LED comes on, which indicates that the router is communicating with the DSU/CSU at the 56/64-kbps service provider's central office.
Hardware Installation Guide
Page 96
...; "Configuring Serial Interfaces" chapter in the Cisco IOS Interface Configuration Guide for your Cisco IOS software release • 56K CSU Support for the Cisco Signaling Link Terminal, Cisco IOS Release 12.2(2)T feature module • Cisco Signaling Link Terminal, Cisco IOS Release 12.1(1)T feature module • ... new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html CCVP, the Cisco logo, and Welcome to the Human Network are shown for the Cisco 1700, Cisco 2600, Cisco 3600, and Cisco 3700 Series Routers, Cisco IOS Release 12.2(...
...; "Configuring Serial Interfaces" chapter in the Cisco IOS Interface Configuration Guide for your Cisco IOS software release • 56K CSU Support for the Cisco Signaling Link Terminal, Cisco IOS Release 12.2(2)T feature module • Cisco Signaling Link Terminal, Cisco IOS Release 12.1(1)T feature module • ... new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html CCVP, the Cisco logo, and Welcome to the Human Network are shown for the Cisco 1700, Cisco 2600, Cisco 3600, and Cisco 3700 Series Routers, Cisco IOS Release 12.2(...