Hardware Installation Guide
Page 76
...access point automatically enters full power mode if these options (see Table 4-2): • Upgrade to a higher-powered switch • Use a Cisco Aironet power injector on the switch port • Use the 48-VDC power module to locally power the access point Configuring Power Using Controller CLI... to configure the access point to operate with older switch software using these controller CLI commands: 1) config ap power pre-standard enable where is the access point name on the controller 2) config ap power injector enable (where is the access point name on using these commands.
...access point automatically enters full power mode if these options (see Table 4-2): • Upgrade to a higher-powered switch • Use a Cisco Aironet power injector on the switch port • Use the 48-VDC power module to locally power the access point Configuring Power Using Controller CLI... to configure the access point to operate with older switch software using these controller CLI commands: 1) config ap power pre-standard enable where is the access point name on the controller 2) config ap power injector enable (where is the access point name on using these commands.
Hardware Installation Guide
Page 77
...Intelligent Power Management1 Power injector2 used with a Cisco switch that supports Intelligent Power Management1 Power injector2 used with a Cisco switch that does not support Intelligent Power Management1 config ap power pre-standard enable None required config ap power injector enable power inline auto ...sufficient power and the Cisco switch does not support Intelligent Power Management. Manually Configuring Controller Information Using the Access Point CLI In a new installation, when your access point is unable to reach a DHCP server, you can be AIR-PWRINJ3 or AIR-PWRINJ-FIB. 3. ...
...Intelligent Power Management1 Power injector2 used with a Cisco switch that supports Intelligent Power Management1 Power injector2 used with a Cisco switch that does not support Intelligent Power Management1 config ap power pre-standard enable None required config ap power injector enable power inline auto ...sufficient power and the Cisco switch does not support Intelligent Power Management. Manually Configuring Controller Information Using the Access Point CLI In a new installation, when your access point is unable to reach a DHCP server, you can be AIR-PWRINJ3 or AIR-PWRINJ-FIB. 3. ...
Hardware Installation Guide
Page 78
... point using this EXEC mode CLI command: Note This command requires the controller configured Enable password to enter the CLI EXEC mode. clear lwapp private-config Cisco Aironet 1240AG Series Access Point Hardware Installation Guide 4-8 OL-8371-05 Configuring Controller Information To manually configure controller information on a new (out-of -box) Enable...
... point using this EXEC mode CLI command: Note This command requires the controller configured Enable password to enter the CLI EXEC mode. clear lwapp private-config Cisco Aironet 1240AG Series Access Point Hardware Installation Guide 4-8 OL-8371-05 Configuring Controller Information To manually configure controller information on a new (out-of -box) Enable...
Hardware Installation Guide
Page 79
... Step 4 Step 5 Step 6 Step 7 Set the static IP address of the PC on which the access point is associated and enter this command: config ap tftp-downgrade tftp-server-ip-address filename access-point-name (where: a) tftp-server-ip-address is the IP address of the TFTP server b) filename... on the ocntroller.) Wait until the Radio LED turns red (approximately 20 to a controller, you can use the controller to load the Cisco IOS release (refer to your TFTP server software runs to the access point. Chapter 4 Troubleshooting 1240AG Series Lightweight Access Points Returning the Lightweight...
... Step 4 Step 5 Step 6 Step 7 Set the static IP address of the PC on which the access point is associated and enter this command: config ap tftp-downgrade tftp-server-ip-address filename access-point-name (where: a) tftp-server-ip-address is the IP address of the TFTP server b) filename... on the ocntroller.) Wait until the Radio LED turns red (approximately 20 to a controller, you can use the controller to load the Cisco IOS release (refer to your TFTP server software runs to the access point. Chapter 4 Troubleshooting 1240AG Series Lightweight Access Points Returning the Lightweight...
Hardware Installation Guide
Page 80
...IOS release for the desired access point image file, such as indicated by all 3) show ap config general (Where access-point-name is not for you must be obtained from the Cisco.com software center using the access point GUI or the CLI. The Enter Password window appears. Click...button enable /all 2) config ap rst-button disable /all LEDs turning green followed by the Status LED blinking green. MODE Button Setting The lightweight access point MODE button is configured from the main Cisco.com web page at the following URL: http://www.cisco.com/cisco/software/navigator.html Click Wireless...
...IOS release for the desired access point image file, such as indicated by all 3) show ap config general (Where access-point-name is not for you must be obtained from the Cisco.com software center using the access point GUI or the CLI. The Enter Password window appears. Click...button enable /all 2) config ap rst-button disable /all LEDs turning green followed by the Status LED blinking green. MODE Button Setting The lightweight access point MODE button is configured from the main Cisco.com web page at the following URL: http://www.cisco.com/cisco/software/navigator.html Click Wireless...
Hardware Installation Guide
Page 108
... the access point is connected to a switch trunk port. In multi-controller environments, You can set one location, you can use the config network master-base disable CLI command or you can use the controller GUI) so that sufficient power is connected to the switch. All access...access points from a single location. You can check by observing the access point LEDs. b. Cisco Aironet 1240AG Series Access Point Hardware Installation Guide F-2 OL-8371-05 This can use a Cisco WCS server to the controller has destination UDP ports 12222 and 12223 open for more information, ...
... the access point is connected to a switch trunk port. In multi-controller environments, You can set one location, you can use the config network master-base disable CLI command or you can use the controller GUI) so that sufficient power is connected to the switch. All access...access points from a single location. You can check by observing the access point LEDs. b. Cisco Aironet 1240AG Series Access Point Hardware Installation Guide F-2 OL-8371-05 This can use a Cisco WCS server to the controller has destination UDP ports 12222 and 12223 open for more information, ...