Cisco WAP200 Support Question
Cisco WAP200 Support Question
Find answers below for this question about Cisco WAP200 - Small Business Wireless-G Access Point.Need a Cisco WAP200 manual? We have 1 online manual for this item!
Question posted by tmpfesn on September 1st, 2014
Cisco Wireless-g Access Point Wap200 Cannot Connect To Config With Ethernet
cable
Current Answers
Related Cisco WAP200 Manual Pages
Administration Guide - Page 3
...Hardware overview 8 Front and rear panels 8 Antenna connectors 9 Ethernet port(s 9 Powering the WAP-200 9 Status lights 10 Radio...Wireless coverage 42 Wireless mode 42 Factors limiting wireless coverage 42 Configuring overlapping wireless cells 44 Conducting a site survey 48 Monitor mode 48 Identifying unauthorized access points 49
RF channel management 50 Operating mode 50 Wireless...
Administration Guide - Page 6
... type identifies menu selections, input fields, or user supplied values.
The term customer refers to install, configure, and operate the Colubris® Networks WAP-200 wireless access point.
Lead
Description
Warning! Typographical conventions
The following table explains some of the system.
6
You can either include them or not. Chapter 1 Introduction Chapter 1
About...
Administration Guide - Page 9
... connections must have reverse-polarity SMA female connectors.
Antennas can be used to either directly attached or attached through a coax cable. Transmit diversity
The WAP-200 always transmits on the antenna it is configured to operate as a DHCP client to Port 1 and the wireless port.
Ethernet port(s)
The WAP-200 has a single Ethernet port. DC...
Administration Guide - Page 19
... quality of networking environments. How it works
Chapter 2
How it works
This chapter describes the most important wireless connectivity challenges. The WAP-200 provides support for a wide range of service (QoS) Colubris® Networks MultiService Access points are highly-scalable solutions that offer leading-edge security and manageability features specifically designed for all MultiService...
Administration Guide - Page 20
....
20 As a satellite, the WAP-200 extends the wireless network and provides intelligent data-forwarding to maintain the security of an access controller-such as a satellite in a public access network. For detailed scenarios illustrating how the WAP-200 can be used as a stand-alone access point or as a Colubris Networks MultiService Controller-to manage customer...
Administration Guide - Page 31
... for WLAN name when they connect.
Therefore, the RADIUS server or access controller must communicate with the strongest signal. Egress VLAN
Choose the VLAN that your VLAN has the appropriate security installed to protect access to automatically discover access points that a VLAN may still be reachable via a setting in the wireless beacon. Also, a global VLAN settings...
Administration Guide - Page 36
... same group name to the wireless network.
• Block: All client stations whose MAC addresses appear in the MAC filtering list, MAC-based authentication is connected. Filter behavior
• Allow: Only client stations whose MAC addresses appear in the MAC address list can connect to more than one access point. The WAP-200 respects the...
Administration Guide - Page 39
...installed in through the public access interface provided by the access controller, rather, as soon as the family of the WAP-200 wireless port the customer is connected to the WAP-200. The...35 for each virtual service community, you to control logins to the public access network based on the wireless access point a customer is associated with 802.1x or WPA1/WPA2 client software. Important:...
Administration Guide - Page 42
.... Also, when multiple access points are using to determine how they will be able to receive signals from the access point, but they affect wireless coverage.
42
However, before...cell size needs to be able to reply, rendering the connection useless. Wireless mode
Available wireless modes are determined by the wireless radio installed in the WAP-200, and may include ...
Administration Guide - Page 43
... for this page for recommendations on using this problem. Such installations will require a separate wireless access point on all connected client stations. It also makes it easy to find rogue access points. This can effectively set your operating frequency. See for all wireless
access points operating in the immediate area so that operate in concrete walls and floors may...
Administration Guide - Page 44
...wireless cells
Overlapping wireless cells are caused when two or more access points are within range of your control (when your network.
Reset Reset
cell 1
cell 2
Overlapping wireless cells can cause a reduction in throughput in their own wireless... enables client stations connected to each other .
The following example shows two overlapping wireless cells operating on your...
Administration Guide - Page 45
.... Chapter 2 How it works Chapter 2
Selecting channels
For optimum performance when operating in 802.11b or 802.11g modes, choose a frequency that differs from other wireless access points operating in most regions is three.
To choose the best operating frequency, use the greatest separation possible between overlapping channels is very possible that the...
Administration Guide - Page 47
... feature.
Client stations will improve roaming performance.
For most installations, the Large setting should be beneficial to adjust the receiver sensitivity of wireless frequencies are configured with neighboring Colubris Networks access points.
47 Chapter 2 How it works Chapter 2
This strategy can be expanded to cover an even larger area using the same frequency...
Administration Guide - Page 48
... traced when using the Tools > Network trace command.
48 The WAP-200 will receive all active access points. Use this mode, both access point and wireless links functionality are disabled. See the results of other access points in your area, open the Wireless > Neighborhood page. The WAP-200 automatically scans to operate in all channels in monitor mode...
Administration Guide - Page 49
... so that are operating nearby. Therefore, it works Chapter 2
Identifying unauthorized access points
Improperly configured wireless access points can be identified as quickly as possible. List of authorized access points
The format of two items: MAC address and SSID. Each entry in the Unauthorized access points list.
When you edit the Brief list you must define).
Each entry...
Administration Guide - Page 50
... on the MAP-320, or by selecting Wireless > Radios on the Wireless > Neighborhood page. wireless client stations cannot connect.
• Monitor-Places the radio in all wireless functions.
• Access point only-Provides access point functionality only; wireless links cannot be created.
• Wireless links only-Provides wireless links functionality only; This mode also enables you...
Administration Guide - Page 52
...Select this option to use Distance between access points
Note: This option is selected, the WAP-200 can create a only single wireless cell using a small value for RTS threshold can affect throughput... connection, the WAP-200 always transmits on the link that using the radio.
• If a single antenna is not seen by the station. Packets smaller than one wireless access point installed...
Administration Guide - Page 58
... operate at the same time as the network serving wireless customers.
Each WAP-200 can support a single wireless bridge, which can also be used to other access points.
Customers are equipped with a directional external antenna and is impractical or expensive to run cabling to make the connection. In this configuration, both the WAP-200 and the...
Administration Guide - Page 59
... Controller, then access to the Management Tool across the bridge is blocked.
• As soon as a wireless bridge link is established, the spanning tree protocol is enabled on the link to provide proper routing of traffic.
• When using an external antenna (via a coax cable), it is recommended that you connect it works Chapter...
Administration Guide - Page 60
.... 3. Click Save. 8. Select Wireless > Radio. Set the Operating mode to have been configured, you may want to limit the speed of a link when connecting to set up a wireless link. 1. This is good. For...optimum bit rate. Open the Tools > Ping page on the wireless link.
6. Using the SNR value in
order to Access point and Wireless links. 10. A value greater than 20 is the most ...
Similar Questions
How To Configure Wap200 Access Point Multiple Ssid And Vlan
(Posted by Nicrdeleo 9 years ago)
How To Reset Wap200
(Posted by yvoam 9 years ago)
How To Factory Reset Cisco Wap200
(Posted by roydua 10 years ago)
How To Set Up Wap4410n Wireless-n Access Point - Poe/advanced Security For
separate ssid
separate ssid
(Posted by KiBr 10 years ago)
Can't Connect To Cisco Small Business Wap4410n
(Posted by planou 10 years ago)