Cisco CISCO2523LF - 2523LF Router Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco CISCO2523LF manuals!
Problems with Cisco CISCO2523LF?
Ask a Question
Free Cisco CISCO2523LF manuals!
Problems with Cisco CISCO2523LF?
Ask a Question
Popular Cisco CISCO2523LF Manual Pages
Getting Started Guide - Page 3
... power source is replaced incorrectly.
The 2504 controller comes with the same or equivalent type recommended by the manufacturer. As a component of the Cisco Unified Wireless Network (CUWN), the 2504 controller provides real-time communication between 32 to 104° F (0 to the manufacturer's instructions. The 2504 controllers supports up to provide system-wide wireless LAN...
Getting Started Guide - Page 4
... WCS software, web user interface
10/100/1000BASE-T MDI cable
Network
Distribution system connection
LAN link for management software connections
WAN or LAN connection to Cisco 2500 Series Wireless Controllers are not currently supported. Figure 1 shows a 2504 controller network topology and network connections, showing the medium dependent interface (MDI) Ethernet cables required. Note Direct...
Getting Started Guide - Page 5
... default settings of the ports and light-emitting diodes (LEDs) for the 2504 controller. however the bootloader ensures that there will default to unit. A default baud-rate recovery mechanism is an RS-232 port that supports a RJ-45 connector. Figure 2 Front Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model...
Getting Started Guide - Page 6
...so that 1500 VAC rms
isolation (per the 802.3 specification) is met between
chassis ground and any 48V/Ethernet signal. This interface supports the proper voltage isolation as defined by 802.3. LED ...The POE controller is driven from system reset. The POE controller reset is configured to I2C address 0x40/41 (0100 000r/w). The ports can do not connect access point devices to reset ...
Getting Started Guide - Page 9
... 2 Step 3
Open the shipping container and carefully remove the contents. Network, operating system service network, and access point cables as required • Command-line interface (CLI) console -
Package Contents
Each 2504 controller package contains the following items: • One Cisco 2504 Wireless Controller. • One Power supply and power cord (power cord option...
Getting Started Guide - Page 10
... name), such as rfgrp40 if required. The system name can contain up to 32 printable ASCII characters.
• An administrative username and password, which can contain up to clients and the management interface. • A virtual gateway IP address (a fictitious, unassigned IP address, such as 1.1.1.1, used by all Cisco
wireless controller Layer 3 security and mobility...
Getting Started Guide - Page 13
...hardware from Cisco.
Failure to...using the CLI setup program, see...installation:
• Connecting the Controller Console Port • Securing the Power Adapter Cable • Connecting to the system. Note Allow 3 inches of the 2504 controller as shown in Figure 5 with #10-32 flat head screws provided in a hazardous situation to people and damage to the Network
For configuration instructions...
Getting Started Guide - Page 24
... interface E - Run primary image (7.0.114.76) - Manually update images Enter selection:
If you did not press Esc, the...cisco) Board Revision 0.0 (SN: PSJ143302MT, Type: AIR-CT2504-K9) (P) Verifying boot loader integrity... Clear configuration 5.
Change active boot image 4. OK. Model... bootup script displays operating system software initialization (code download and POST verification)...
Getting Started Guide - Page 25
...Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok
25 Num of Cisco Systems, Inc. XML config selected...
Getting Started Guide - Page 27
... Software Copyright Cisco Systems, Inc. Manually update images
Enter selection...Cisco AireOS Version 7.0.114.76 Firmware Version PIC 14.0 Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Initializing Licensing Services: ok Starting ARP Services: ok Starting Trap Manager: ok Starting Network Interface Management Services: ok Starting System Services...
Getting Started Guide - Page 28
...Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services... AP Services: ok Starting AireWave Director: ok Starting Network Time Services: ok Starting Cisco Discovery Protocol: ok Starting Broadcast Services: ok Starting Logging Services: ok...
Getting Started Guide - Page 30
...default router. Table 3
Startup Wizard Information
Wizard Setting System Name Administrative user name
Administrative password
Action
Enter the system name, which is no default administrative password, ...port number of the controller and connectivity to enterprise services such as AAA servers.
Enter the administrative password to be set to this controller.
The management interface...
Getting Started Guide - Page 31
... authentication and VPN termination.
Although the name that the access points use when they have different purposes. Network Name (SSID)
Enter the network name, or service set identifier (SSID..., system-wide mobility and controller redundancy while an RF group facilitates scalable, system-wide dynamic RF management. This is the default SSID that you want the controller to support mobility...
Getting Started Guide - Page 34
... it by entering the config prompt command. Figure 13 External Network Equipment Connection to the Controller
10/100/1000BASE-T MDI cable
Cisco Access Points
CLI console
Connection to CISCO2504, enter config prompt "CISCO2504" and press Enter. You can change the system prompt to main office
Network
34
Firewall
Office network
10/100/1000BASE-T MDI...
Getting Started Guide - Page 35
... the controller, use a straight-through ) to connect access that are not currently
supported. When you are connecting to a hub or a switch, use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network (distribution system) as the controller is operational, the...
Cisco CISCO2523LF Reviews
We have not received any reviews for Cisco yet.