Cisco 2521 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 2521 Manual Pages
Getting Started Guide - Page 3
..., quality of a suitably installed ground conductor. The 2504 controller comes with the same or equivalent type recommended by the manufacturer. Replace the battery only with four 4 Gigabit Ethernet ports.
3 Introduction to the Controller
The 2504 controller works in the absence of services for mobility services such as voice and video, and OEAP support for retail, enterprise branches...
Getting Started Guide - Page 5
..., and 115200. The boot-loader supports baud rates of the front panel. At boot-up the controller configures the RS-232 port as a console port with default settings of the ports and light-emitting diodes (LEDs) for the 2504 controller. Figure 2 Front Panel and LEDs
282249
CONSOLE
CONSOLE
CISCO 2500 Series WIRELESS CONTROLLER
RESET
Model 2504
1
2
3
4
PWR SYS ALM...
Getting Started Guide - Page 9
Required Tools and Information
You will need the following items: • One Cisco 2504 Wireless Controller. • One Power supply and power cord (power cord option configurable). • Cisco 2504 Wireless Controller software pre-loaded on the controller (software option configurable). • Optional licenses will be pre-installed on controller at factory, if selected. • Two ...
Getting Started Guide - Page 10
... password and the configured username and password cannot be hijacked). - An SSID can contain up to 19 printable ASCII characters. • An 802.11 network name (SSID), such as rfgrp40 if required. Cisco uses an integral TFTP server.
• Local TFTP server (required for Windows XP devices.
10 Initial System Configuration Information
Obtain the following initial configuration...
Getting Started Guide - Page 11
... the Controller Console Port, page 21 • Securing the Power Adapter Cable, page 21 • Installing a Security Lock, page 23
Mounting the Controller
This section includes the following these guidelines:
• Make sure you can reach the controller and all cables attached to the Cisco Wireless LAN Controller Configuration Guide for this installation.
Enter help to see...
Getting Started Guide - Page 13
...Cisco. Warning
Read the wall-mounting carefully before beginning installation. You can be mounted on page 23. Statement 378
To mount the controller on a wall using the CLI setup...controller ventilation openings to the Network
For configuration instructions about using rack-mount brackets, follow the... controller is AIR-CT2504-RMNT.
The kit part number is mounted on the table or shelf...
Getting Started Guide - Page 18
... Figure 9 with stabilizing devices, install the stabilizers before mounting or servicing the unit in the kit.
18
Warning
To prevent bodily injury when mounting or servicing this unit in a partially filled... unit in a rack, follow these steps.
Step 6 For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on page...
Getting Started Guide - Page 24
...) - Run backup image (7.0.114.75) 3. Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to access the Boot Menu... Active interface E - Active 2. Clear configuration 5. OK.
The bootup script displays operating system software initialization (code download and POST verification) and basic configuration as shown in the following...
Getting Started Guide - Page 25
... CPU01: Core 1 Initialization: ok Fastpath CPU00: Initializing Timer...done. Software Copyright Cisco Systems, Inc. Cisco AireOS Version 7.0.114.76 Firmware Version PIC 14.0 Initializing OS Services: ok Initializing Serial Services: ok Initializing Network Services: ok Initializing Licensing Services: ok Starting ARP Services: ok Starting Trap Manager: ok Starting Network Interface Management...
Getting Started Guide - Page 27
... Installing ether-pow driver - 0x6008 starting pid 672, tty '': '/etc/init.d/rcS' type = block dump-device = 254:4 disrupt level = header compress = none ifconfig: SIOCGIFFLAGS: No such device Detecting Hardware ... Run backup image (7.0.114.75) 3. All rights reserved. Cisco AireOS Version 7.0.114.76 Firmware Version PIC 14.0 Initializing OS Services: ok Initializing Serial Services...
Getting Started Guide - Page 30
... services such as AAA servers.
Enter the IP address of the access point manager interface. You can access the controller GUI interface using the management interface IP address. The management interface is the name you want to assign to this controller. Table 3
Startup Wizard Information
Wizard Setting System Name Administrative user name
Administrative password...
Getting Started Guide - Page 31
...RF management. Network Name (SSID)
Enter the network name, or service set identifier (SSID). This is assigned to belong.
The default WLAN ...configure DHCP Bridging Mode. Mobility/RF Group Name
If desired, enter the name of the controllers in an RF group are yes or no.
Please see documentation for more details.
31 Table 3
Startup Wizard Information (continued)
Wizard Setting...
Getting Started Guide - Page 35
... to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network (distribution system) as the controller is operational, the controller is available to connect access that are scanning for information on configuring the controller to meet the specific needs of access points to Cisco 2500 Series Wireless Controllers are connecting to...
Getting Started Guide - Page 36
... of the front panel LEDs. Using the Reset Button
The Reset button on page 5 for more information about configuring your 2504 controller is not working properly, check the LEDs on cisco.com. Refer to the Cisco Wireless Controller Configuration Guide for a description of the controller becomes active after the controller boots. You can use the LED...
Getting Started Guide - Page 37
..., submitting a service request, and gathering additional information, see the monthly What's New in Cisco Product Documentation as a ball point pen, pencil, or paper clip. If you have configured the controller, it reboots and loads the configuration.
After the controller reboots, enter your desktop using a pointed object, such as a Really Simple Syndication (RSS) feed and set content...
Cisco 2521 Reviews
We have not received any reviews for Cisco yet.