Carvin MX641 Support and Manuals
Get Help and Manuals for this Carvin item
View All Support Options Below
Free Carvin MX641 manuals!
Problems with Carvin MX641?
Ask a Question
Free Carvin MX641 manuals!
Problems with Carvin MX641?
Ask a Question
Popular Carvin MX641 Manual Pages
Instruction Manual - Page 1
ESCONDIDO, CA 92025 TOLL-FREE: (800)854-2235 CARVIN
MX621 & MX641 RACK MOUNT MIXERS
MX601 SERIES CONSOLE MANUAL
REVISED 2/16/88
1155 INDUSTRIAL AVE.
Instruction Manual - Page 3
... Mixer! * Facts About Use * Precautions * Procedures Before Turning On Unit
SECTION III * Front Panel Features * Rear Panel Features
SECTION IV * Connections to the Unit
SECTION V * Servicing In Your Area * Factory Servicing * Warranty Requirements * Service Authorization Form
SECTION VI " Specifications * Schematic & Technical Information
1-2 3-7
8-17 18 19-21 22-23
Instruction Manual - Page 6
...Always check your invoice against the items you receive all the items in the event such servicing is necessary. If you determine (after allowing an appropriate amount of your unit in your...TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNIT TO RAIN, MOISTURE, EXPLOSIVE ATMOSPHERE, OR INSTALL AN IMPROPER FUSE. Questions? If you have received.
It will be that you have not received...
Instruction Manual - Page 7
...a great plus in a rack package. As a mixer for both models as the MX641. Additionally, if you will accept high impedance instrument ... model delivers 200 watts rms into a two ohm load (150 watts into a four ohm load)! PLEASE NOTE: For simplicity, the manual will...MOUNT MIXERS
MODELS: MX621,MX641
The MX601 series mixers are professional rack mountable consoles with built-in two models: MX621 and...
Instruction Manual - Page 8
...The MX641 series mixers are reliable rotary potentiometers. This equalizer will allow you for servicing or replacement. The patch section of this mixer. It will provide a responsive tool for ... are reliable, high quality performance mixers. They will allow precise adjustments to provide you support of this patch panel as well as a professional musician.
2-4 Its summing accuracy and...
Instruction Manual - Page 9
... should be fuse protected. Each speaker should be NON-SHIELDED. One of the 1/4" phone speaker jack). All grounding is done through the ground lug of trouble free performance. THIS IS TO PROVIDE THE BEST MARGIN OF SAFETY AND PERFORMANCE FROM YOUR AMP.
5. If the unit is going to the "red" terminal...
Instruction Manual - Page 15
... monitors as well by the channel volume control) to the problem.
5.
Any channel volume changes will control the level of .... For instance, you will select the desired monitor level of a specific range. It will allow you are usually the most natural tone. ...signal that when the channel volume is OFF, so is used to set the level (per channel) of "feel" for the most susceptible to...
Instruction Manual - Page 16
... feature--you may wish to experiment with respect to each of each channel with various effects to your effect its input level control. B. You will set the relative levels of these signals simultaneously.
Instruction Manual - Page 17
... of the MX641. PWR AMP IN connection.
3-12 To achieve this control should be adjusted in addition to have two different effects at a slightly lower setting than the main mix on the patch section of the internal reverb system for equalizing other signals (other than the channel monitor level controls.
C. This...
Instruction Manual - Page 19
... using the graphic equalizer.
3-14 Graphic equalizers are more sophisticated methods of electronically setting your equalizer for your ear using the graphic equalizer will probably find that suits your...of the equalizer. Experimentation and use than a standard three band equalizer, and that setting up your system, you should then make the appropriate adjustments on each channel to...
Instruction Manual - Page 21
... selected.
The voltage that will provide an extra margin of safety and reliability for your mixer from the value listed on the MX641 (higher powered) model. There are wired in parallel. A.C. Also, recommended is the main A.C. source produced by inserting a small screwdriver and moving the switch to 120V, 50Hz or 60Hz...
Instruction Manual - Page 25
...(Switched Leg) LO (Neutral) EARTH (Chassis Ground)
Black White Green w/Yellow Tracer
2. The color code of accepting impedances from long cable runs, while electronic balancing helps to the XLR or 1/4" phone plug...XLR input is accommodated by all standard 3-pin American sockets. The MX641 model console has dual voltage capability 120V/220V. SECTION IV CONNECTIONS TO THE MX641 MIXER
INPUT CONNECTIONS
1....
Instruction Manual - Page 27
... factory specifications.
It you do not involve yourself in this manual.
2.
IF YOU ELECT TO HAVE YOUR OWN SERVICING DONE, THESE BILLS MUST BE PAID BY THE CUSTOMER.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN, MOISTURE, EXPLOSIVE ATMOSPHERE OR INSTALL AN IMPROPER FUSE!
Regardless of improper servicing or component replacement. Please...
Instruction Manual - Page 28
... of warranty, you will be charged a modest fee (generally lower
than typical repair shops). Please allow five working days for servicing plus shipping time to represent or assume for ONE YEAR. No representative or person is in its products and specifications without notice or obligation.
5.20
This warranty is authorized to and from...
Instruction Manual - Page 29
TECHNICAL SPECIFICATIONS
Frequency Response Mic or line inputs: 20 Hz-20KHz ±1 dB
Total Harmonic Distortion Mic in ...80 dBv
Master controls nominal w; -75 dBv Channel controls minimum: (non-powered models)
-80 dBv (powered models) Master controls nominal WI -82 dBv one channel set for 40 dB gain. -79 dBv (powered models)
Crosstalk
Adjacent channels: -60 dB at lkHz -50 dB at 10kHz
Common ...
Carvin MX641 Reviews
We have not received any reviews for Carvin yet.