Carvin MX621 Support and Manuals
Get Help and Manuals for this Carvin item
View All Support Options Below
Free Carvin MX621 manuals!
Problems with Carvin MX621?
Ask a Question
Free Carvin MX621 manuals!
Problems with Carvin MX621?
Ask a Question
Popular Carvin MX621 Manual Pages
Instruction Manual - Page 1
CARVIN
MX621 & MX641 RACK MOUNT MIXERS
MX601 SERIES CONSOLE MANUAL
REVISED 2/16/88
1155 INDUSTRIAL AVE. ESCONDIDO, CA 92025 TOLL-FREE: (800)854-2235
Instruction Manual - Page 3
... * About the MX621 & MX641 Series Consoles * Read Before Using Your New Mixer! * Facts About Use * Precautions * Procedures Before Turning On Unit
SECTION III * Front Panel Features * Rear Panel Features
SECTION IV * Connections to the Unit
SECTION V * Servicing In Your Area * Factory Servicing * Warranty Requirements * Service Authorization Form
SECTION VI " Specifications * Schematic & Technical...
Instruction Manual - Page 6
...) that you have not received all your items, please call Carvin in the event such servicing is necessary. It will be that we may take the necessary steps to arrive before inquiring...DO NOT EXPOSE UNIT TO RAIN, MOISTURE, EXPLOSIVE ATMOSPHERE, OR INSTALL AN IMPROPER FUSE. Questions? Please allow several days for warranty servicing of your order to assure that you receive all the items in...
Instruction Manual - Page 7
... the same time. PLEASE NOTE: For simplicity, the manual will allow you can have this control can allow you... a compact size without a lot of boost and cut. The MX621 model delivers 200 watts rms into a two ohm load (150 watts ... powered allowing the console to -noise ratios (over 15dB range of setup hassles. Each channel also features a separate Effects/Reverb send control. ...
Instruction Manual - Page 8
... it may be used in rack mountable mixers. It has auxiliary inputs to allow you support of modern mechanical and electronic design. Each channel of this patch panel as well as...to radio frequency interference and maintains best signal-to establish the appropriate levels for servicing or replacement. All internal electronic circuitry is also "patchable". The graphic equalizer is designed ...
Instruction Manual - Page 9
... dusted and free from the amp. lines are plugging the amp into the proper A.C. All speaker wires should be in excessive heat build-up of trouble free performance. The high power output capability of the three conductor A.C. plug. If for your mixer.
4. Be sure the voltage is done through the ground...
Instruction Manual - Page 14
... best overall performance from both high and low impedance input Aignals. "hum" can be set the level of these volumes higher than the master volume. This means that any potential ...loudness) of the console is low impedance (allowing for the best possible performance. Typically you to set with respect to -noise ratio.
3.9 Line level (or preamp level) signals typically range from ...
Instruction Manual - Page 15
... control) to the internal reverb system. This means that will establish the overall level of a specific range. This is done because the control is a "prefader" signal that a tone control adjusts... to a different microphone, or changing the angle (or proximity of a channel relative to the problem.
5. The Effects Send Control is used to the internal reverb system or an external effect.
...
Instruction Manual - Page 17
... tape deck connected to the TAPE IN connections, but remember to return your mix. You may wish to have two different effects at a slightly lower setting than the main mix on the Master Control Section.
2.
As with the effects send level. The output of the effect by the EQ OUT connection...
Instruction Manual - Page 19
... tonal response of your speaker system. This is usually the final judge of electronically setting your ear. Then experiment with their "graphic representation" of the volume level of various frequency bands....overall sound. At this feature is the key to you will ultimately offer the most uniform mix. Set each of the bands at "0" and boost/cut each band one at a time to become familiar...
Instruction Manual - Page 21
...from further damage.
LINE FUSE - If your main level control "OFF" when turning on the MX641 (higher powered) model. You should have your mixer should never attempt to the appropriate position.
5. NOTE: If you check the A.C. power ... Shielded cables (such as guitar cords) can cause high performance amplifiers (as follows:
MX621
3 amp
MX641
5 amp
4. 120V/240V SWITCH-
Instruction Manual - Page 25
...is as follows:
HI (Switched Leg) LO (Neutral) EARTH (Chassis Ground)
Black White Green w/Yellow Tracer
2.
The color code of the MX601 series mixers. "XLR TYPE BALANCED INPUT"- The A.C.
main voltage should be using microphone cables that you may ...
LINE LEVEL OUTPUT OF CONSOLE
TO "LINE IN" OF TAPE DECK
4-18 The MX641 model console has dual voltage capability 120V/220V.
Instruction Manual - Page 27
... ONE YEAR WARRANTY, Garvin will ship parts pre-paid to make necessary repairs faster, and for our inspection. Also, you may select your own service center or have your unit serviced locally, we ask that the defective part(s) are glad to factory specifications. REMINDER: CARVIN DOES NOT PAY FOR SERVICING OR PARTS OTHER THAN OUR OWN - IF YOU...
Instruction Manual - Page 28
... USE.
CARVIN WILL NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. This warranty...responsibility for Carvin any horn driver speaker damaged by AIR, you will service the unit, supply all ...repair shops). A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Garvin takes no charge to represent or assume for any liability in its products and specifications...
Instruction Manual - Page 29
... (non-powered models)
-80 dBv (powered models) Master controls nominal WI -82 dBv one channel set for 40 dB gain. -79 dBv (powered models)
Crosstalk
Adjacent channels... 3-pin XLR type
Input impedance: 3k S2 (balanced) Source impedance. TECHNICAL SPECIFICATIONS
Frequency Response Mic or line inputs: 20 Hz-20KHz ±1 dB
Total ...MX621 120V, MX641 120 240V
Warranty
1 year parts and labor
CARVIN
Carvin MX621 Reviews
We have not received any reviews for Carvin yet.