Users Manual - English
Page 19
... models equipped with the start /stop button). Put the bobbin onto the bobbin winder shaft h and slide the bobbin winder shaft to the right. k • Leave 1 cm (3/8 inch) of thread from the hole on the bobbin. 1 a 1 cm (3/8 inch) CAUTION ● Make sure you do not cut the thread completely, and ... not pulled taut or held at an angle, injuries 1 may not be used to start sewing (only for models equipped with the start/stop button cannot be wound cleanly. Note ● If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on...
... models equipped with the start /stop button). Put the bobbin onto the bobbin winder shaft h and slide the bobbin winder shaft to the right. k • Leave 1 cm (3/8 inch) of thread from the hole on the bobbin. 1 a 1 cm (3/8 inch) CAUTION ● Make sure you do not cut the thread completely, and ... not pulled taut or held at an angle, injuries 1 may not be used to start sewing (only for models equipped with the start/stop button cannot be wound cleanly. Note ● If the sewing machine is to be operated using the foot controller, connect the foot controller before turning on...
Users Manual - English
Page 54
... X The size of 10 mm (3/8 inch), the button guide plate should be set . 52 d Pass the upper thread down through the hole e in the button guide plate Add together the diameter and thickness of the button, and then set the button guide plate to the calculated length. (The distance between ...the markings on the presser foot scale is 5 mm (3/16 inch).) 1 3 4 A a Button guide plate b Presser ...
... X The size of 10 mm (3/8 inch), the button guide plate should be set . 52 d Pass the upper thread down through the hole e in the button guide plate Add together the diameter and thickness of the button, and then set the button guide plate to the calculated length. (The distance between ...the markings on the presser foot scale is 5 mm (3/16 inch).) 1 3 4 A a Button guide plate b Presser ...
Users Manual - English
Page 57
...is the same as seen from the front of the machine on with 4 holes can be sewn on the base, to (to the right as f the distance between the holes in the a button to be attached. Button sewing Buttons can be attached. Raise the presser foot lever, and then slide the ...b feed dog position lever, located at the rear of the machine). • When attaching four-hole buttons, first sew the two holes closest to the shortest setting...
...is the same as seen from the front of the machine on with 4 holes can be sewn on the base, to (to the right as f the distance between the holes in the a button to be attached. Button sewing Buttons can be attached. Raise the presser foot lever, and then slide the ...b feed dog position lever, located at the rear of the machine). • When attaching four-hole buttons, first sew the two holes closest to the shortest setting...
Users Manual - English
Page 58
... ● When sewing, be sure that the needle correctly goes into the two holes of the button. Pull the upper thread at low speed, press (reverse/reinforcement stitch button) to sew reinforcement stitches. UTILITY STITCHES Turn the handwheel toward you are finished attaching... the button, k slide the feed dog position lever to (to the left as seen from the front... thread and the bobbin thread at . 56 When you h (counterclockwise) to the distance between the button holes.
... ● When sewing, be sure that the needle correctly goes into the two holes of the button. Pull the upper thread at low speed, press (reverse/reinforcement stitch button) to sew reinforcement stitches. UTILITY STITCHES Turn the handwheel toward you are finished attaching... the button, k slide the feed dog position lever to (to the left as seen from the front... thread and the bobbin thread at . 56 When you h (counterclockwise) to the distance between the button holes.
Users Manual - English
Page 68
...02 02 ing inseams, sewing stretch fabrics and deco- Attach buttonhole foot "A". CAUTION ● Be sure to strain, such as sleeve holes, inseams and pocket corners. Triple stretch stitching Use triple stretch stitching to strain, such as pocket corners and openings. Rfc. * Auto... Rfc. b Select stitch . UTILITY STITCHES REINFORCEMENT STITCHING Reinforce points that will be sewn. Otherwise, injuries may occur if the foot controller or (start/stop button) is described below. 2 3 a Presser foot scale b Length of bar tack c 5 mm (3/16 inch) • A bar tack with a ...
...02 02 ing inseams, sewing stretch fabrics and deco- Attach buttonhole foot "A". CAUTION ● Be sure to strain, such as sleeve holes, inseams and pocket corners. Triple stretch stitching Use triple stretch stitching to strain, such as pocket corners and openings. Rfc. * Auto... Rfc. b Select stitch . UTILITY STITCHES REINFORCEMENT STITCHING Reinforce points that will be sewn. Otherwise, injuries may occur if the foot controller or (start/stop button) is described below. 2 3 a Presser foot scale b Length of bar tack c 5 mm (3/16 inch) • A bar tack with a ...
Users Manual - English
Page 95
...lever. Correctly install the needle. Use the disc-shaped screwdriver to the left. page 31 The needle is turned off. The area around the hole in the needle plate is incorrectly Correctly install the spool or spool installed. Turn on the main power switch. page 88 4 be removed.... the presser foot that is connected. Loosen the upper thread tension. Replace the presser foot. page 15 93 page 39 The start/stop button was pressed, even though the foot controller is not plugged in . The spool or spool cap is scratched. page 24 The upper thread...
...lever. Correctly install the needle. Use the disc-shaped screwdriver to the left. page 31 The needle is turned off. The area around the hole in the needle plate is incorrectly Correctly install the spool or spool installed. Turn on the main power switch. page 88 4 be removed.... the presser foot that is connected. Loosen the upper thread tension. Replace the presser foot. page 15 93 page 39 The start/stop button was pressed, even though the foot controller is not plugged in . The spool or spool cap is scratched. page 24 The upper thread...
Users Manual - English
Page 100
...63 quilting foot 64 , quilting guide 63 64 R race 80 reinforcement stitching 40 , reverse/reinforcement stitch button 9 40 S scallop stitching 70 seam ripper 54 sewing machine needles 29 , sewing speed controller 9 13 sleeve holes 66 smocking 70 spool cap 6 10, 15, 24 spool , pin 10 15, 23 , start.../stop button 9 39 stitch length 38 stitch selection key 10 stitch settings 73 stitch width 38 straight ...
...63 quilting foot 64 , quilting guide 63 64 R race 80 reinforcement stitching 40 , reverse/reinforcement stitch button 9 40 S scallop stitching 70 seam ripper 54 sewing machine needles 29 , sewing speed controller 9 13 sleeve holes 66 smocking 70 spool cap 6 10, 15, 24 spool , pin 10 15, 23 , start.../stop button 9 39 stitch length 38 stitch selection key 10 stitch settings 73 stitch width 38 straight ...