Brother International BE-1206B Support and Manuals
Get Help and Manuals for this Brother International item
This item is in your list!
View All Support Options Below
Free Brother International BE-1206B manuals!
Problems with Brother International BE-1206B?
Ask a Question
Free Brother International BE-1206B manuals!
Problems with Brother International BE-1206B?
Ask a Question
Popular Brother International BE-1206B Manual Pages
Thread Tensions - English - Page 1
...use genuine Brother parts.
1. Spin Spring for the correct weight), in the Brother bobbin ...problem, but with open side up again. At installation of the fabric and reduce thread breaks. This helps slow down on Brother...guide. Re-insert the spring and recheck your adjustment. It is used to replace it will help with two cardboard sides that they do make a difference. Install...
Thread Tensions - English - Page 2
...install and at which the tension spring will have erratic tensions looking
tensions of the backside of the anti-spin spring while setting...of backing, rub
underneath the spring to replace the use of the bobbin. Part # BTG3
When inserting the bobbin into the...
!" When do this over
or the bobbin could be the problem,
ALWAYS check and adjust bobbin first if necessary.
You
may ...
Thread Tensions - English - Page 3
Run a tension test first, if you are still having trouble check the thread path and rethread the complete path for individual needle tail lengths ... to three turns, then there may be something else that needs to view outcome of adjustment.
3 At installation and for any tension problems after removing & cleaning them ? What are they for ? Thread Tree Tensioners
!" To take the looseness ...
Thread Tensions - English - Page 4
... you adjust them ? Make sure that the thread is moving into position to polish up lever eyelet is one of the main areas of thread guide tension problems. The surface of the eyelet may be come tarnished from metallic thread or the environment, causing a dramatic increase in the thread path and is...
Thread Tensions - English - Page 5
...one turn it , then all just guidelines to setting tensions and correcting tension problems. The first thing to always do once the bobbin has been set to become wider on the thread. This is...the bottom of needles your bobbin tension when replacing the bobbin. Is it does not move. You may want to the best of your ability.
!" Usually found is set the anti-spin spring and try again.
...
Maintenance Schedule - English - Page 9
...models, just remove the X-feed cover R [2] only.
2. Feed Guide Section 1. Unscrew the screw [1] and remove the X-feed
covers R [2] and L [3]. BE-1204, 1206
For Technical Assistance Please Call Toll Fre e 1-877-4BROTHER Email: tsupport@brother.com
Website: http://www.brother...X-feed linear guide parts (2 positions) and Y-feed linear guide parts (2 positions), and slide those parts to spread the...
Tubular to Cap - English - Page 1
...driver... and lower on your machine model. BE-1204B/BE1206B -
Push up on the ...cap frame sash so that hold on .
3. Do this to the machine OFF.
1. Remove the pair of the tubular arms and them remove the arms.
BE-1204C - BE-1204, 1206
For Technical Assistance Please Call Toll Fre e 1-877-4BROTHER Email: tsupport@brother.com
Website: http://www.brother...
Changing Needle Bar Cushions - English - Page 1
...:
Changing needle bar cushions
Models: BE-1204C, BE-1206B
1. Remove the covers between each head by removing the two lower screws and loosening the one upper screw on the cover behind the head.
1 Make sure the machine power is turned off. 2.
Remove Loosen
4. Plus removing a screw on the BE-1206.
3. Remove the right...
Rotary Hook Support Bar - English - Page 1
... screws as indicated by the red arrows and remove the rotary hook support bar.
Install new rotary hook support bar but this is not necessary. The screw head for the left... Hook Support Bar Remove
4. Using red T-handle (4mm) wrench, turn pulley in the photo, but leave the screws slightly loose.
1 Technical Reference
Title: Date: Models:
Adjusting / Replacing rotary hook support bar ...
Rotary Hook Support Bar - English - Page 2
Rotary Hook Support Bar Tip
Remove
7. Position tip of rotary hook stopper so that a gap of approximately 1 - 1.5mm is maintained from 200 to
100 degrees (stop position). 9. Middle thread guide
Remove
Loosen
Remove
.... Align the tip of arrow, from rotary
hook bobbin basket as indicated by the thread guide above the needle, until it locks into place. Turn machine on and the needle will ...
Procedure for sewing a DST file using PC - English - Page 1
..., BE-1204-PC, BE-1206-PC BES-960, BES-962, BES-1240, BES-1260, BES-1262
Preparation
1. Embroidery Cancel icon Cancelling previous design
1.
Machine Reference
Title: Date: Models:
Procedures for sewing a DST file using a USB flash drive or floppy disk please insert in to the computer. Turn on the Brother embroidery machine.
(Note...
Procedure for sewing a DST file using PC - English - Page 6
Left click on "Settings".
Loading embroidery hoop to use
(Note: If using some aftermarket hoops, such as a FastFrame, this step is optional.)
1.
Left click on "Load Hoop". Settings
2. Load Hoop
Procedure for sewing a DST file using PC - English - Page 7
There are listed under C:\Program Files\BES-960.) • HOOP - Please use the correct folder for your model. See below:
(Note: These two folders are two folders containing hoop outlines, Hoop and Hoop2. BE-1204-PC, BE-1206-PC
4. Double left click on a hoop filename to load. BE-0901-PC, BE-1201-PC, BES-960, BES-962, BES-1240, BES-1260, BES-1262 • HOOP2 - 3.
Procedure for sewing a DST file using PC - English - Page 9
Left click on the "Needle Bar Change" icon.
The "Needle Bar Change" window appears. Setting color sequence
1. Needle Bar Change icon
2.
Procedure for sewing a DST file using PC - English - Page 12
Left click on the "Down" button to adjust if needed.
(Note: 800spm for tubular and 700spm are good speed ranges to the fastest "Speed Range". All DST files loaded in to the software will default to start with.)
Speed range information Speed adjustment buttons Setting sewing speed
1.
Brother International BE-1206B Reviews
Do you have an experience with the Brother International BE-1206B that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Brother International yet.
Earn 750 points for your review!