BenQ PE7800 - DLP Projector - 800 ANSI Lumens Support and Manuals
Popular BenQ PE7800 Manual Pages
User Manual - Page 4
... Menu 23 DISPLAY Menu 24 ENVIRONMENT Menu 26 INSTALLATION Menu 27 PRO-PICTURE Menu 28
Additional Information 30
Warning Message 30 Replacing the Lamp (Contact your BenQ dealer for assistance 31 Indicators ...32 Troubleshooting 33 Specifications ...34
Optical Characteristics ...34 Electrical Characteristics ...34 Input/Output ...34 General Characteristics ...34
Dimensions ...35
4 Table...
User Manual - Page 5
...manual... Part...servicing) instructions in a particular installation...guide through the control menus and operation. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. Connect the equipment into an outlet on , the user is asked to beware of this equipment does cause harmful interference to comply with the instructions, may cause electric shock. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS...
User Manual - Page 6
... not look straight at the projector lens during operation. There are no user serviceable parts inside.
• Refer servicing to operate
safely with a mains voltage between 100 and 240
volts AC, but could fail if power cuts or surges of information technology equipment . This projector is important that you follow the instructions mentioned in this product, it...
User Manual - Page 7
... to a qualified
approximately 45 minutes prior to fail or result in fire. This product is required. The lamp becomes extremely hot during
5. The product may cause damage to the lamp, the projector to removing the
technician when service or repair is capable of electric shock, do not
operation.
Safety Instructions
Safety Instructions
1. Take it is subsequently used.
2.
User Manual - Page 8
... it from the power supply's wall socket and call
BenQ to have rubber or plastic products touching the projector for a long ...projector. Using the unit when it is a sudden change in lamp. Disposal
This product contains the following 10. environments.
-
Moisture Condensation
Never operate the projector immediately after moving it .
9. Do not have the projector serviced...
User Manual - Page 9
... 6-segment color wheel, the projector can support a wide variety of up...installations that have longer cables. The sealed optical engine prevents light leakage and any dust from entering the engine, which provides dynamic performance and rich gray-scale without the 'color flicker' or 'rainbow effect' associated with 3:2 Pull-Down Using BenQ's proprietary de-interlacing technology, the projector...
User Manual - Page 10
Projector
User's manual User's manual CD Warranty card
Batteries
BNC-RCA adapter 12V DC-plug
Remote control
US (110V)
EU (220V) Power cord
UK (240V)
Component video cable
S-Video cable
D-Sub - Q Do not mix an old battery with the correct polarity, then close the cover. If any of these items are correct when installing the batteries...
User Manual - Page 13
... to page 20 and 26 for more information.)
9. information.)
Adjusts the focus of lamp. Q The orange light shows when the AC power cord is
Exits and saves the menu settings. Shows a red light when the lamp has developed a problem.
lamp is cooling.
5. LAMP indicator light (Refer to page 23 for more information.)
10. operating. Indicates the status...
User Manual - Page 14
...turn the projector on. These functions are only available for more information.) SCREEN c / d: Control the screen up to turn the projector off . (Refer to page 23 for more information.)
Picture quality adjustment... default settings for the current input source. (Refer to page 26 for more information.)
EXIT Exits and saves any changes made using the menu. (Refer to page 23 for BENQ's accessory...
User Manual - Page 19
...' zoom ring. The ON key on the remote control and the POWER key on the projector may directly select the input source by rotating the focus ring.
Q You may not work while the projector is cooling. (The Power light blinks orange while the projector is turned on -screen until a valid signal is detected.
4. If the...
User Manual - Page 21
... setting in the active
window. Q Adjust the position of the PIP window. Press the OFF key on the remote control or the POWER key
on the projector. 2. PIP (Picture-In-Picture)/POP (Picture-On-Picture...) functions
Q Press the PIP button to enable the PIP function. 1.For PIP purposes, there are only available for BENQ's...
User Manual - Page 26
... after the lamp has been replaced. 3. LAMP TIMER: Resets the lamp timer. POS.: Adjusts the vertical position of signal.
4. SAVE: There are three video memories in which users can store settings, including all items in the Picture and Pro-Picture menus to a value between10 minutes and 3 hours. 4. ENVIRONMENT Menu
In this menu, global settings for the projector can be...
User Manual - Page 31
... broken glass to reset the "Lamp Timer" item. ■ Power will not light, even after the lamp is off the lamp shield.
5. Do not insert your BenQ dealer for assistance)
CAUTION: The lamp may be reset as soon as a new lamp is installed.
■ Do not reset the lamp life without replacing the lamp.
Pull out the lamp module horizontally.
Tighten the...
User Manual - Page 33
... on the remote control. Remedy
Plug the power cord into to a cooler loaction. Correctly attach the front lamp cover. Select the correct input signal. The video source is no power from the power cable. The input signal has not been correctly selected. Troubleshooting
Problem
The projector does not turn the projector on and check that it is not...
BenQ PE7800 Reviews
Do you have an experience with the BenQ PE7800 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for BenQ yet.
Earn 750 points for your review!