User's Manual for English Edition
Page 1
... an HDMI device If you want to use a high-definition TV as an audio output device, connect it to your previous operating system, read the system requirements below before upgrading to Windows® 8: Processor RAM Hard disk space Graphics card Screen resolution 1GHz or faster 1GB (32-bit) or 2 GB (64-bit) 16 GB (32-bit) or 20 GB (64-bit) Microsoft DirectX9 graphics device with WDDM driver 1024...
... an HDMI device If you want to use a high-definition TV as an audio output device, connect it to your previous operating system, read the system requirements below before upgrading to Windows® 8: Processor RAM Hard disk space Graphics card Screen resolution 1GHz or faster 1GB (32-bit) or 2 GB (64-bit) 16 GB (32-bit) or 20 GB (64-bit) Microsoft DirectX9 graphics device with WDDM driver 1024...
User's Manual for English Edition
Page 2
Click Finish to do a normal shutdown. • From the log-in screen, tap > Shut down. • If your All-in-one PC is unresponsive, press and hold the power button for at least four (4) seconds until your All-in-one PC turns off. Select Stereo and click Next. 6. 5. Tick the Front left and right option, and click Next. 7. Turning your All-in-one PC off Do any of the following to shut down your All-in-one PC: • Tap from the Charm bar then tap > Shut down to exit the speaker setup.
Click Finish to do a normal shutdown. • From the log-in screen, tap > Shut down. • If your All-in-one PC is unresponsive, press and hold the power button for at least four (4) seconds until your All-in-one PC turns off. Select Stereo and click Next. 6. 5. Tick the Front left and right option, and click Next. 7. Turning your All-in-one PC off Do any of the following to shut down your All-in-one PC: • Tap from the Charm bar then tap > Shut down to exit the speaker setup.
User's Manual for English Edition
Page 3
... the power button for at least four (4) seconds to access the BIOS directly. • Press the power button for system startup in your All-in-one PC. Inappropriate BIOS settings may result to instability or boot failure. We strongly recommend that run when you turn on your All-in-one PC. WARNING! NOTE: POST (Power-On Self Test) is a series of software controlled diagnostic tests that you change the BIOS settings only with...
... the power button for at least four (4) seconds to access the BIOS directly. • Press the power button for system startup in your All-in-one PC. Inappropriate BIOS settings may result to instability or boot failure. We strongly recommend that run when you turn on your All-in-one PC. WARNING! NOTE: POST (Power-On Self Test) is a series of software controlled diagnostic tests that you change the BIOS settings only with...
User's Manual for English Edition
Page 4
... to enter a security key to start the network connection. Turn on sharing and connect to devices. Wi-Fi connection To set up your wired connection: 1. Wired connection To set up your Wi-Fi connection: 1. c) Select an access point from your All-in-one PC to a DSL/cable modem or a local area network (LAN). 2. Tap No, don't turn on your All-in-one PC: a) Launch the Charm bar. Configure the necessary Internet connection settings. Connecting to the Internet Access...
... to enter a security key to start the network connection. Turn on sharing and connect to devices. Wi-Fi connection To set up your wired connection: 1. Wired connection To set up your Wi-Fi connection: 1. c) Select an access point from your All-in-one PC to a DSL/cable modem or a local area network (LAN). 2. Tap No, don't turn on your All-in-one PC: a) Launch the Charm bar. Configure the necessary Internet connection settings. Connecting to the Internet Access...
User's Manual for English Edition
Page 5
... Set up a new connection or network. 8. Click the network icon in the taskbar and click the connection you are using PPPoE connection. 7. Configuring a dynamic IP/PPPoE network connection To configure a dynamic IP/PPPoE or static IP network connection: 1. Enter your User name, Password, and Connection name. When done, click OK. Enter your user name and password. Return to the Internet and click Next. 9. Repeat steps 1 to launch the Desktop mode. 2. From the Metro Metro Start Screen...
... Set up a new connection or network. 8. Click the network icon in the taskbar and click the connection you are using PPPoE connection. 7. Configuring a dynamic IP/PPPoE network connection To configure a dynamic IP/PPPoE or static IP network connection: 1. Enter your User name, Password, and Connection name. When done, click OK. Enter your user name and password. Return to the Internet and click Next. 9. Repeat steps 1 to launch the Desktop mode. 2. From the Metro Metro Start Screen...
User's Manual for English Edition
Page 6
... its factory default settings. Back up all your USB storage device will be permanently deleted during bootup. 2. Select Only the drive where the Windows is installed. 6. Click Next. Press during the process. From the screen, click Troubleshoot. 3. From the Control Panel's System and Security, click Find and fix problems. 3. To create a USB recovery drive: 1. Recovering your system Resetting your All-in-one PC The Reset your PC option restores your...
... its factory default settings. Back up all your USB storage device will be permanently deleted during bootup. 2. Select Only the drive where the Windows is installed. 6. Click Next. Press during the process. From the screen, click Troubleshoot. 3. From the Control Panel's System and Security, click Find and fix problems. 3. To create a USB recovery drive: 1. Recovering your system Resetting your All-in-one PC The Reset your PC option restores your...
User's Manual for English Edition
Page 7
... use this option, click Get Started. 4. Follow the onscreen instructions to complete. 1. Click Next. 7. IMPORTANT! NOTE: This process may take a while to complete the reinstallation and reset process. Under this option. 5. Click Create. Click Settings > Change PC Settings > General. 3. When the process is completed, click Finish. Removing everything and reinstalling Windows Restoring your data before using the Remove everything and reinstall Windows option. Select the USB storage device...
... use this option, click Get Started. 4. Follow the onscreen instructions to complete. 1. Click Next. 7. IMPORTANT! NOTE: This process may take a while to complete the reinstallation and reset process. Under this option. 5. Click Create. Click Settings > Change PC Settings > General. 3. When the process is completed, click Finish. Removing everything and reinstalling Windows Restoring your data before using the Remove everything and reinstall Windows option. Select the USB storage device...