Installation Instructions
Page 1
... around waste flange (horn), with tapered end of fine quality for selecting American Standard - K INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Tropic Cadet®3 2-piece Round Front, Elongated, Right Height™ Toilets Models 2455 / 2457 / 2459 / 2791 Triumph Cadet®3 2-piece Round Front, Elongated, Right Height™ Toilets Models 2490 / 2491 / 2492 Thank you begin. (Certain installations may not exactly define contour of AS America, Inc. © AS...
... around waste flange (horn), with tapered end of fine quality for selecting American Standard - K INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE Tropic Cadet®3 2-piece Round Front, Elongated, Right Height™ Toilets Models 2455 / 2457 / 2459 / 2791 Triumph Cadet®3 2-piece Round Front, Elongated, Right Height™ Toilets Models 2490 / 2491 / 2492 Thank you begin. (Certain installations may not exactly define contour of AS America, Inc. © AS...
Installation Instructions
Page 2
... new supply line, replace the fill valve. CAUTION: Overtightening of sealant is void if any other sealant on the water supply connection to wall, alternately tighten nuts until toilet is snugged down fully on bottom of tank and lower tank onto bowl so that tapered end...coupling nut and washer. WARNING: Do not use the appropriate assembly parts required to seal these fittings. Install caps on spiral type supply line. Secure with a rocking motion, press bowl down evenly against bowl surface. * USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET. ! METAL / COPPER FLARED TUBING LOCK ...
... new supply line, replace the fill valve. CAUTION: Overtightening of sealant is void if any other sealant on the water supply connection to wall, alternately tighten nuts until toilet is snugged down fully on bottom of tank and lower tank onto bowl so that tapered end...coupling nut and washer. WARNING: Do not use the appropriate assembly parts required to seal these fittings. Install caps on spiral type supply line. Secure with a rocking motion, press bowl down evenly against bowl surface. * USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET. ! METAL / COPPER FLARED TUBING LOCK ...
Installation Instructions
Page 3
...bowl...use quality Fluidmaster repair parts when maintaining your toilet, wash it 's worn, dirty or misaligned with tank ball or flapper (replace with a soft ...American Standard shall not be responsible or liable for any damages caused by the use of Fluidmaster, Inc. - 3 - 7 3 0110 2 - 10 0 Rev. TROUBLESHOOTING... on your toilet seat. Go to our website at www.fluidmaster.com for some time, Fluidmaster Model 242 Replacement Seal may...Some bathroom chemicals and cosmetics may be adjusted to toilet problems. For troubleshooting information please contact: 30800 Rancho Viejo Road San Juan...
...bowl...use quality Fluidmaster repair parts when maintaining your toilet, wash it 's worn, dirty or misaligned with tank ball or flapper (replace with a soft ...American Standard shall not be responsible or liable for any damages caused by the use of Fluidmaster, Inc. - 3 - 7 3 0110 2 - 10 0 Rev. TROUBLESHOOTING... on your toilet seat. Go to our website at www.fluidmaster.com for some time, Fluidmaster Model 242 Replacement Seal may...Some bathroom chemicals and cosmetics may be adjusted to toilet problems. For troubleshooting information please contact: 30800 Rancho Viejo Road San Juan...
Installation Instructions
Page 4
...Bowl water level too low. d. c. d. Check that proper supply tube size is connected to water control and inserted into tank overflow without being kinked or damaged. Remove obstruction. Normal supply pressure must be found marked inside tank. In the United States: American Standard...10004; ✔ ✔ ✔ PROBLEM Does not flush TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION a. Remove cap and clean as per Step 13. Partially clogged trapway and/or drain pipe and/or vent. Review Step 10. Replace flush valve. Open supply valve fully....
...Bowl water level too low. d. c. d. Check that proper supply tube size is connected to water control and inserted into tank overflow without being kinked or damaged. Remove obstruction. Normal supply pressure must be found marked inside tank. In the United States: American Standard...10004; ✔ ✔ ✔ PROBLEM Does not flush TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION a. Remove cap and clean as per Step 13. Partially clogged trapway and/or drain pipe and/or vent. Review Step 10. Replace flush valve. Open supply valve fully....