Adaptec AHA-2930 - AHA Storage Controller Ultra SCSI 20 MBps Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec AHA-2930 manuals!
Problems with Adaptec AHA-2930?
Ask a Question
Free Adaptec AHA-2930 manuals!
Problems with Adaptec AHA-2930?
Ask a Question
Most Recent Adaptec AHA-2930 Questions
Low Profile Version Of Aha-2930cu
What is the difference with AHA-2930CU and AHA-2930LP. Is it just a form factor or there are other d...
What is the difference with AHA-2930CU and AHA-2930LP. Is it just a form factor or there are other d...
(Posted by oleglomakin 11 years ago)
Popular Adaptec AHA-2930 Manual Pages
Installation Guide - Page 1
Adaptec, the Adaptec logo, AHA, EZ-SCSI, and SCSISelect are registered trademarks, and Windows NT is subject to its accuracy, Adaptec, Inc. All other countries used are owned by any form or by their respective owners.
Installation Guide
AHA-2930B
Adaptec, Inc. 691 South Milpitas Blvd. Windows and Windows 95 are trademarks of this document to assure its users. Printed in the ...
Installation Guide - Page 2
...pin 8-bit high-density external SCSI connector PC/Mac auto detection jumper (ON for PC/ AUTOMATIC )
Helpful Hints
Configuring SCSI Devices 6 Configuring Disk Drives 6 Installing Multiple Adapters . . . . 6 Using Board Control (Macintosh) 7 Using SCSISelect (PC 8 Troubleshooting Checklist . . . . . 11 Common Problems and
Solutions 12
1 Introduction
The AHA®-2930B host adapter provides...
Installation Guide - Page 3
...contact your vendor). To set for Automatic
platform detection (jumper shunt is set the AHA-2930B board for Macintosh operation...
2-pin LED Cable
LED Connector on the SCSI bus. Step 3: Normally jumper J4 is removed... your computer documentation.)
The PCI slot must support bus master data transfers (refer to the
...the expansion slot bracket that covers the card-slot opening. Step 4: Insert the ...
Installation Guide - Page 4
... you are installing external SCSI devices only, replace the computer chassis cover and skip to Installing External SCSI Devices on page 4. Pin 1
Termination Enabled
Termination Disabled
Step 2: Install and mount each internal SCSI device
inside your computer. (Refer to your computer and device documentation for SCSI ID settings and instructions on manually changing the default settings.)
If you...
Installation Guide - Page 5
... described in Using SCSISelect (PC) on page 8, and set the Boot Target ID to correspond to the SCSI ID of the boot device.
2
3
Terminating Plug
Step 2: To connect additional external SCSI devices,
daisy-chain each device to the previous device until all devices are installing only one external device, enable the device termination or...
Installation Guide - Page 6
... AHA-2930B, you purchased your local hard disk drive. s The Adaptec® 7800 Family Manager Set provides software driver support for the Macintosh
Power Macintosh users with your host adapter and SCSI devices in computers running under DOS, Windows®, Windows 95®, and Windows NT™. Copy the Board Control software to the third-party documentation for installation instructions...
Installation Guide - Page 7
... SCSI device at bootup. Configuring SCSI Devices
Your host adapter can support the SCSI Configured AutoMatically (SCAM) protocol, which automatically assigns SCSI IDs dynamically and resolves SCSI ID conflicts at the end of all SCSI devices connected to the host adapter, make sure the Hard Disk (or Drives) setting in use it to the SCSI specification. However, if you install the AHA-2930B...
Installation Guide - Page 8
... host adapter lies between the ends of Board Control Settings
This section defines the AHA-2930B default settings. After you change the default setting of the host adapter. To determine if a device supports parity, read the device documentation. s Select a SCSI Bus-The SCSI Bus window displays the host adapters connected the SCSI bus. To give the host adapter the highest...
Installation Guide - Page 9
... the media, it is enabled, you to change host adapter settings without opening the computer case when using the AHA-2930B in SCSISelect take effect after the computer boots. To toggle the display between color and monochrome modes, press F5 (this operation.
Most SCSI disk devices are no longer used. Starting the SCSISelect Utility...
Installation Guide - Page 10
... setting is supported. s Host Adapter SCSI Termination-This option sets termination on the host adapter and all SCSI devices. To configure a specific device, you leave the host adapter at its default setting of Automatic.
This option sets the maximum synchronous data transfer rate that cables are connected to Automatic, Enabled, or Disabled.
s BIOS Multiple LUN Support...
Installation Guide - Page 11
... if you want to boot from on , install a removable-media device driver and set this option even if you may lose data! Several SCSISelect options are supported by the BIOS are treated as hard disk drives.
- When you partition a disk under BIOS control larger than 1 GByte, the AHA-2930B includes an extended translation scheme. Additional Options...
Installation Guide - Page 12
... BIOS Support for SCSISelect (TM) Utility! message appears on your computer's documentation for instructions. If this setting is an option to a specific PCI bus slot, so if you installed the host adapter in a bus master PCI slot?
This option determines whether the Press for Bootable CD-ROM - s Display Message During BIOS Initialization - Troubleshooting Checklist
If you install...
Installation Guide - Page 13
... to the drive is set of available IRQs for instructions on to use the Format/Verify utility on a disk device and got an Unexpected SCSI Command Failure pop-up all data
on the drive.
3 If this does not solve the problem, back up box with error information, the utility probably encountered a problem with the SCSISelect Format...
Installation Guide - Page 14
... the problem.
13 If it requested data from an installed SCSI device. Device connected, but fails to spin up .
03h - An unexpected time-out occurred. Check the SCSI bus termination. Unit attention-The removable media may be defective.
If the message still appears, follow the drive manufacturer's instructions to make sure the drive is set to...
Installation Guide - Page 15
... Canada.
This device complies with part 15 of 16 Print Spec Number: 495645-00 Current Date: 3/18/97 Last Modified: March 18, 1997 8:24 am File Location: D:\MARIO\2930B_b-ig\2930b.fm ECN Date: 3/24/97
radio communications. AHA-2930B Installation Guide Part Number: 511227-00, Rev....equipment off and on a circuit different from that interference will not occur in a particular installation.
Adaptec AHA-2930 Reviews
We have not received any reviews for Adaptec yet.