Adaptec 2060900 Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 2060900 manuals!
Problems with Adaptec 2060900?
Ask a Question
Free Adaptec 2060900 manuals!
Problems with Adaptec 2060900?
Ask a Question
Popular Adaptec 2060900 Manual Pages
User Guide - Page 14
... Ultra320 SCSI Cards User's Guide
Using Multiple Host Adapters With UnixWare/Open Unix/OpenServer 11-9 Removing the Driver 11-10 Troubleshooting 11-11 Problems and Solutions 11-11 Error Messages 11-12
12 Installing the SCSI Driver for Sun Solaris
Installing the Driver When Installing Solaris 9 12-2 Installing the Driver When Solaris 9 is Already Installed 12-3 Removing the Driver From Solaris 9 12...
User Guide - Page 77
... the array is Already Installed on page 5-2, or Installing the Driver When Windows 2000 or Windows Server 2003 is built, insert the Windows setup CD in the CD-ROM drive and restart the system to finish setting up Windows.
5-2 Select Adaptec HostRAID U320 Driver for more to begin driver installation, see either, Installing the Driver For a Fresh Installation of Windows
1 Create...
User Guide - Page 83
... displays the adapter drivers supported on the disk. Installing the Driver When Windows NT 4.0 is Already Installed
To update or install the a320raid.sys driver if Windows NT 4.0 is already installed: 1 Start Windows NT 4.0. 2 Click the Start button on -screen and in
your computer.
6-3 Follow the instructions on the Windows NT 4.0 task bar, and then
point to Settings. 3 Click the Control...
User Guide - Page 119
...'s Guide
Troubleshooting
Error Messages
The error messages listed below are listed sequentially according to allocate memory This indicates that there may have installed a new adapter and have not updated the driver on your system. [xxxxx084] Adapter software initialization failure An error has occurred while the driver was setting up -to -date version of the driver Your adapter is supported...
User Guide - Page 121
... with the amount of another board installed in your system. Adaptec Ultra320 SCSI Cards User's Guide
[xxxxx0ac] Driver already loaded for all the supported adapters in this system. [xxxxx0a4] SCSI bus reset by third-party hardware
Hardware such as an array enclosure may be a problem with the IRQ of memory installed in your system. See Using...
User Guide - Page 128
...-7 Installing the SCSI Driver for host adapter operation. If so, go back and correct any problems before proceeding. 3 Wait for UnixWare/Open Unix should appear on -screen instructions (...installed SCSI
devices are listed. If some or all your SCSI cables may be loose, or the SCSI device setup may not be ready to shut down. The updated driver for UnixWare/Open Unix to Troubleshooting...
User Guide - Page 133
... operation continues. [xxxxx010] Error issuing command
An error has occurred while the driver was setting up its internal data structures. Adaptec Ultra320 SCSI Cards User's Guide
Error Messages
The error messages listed below are listed sequentially according to the last three digits of the error code. For example, [xxxxx020], [xxxxx021], [xxxxx022], and so forth. Try installing the most upto...
User Guide - Page 136
... hardware initialization failure - This is not present. possible resource conflict The driver has attempted to your host adapter's user's guide for troubleshooting information. [xxxxx0d7] Target device scan failed The driver encountered an error scanning the target device. Installing the SCSI Driver for troubleshooting information.
11-15 Refer to initialize the adapter hardware but failed...
User Guide - Page 155
... User's Guide
Troubleshooting Checklist
Most problems with using the Adaptec SCSI Card results from one connector! s Have you have problems, check these items first: s Are all SCSI cables and power cables properly connected? A-2
s Are all three connectors, disconnect devices from errors in the PCI/PCI-X expansion slot? s Is the PCI expansion slot compliant with a specific SCSI...
User Guide - Page 156
... specification allows the motherboard manufacturer to the AGP slot. Most motherboard CMOS/BIOS setup utilities have verified that all IRQs not specifically required for troubleshooting in all the Windows operating systems. For troubleshooting specifically .... These are some basic steps that can 't load the driver and suspect that all devices not being assigned. You will need to Available ...
User Guide - Page 161
...], [xxxxx011], [xxxxx012], and so on. B-2
Driver Error Messages
The following error messages are described in Driver Error Messages:
Note: The entry in the third row of the last column identifies the SCSI ID of the error message. Try installing the most cases, the error is not supported by the driver.
Note: When reporting problems to Customer Support, be sure to include the...
User Guide - Page 177
... Click Close on the driver Properties window. 17 You will be prompted with this warning message: "The software you can use the RAID features.
E-3
Migrating From Adaptec Ultra320 SCSI to restart the computer. Enabling HostRAID Support
After installing the HostRAID driver, you must enable HostRAID support before you are about to install does not contain a Microsoft...
User Guide - Page 180
Enabling HostRAID Support
After installing the HostRAID driver, you must enable HostRAID support before you can detect the new enabled driver hardware. Windows XP will detect the newly enabled HostRAID support and will prompt you for this warning message: "The software you need to restart the computer. E-6 Adaptec Ultra320 SCSI Cards User's Guide
13 You may be prompted...
User Guide - Page 182
... receive the following Service Control Manager error: At least one service or driver failed during subsequent restarts, Click on Start=>Settings=>Control Panel and double-click the SCSI Adapters icon. 2 Click the Drivers tab, select the appropriate SCSI card driver (it will be labeled Not Started) and click Remove. Enabling HostRAID Support
After installing the HostRAID driver, you must enable...
User Guide - Page 192
...Before you disable HostRAID, for instructions. F-9 Migrating from HostRAID to Adaptec Ultra320 SCSI
Disabling HostRAID Support
After installing the HostRAID driver, you must disable HostRAID support before you must break a...to delete any channel containing an array, scroll down and select Configure/View HostRAID Settings. 4 Select the array by scrolling to delete the selected array. See the ...
Adaptec 2060900 Reviews
We have not received any reviews for Adaptec yet.