Yamaha RX-V596 Support Question
Yamaha RX-V596 Support Question
Find answers below for this question about Yamaha RX-V596.Need a Yamaha RX-V596 manual? We have 1 online manual for this item!
Question posted by ningalls8962 on November 15th, 2020
The Remote Power Button
When I hit the remote power button for the tuner nothing happens. Volume works fine.
Current Answers
Answer #1: Posted by hzplj9 on November 15th, 2020 10:20 AM
hzplj9
Member since:
June 25th, 2012 Points: 4,874,710
Member since:
June 25th, 2012 Points: 4,874,710
If the unit can be switched on and off at the device then I would suspect the remote control has an issue. If they are used for a prolonged period, in time the most used button will start to fail. This can be solved by taking apart and cleaning if that is possible or purchasing a replacement remote. Have you checked the batteries? Simple mistake sometimes as a low battery voltage could alter the strength of the signal.
Hope that helps.
Related Yamaha RX-V596 Manual Pages
Owner's Manual - Page 4
... controls or connection cables. Do not connect audio component to the wall outlet, even if this unit...the power cord and then the cables connected to clean the unit with other component. ...; Do not attempt to other component such as tuners, receivers and TVs. MODEL:
Serial...Always set VOLUME to provide. Grounding or polarization - This unit is not disconnected from such component if ...
Owner's Manual - Page 5
...Power... FM/AM Tuner x 40-...Audio/Video System x Test Tone Generator for Easier Speaker Balance Adjustment x 6-Channel External Decoder Input for your operation.
• When buttons on this unit and the remote control are noted together in this Owner's Manual, these button names are trademarks of "button name (remote control button name)".
1
APPENDIX
English Confidential Unpublished Works...
Owner's Manual - Page 8
...OFF position, press EFFECT to turn on the power of this unit or to set VOLUME to the "m" position. You can listen to the sound to be output from the remote control. 3 Display This shows various information. ... to or watch. Set the button(s) to the OFF position for the DVD/LD, TV/digital TV and cable TV/satellite tuner sources. 5 INPUT SELECTOR Turn this button to select the input mode among...
Owner's Manual - Page 11
...
Remote Control
This section describes the basic operation of this dial to select the position for the component to be controlled. (The proper code must be controlled.
3 Numeric buttons (Input selector buttons)
These buttons select the input source.
Refer to "Setup codes" on page 42 for full details.
1
8
2
9
0
Select the AMP/TUN position.
3
4 5 6
TV POWER TV VOLUME...
Owner's Manual - Page 14
... 12)
Decoder (page 15)
Connecting the Speakers (pages 16 and 17)
Connecting the Power Supply Cords (page 18)
(U.S.A. Use RCA-type pin plug cables for each component to be distinguished as !, #, $ etc. model)
A
B
Connecting an Audio Component (page 13)
Connecting a Video Component (pages 14 and 15)
IMPEDANCE SELECTOR switch (page 18)
10
The input and...
Owner's Manual - Page 17
... turntable to connect the right channel (R), left channel (L), input (IN) and output (OUT) properly.
BASIC OPERATION ADVANCED OPERATION
APPENDIX
English
13 INTRODUCTION
PREPARATION
Connecting an Audio Component
Turntable
OUTPUT
LR
GND
(U.S.A.
Owner's Manual - Page 18
... them from dust.
• If your DVD/LD player, TV/digital TV or cable TV/satellite tuner, etc. To make a connection between the digital signal terminals, you should connect the components to the samenamed analog audio signal terminals of priority with the input mode set to connect the right channel (R), left channel (L), input...
Owner's Manual - Page 25
...you use two main speaker systems, press both A and B. Front panel or
Remote control
7
2
4
6
1 Set VOLUME to the "m"
position.
2 Turn the power on
the display. DECODER".
• If you select and play back result... audio source connected to be played.
To select a tape or an MD source
Press TAPE/MD MON / EXT. y
For the DVD/LD, TV/digital TV and cable TV/satellite tuner ...
Owner's Manual - Page 26
...the component you select the audio source with the input selector buttons on the remote control.
Refer to "PRESET REMOTE CONTROL"...Remote control
22
Front panel
or Remote control
s To mute the sound
Press MUTE on the display. s When you have finished using this unit in the standby mode. The BGV function does not work...an audio source with INPUT SELECTOR on page 42.
6 Adjust the volume ...
Owner's Manual - Page 27
...power of this unit, the input mode for the DVD/LD source is always set to AUTO and for TV/ digital TV or cable TV/satellite tuner...TUNER, TAPE/ MD, VCR, PHONO and VIDEO AUX sources because only analog signals are being input at the same time.
or
Front panel
Remote... the input mode
Press INPUT MODE (or the input selector button that send both the OPTICAL and COAXIAL terminals, the digital ...
Owner's Manual - Page 39
... item appears on the display.
If, however, the power cord is disconnected from being lost when this unit is cut for audio listening and video watching.
1. REAR SP 3. BASIC ... return to the preset positions and values. INTRODUCTION
PREPARATION
SET MENU
This unit provides you with the remote control while watching the information on the display.
1
3
2
1 Set the selector dial to ...
Owner's Manual - Page 45
...panel of this unit in the standby mode by using STANDBY on the remote control (or STANDBY/ON on the front panel), or by disconnecting the AC power cord from the AC power outlet.
3
1 Play a source you want to enjoy when you ...3 Press SLEEP repeatedly to
select the desired SLEEP time.
This timer is effective for the components connected to the previous indication. Lights up on the display.
Owner's Manual - Page 46
...YAMAHA audio components connected to it. CBL/SAT A cable TV or satellite tuner can be controlled. Refer to the following buttons. CD...DSP programs can be selected directly.
TV POWER @ TV INPUT # TV VOLUME
42 Selector Dial
There are nine positions that...REMOTE CONTROL
The provided remote control is factory set to control not only this unit and your TV with this button is used buttons...
Owner's Manual - Page 47
... dial to the
CD position.
3 Turn on page 48 for the CD player operation buttons.
7 Adjust the volume. PRESET REMOTE CONTROL
43
English
APPENDIX
BASIC OPERATION ADVANCED OPERATION
PREPARATION
INTRODUCTION Refer to "Setup codes" on the power.
4 Press INPUT.
Controlling the Components Connected to This Unit
s Example: To control a YAMAHA CD player
2 6
4
5
3
7
1 Make sure that...
Owner's Manual - Page 48
... deck A or B on a tape deck or MD recorder. s STOP This button stops operation on the tape deck that has a remote control with a power button if you have set the code for another manufacturer.
• The dark-shaded buttons do not function. • If your component.
44 AV POWER (TAPE) This button turns on a tape deck or MD recorder.
Owner's Manual - Page 49
... codes listed for the manufacturer, use the original remote control
supplied with a power button if you want to the next or previous CD. The button functions as PAUSE/STOP* for about three seconds after pressing DSP, this button turns on the track that has a remote control with your component does not respond to the beginning of the...
Owner's Manual - Page 50
... you have set the code for the manufacturer, use the original remote control
supplied with your component.
46
DISC SKIP+/- Also this button turns on the DVD player that has a remote control with a power button if you have set the code number "0048".
Also this button turns on the YAMAHA DVD player if you have set the...
Owner's Manual - Page 51
... SLEEP TV MUTE
• The dark-shaded buttons do not function. • If your component.
47
APPENDIX
English PLAY
REWIND
Numeric buttons
ENTER/RECALL
+10 CHANNEL +/-
Select the TV position. VCR PLAY VCR REWIND
TV POWER This button turns on a cable TV/satellite tuner that has a remote control with a power button if you have set the code for your...
Owner's Manual - Page 52
... re-enter the code.
5 Press AV POWER (or any other button) on your component to be used . 2 Set the selector... dial to check if you have set the code correctly.
Notes
• You can control a second (and third) VCR in the CBL/SAT and DVD MENU positions if a cable TV or satellite tuner, or DVD player is not being used . PRESET REMOTE...
Owner's Manual - Page 60
...Antennas 11, 12 Audio components (tape deck/MD recorder, CD player and turntable 13 Digital connections 14 Speakers 16 TV monitor 14 Video components (DVD/LD player, VCR, TV/digital TV and cable TV/satellite tuner 14
D
Delay time... preset tuning 28 Manual preset tuning 29
R
Recording 31 Remote control
Basic operations 7, 8 Batteries 2 Factory-set code 49 Manufacturer's codes ..........
Similar Questions
Unit Powers On But No Input Works
Powered up unit but will not process signal from multiple inputs e.g. XBox cable input. TV works ok ...
Powered up unit but will not process signal from multiple inputs e.g. XBox cable input. TV works ok ...
(Posted by kevindawydiuk 2 years ago)
Unit Was Working Fine With Tv And Abruptly Powered Off.
can not get the unit to power back on. Could this be a fuse?
can not get the unit to power back on. Could this be a fuse?
(Posted by billbozone 8 years ago)
Remote Control Will Not Change Volume
Periodically the remote control will not operate the volume dial motor. Sometimes I can manually rot...
Periodically the remote control will not operate the volume dial motor. Sometimes I can manually rot...
(Posted by BillZancho 9 years ago)
Yamaha Rx-v596 Fm Antenna Adapter
How do I hook up a fm antenna with 75-ohm cable?
How do I hook up a fm antenna with 75-ohm cable?
(Posted by dpeten 11 years ago)
