Yamaha EMX5 Support Question
Yamaha EMX5 Support Question
Find answers below for this question about Yamaha EMX5.Need a Yamaha EMX5 manual? We have 2 online manuals for this item!
Question posted by maesisonta on February 12th, 2023
Amplifier Protection Indicators.
Why did the amplifier protection indicator light on channel B flashing?
Current Answers
Answer #1: Posted by Odin on February 13th, 2023 10:34 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,640
Member since:
April 10th, 2010 Points: 41,236,640
See https://www.manualslib.com/manual/1178940/Yamaha-Emx5.html?page=13#manual [third listed problem].
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Yamaha EMX5 Manual Pages
EMX5 Technical Specifications - Page 1
...+48 V
Effect mute on/off
Load Protection: DC-fault Amplifier Protection: Over heat protection, Over current protection, Integral power protection Power Supply Protection: Over heat protection, Over current protection
AC 100-240 V, 50 Hz/60 Hz...level controls are at their maximum position.) *2 Level controls setting : Channel level controls are at their t position.
To obtain the latest ...
EMX5 Technical Specifications - Page 2
.../FX
3-Stage EQ
LEVEL
FX ON
AUX1
FX RTN LEVEL
Digital Audio Section
FEEDBACK MASTER BASS SUPPRESSOR EQ BOOST
STEREO LEVEL
PEAK +10 +6
0 -6 -10 -20
FEEDBACK SUPPRESSOR MASTER EQ, BASS BOOST
AD AD AD
AMPLIFIER MODE
STEREO L+R/AUX1
LIMIT CHA CHB
PROTECTION CHA CHB
LIMITER
POWER AMP DA
DA POWER AMP
STANDBY
MONITOR...
EMX5 Owners Manual - Page 3
... walk on, trip over, or roll anything over it might spill into contact with your audio system, always turn off the power switch and disconnect the plug from becoming too high. ...over and cause injuries.
• Do not block the vents. Do not install it with a protective grounding connection. EMX5 Owner's Manual 3 If you are emitted. - If it any containers (such as vases, ...
EMX5 Owners Manual - Page 4
... on or off , for devices such as microphones, and microphone amplifier circuits with high sensitivity in voltage. Otherwise, the device, TV... for damage caused by "NOTE" provides useful tips.
4 EMX5 Owner's Manual Doing so may result in order to prevent the... Environments: E1, E2, E3 and E4
• Information indicated by improper use speaker cables with a insulated-housing connector.
...
EMX5 Owners Manual - Page 5
... congratulations on your mixer.)
• AC power cord (2.5 m) • Technical Specifications (English only): Includes general specifications, input/output characteristics, and a block dia-
Please read this document)
EMX5 Owner's Manual 5 It also has a built-in overload protection function to match the usage. (See section @3 on page 11.)
High Efficiency Class-D Amplifier
This model has...
EMX5 Owners Manual - Page 6
... (a speaker without an internal amplifier) to use . Connect the included power cord.
Passive speakers
3. Connection order: Mixer [AC IN] jack ...EMX5 Owner's Manual
1. Sending the signal from both [SPEAKERS A/B] jacks to a single speaker may lead to the " t " position.
5. Quick Start Guide
Getting Sound to the left.) Precautions for connection of an instrument or audio...
EMX5 Owners Manual - Page 7
...LEVEL] controls for the channel that is reached. Power amplifier
Portable audio player
Passive speakers
NOTE
Normally, speakers are connected via a power amplifier that has the connected
...generated by the speakers. EMX5 Owner's Manual 7 Switching order: Instrument or audio device Mixer [
] (Power) switch
WARNING
When turning off the instrument or audio device.
8. However,...
EMX5 Owners Manual - Page 8
Adjust the [COMP] controls until you get the desired sound for channels you
wish to feedback. Avoid setting the value too high, as guitars, bass guitars, and drums.
8 EMX5 Owner's Manual Output
0 (Min)
10 (Max)
Input
Common Compressor Applications In addition to vocals, the compressor can be used to increase the level of...
EMX5 Owners Manual - Page 9
....
1. Turn on page 17.
2. EMX5 Owner's Manual 9
w The selected effect program number flashes in the display. The switch lights up to indicate that can also select and confirm the ...Use the FX RTN [LEVEL] control to adjust the effect depth for an extended period of each channel you conveniently bypass/enable the built-in effects.
3.
Connect a control device such as reverb time...
EMX5 Owners Manual - Page 10
... on ( ) when you to the mixer without the need for each function.
!7 [PROGRAM] rotary encoder For selecting one of 12 dB/octave. This function affects only the phone jack input.
10 EMX5 Owner's Manual
i [MIC/LINE] input jacks (Channels 1 - 4) For connecting microphones, guitars, electronic musical instruments or audio devices. NOTE
The FX RTN [LEVEL...
EMX5 Owners Manual - Page 11
... bus or L+R/AUX1 bus.
@9 AMPLIFIER [PROTECTION] indicators Lights up when the DSP amplifier protection limiter is on.
@4 [AUX1 SEND] jack [AUX2 SEND] jack For connecting to a musician monitoring system, external effect device, and so on ( ) to supply all inputs for channels 1 to indicate that the indicators flash continuously, the internal power amplifier section will cut the unnecessary...
EMX5 Owners Manual - Page 12
...EMX5 Owner's Manual It is not used during use. First, connect the included power cord to be used only for performing maintenance.
Also, the signal to the mixer... noise or electromagnetic interference.
#6 [USB] terminal This is determined according to connect the speakers. AMPLIFIER [MODE] switch setting "STEREO" "L+R/AUX1"
[SPEAKERS A] Jack
STEREO L signal L+R signal
[SPEAKERS...
EMX5 Owners Manual - Page 13
... off.
The AMPLIFIER [PROTECTION] indicators are flashing or constantly on ? Turning the [MASTER EQ] control to the left of the mixer are not clear.
How can the monitor output be output from the [SPEAKERS A] jack. Please wait until the amplifier has cooled down to the [AUX1 SEND], [AUX2 SEND] jacks. EMX5 Owner's Manual 13...
EMX5 Owners Manual - Page 14
... locks in place.
• Use speaker cables with an insulated-housing connector.
2-channel Connection
When connecting using the following configuration, use speakers with impedance from 4 ohms to 8 ohms.
4Ω to 8Ω
4Ω to 16Ω
14 EMX5 Owner's Manual Appendix
Connecting Speakers
When you wish to connect multiple speakers from 8 ohms...
EMX5 Owners Manual - Page 15
... that these vents are well clear of walls or other objects.
Exhaust
At least 30 cm
At least 30 cm
At least 30 cm
Intake
EMX5 Owner's Manual 15 Appendix
Installation
This mixer has vents located on the floor. CAUTION
Do not push too forcefully when tilting the...
EMX5 Owners Manual - Page 16
...protection.
2. Use six of rack-mount space.
* 7U is heavy, and should be cases in a rack are marked as "L" (Left) or "R" (Right).
16 EMX5 Owner's Manual
This mixer requires 7U* of the screws you install this mixer along with the mixer...Refer to ensure that the screws do not damage surfaces such as power amplifiers that are not used in Step 1. NOTICE
Be sure to use the RK-...
EMX5 Owners Manual - Page 17
... the sound, producing an effect similar to the sound. A wah-wah effect with different delay times. Recreates the lo-fi sound of an AM radio. EMX5 Owner's Manual 17
EMX5 Owners Manual - Page 20
Appendix
General Specifications
Maximum Output Power (1 kHz) Input Channels Output Channels Bus
Input Channel Function
COMP Equalizer
Level Meter Phantom Power Voltage Built-in Effect FOOT SW DSP Processing
SPX Algorithm
Protection
Power Requirements Power Consumption Dimensions when placed vertically (W × H × D) Net Weight Optional Accessory Operating Temperature
THD+N
EMX5 Owners Manual - Page 21
...[AC IN] jack 12 AMPLIFIER [LIMIT] indicators 11 AMPLIFIER [MODE] switch 11, 12 AMPLIFIER [PROTECTION] indicators 11 AUX1 MASTER [LEVEL] ...control 11 [MIC] input jacks 10 [MIC/LINE] input jacks 10 [ MIC/ LINE] switches 7, 10 Mixer accessory
Rack-mount brackets 5, 16 [MONITOR EQ] switches 11
P
Parallel connection 14 [PARAMETER] control 10 [...
V
Vents 11, 15
X
XLR 18
EMX5 Owner's Manual 21
EMX5 Owners Manual - Page 22
..., you wish to discard these requirements provides a reasonable level of disposal.
(weee_eu_en_01)
22 EMX5 Owner's Manual IMPORTANT: When connecting this type of the following measures:
Relocate either this product... USA.
3. If you will not result in harmful interference with this manual as indicated in the instructions contained in this product in the space provided below and retain this...
Similar Questions
Regarding Training Videos For Mpg24/32 Audio Mixers
Where can I obtain training videos for Yamaha 24/32 audio mixers?
Where can I obtain training videos for Yamaha 24/32 audio mixers?
(Posted by jimmycjr87 7 years ago)
Pfl Flickers By Output Signal Indicators
Why does the pfl led flash when it appears there are no signal sources in the mix. This is new unit.
Why does the pfl led flash when it appears there are no signal sources in the mix. This is new unit.
(Posted by rcholmes60 9 years ago)
Emx Protection Circuit Problem
EMX 5000 Yamaha 12: With a mic plugged in and connected to speakers. The sound comes out for about a...
EMX 5000 Yamaha 12: With a mic plugged in and connected to speakers. The sound comes out for about a...
(Posted by johnfputnam 11 years ago)
Repair Manual For Dm2000 Digital Mixer ?
Is a repair manual for DM2000 digital mixer available ?
Is a repair manual for DM2000 digital mixer available ?
(Posted by dean5533 11 years ago)
Yamaha Mixer Oiv96 Initial Set Up
After removing the CMOS battery while servicing the mixer, it cant start, it indicates its calibrati...
After removing the CMOS battery while servicing the mixer, it cant start, it indicates its calibrati...
(Posted by kasaija2003 11 years ago)