Yamaha EMX5000-12 Support Question
Yamaha EMX5000-12 Support Question
Find answers below for this question about Yamaha EMX5000-12.Need a Yamaha EMX5000-12 manual? We have 1 online manual for this item!
Question posted by johnfputnam on April 20th, 2013
Emx Protection Circuit Problem
EMX 5000 Yamaha 12: With a mic plugged in and connected to speakers. The sound comes out for about a half second, a click sound is heard in the amp and then no sound. After about 2 seconds, this process can be repeated again. It cuts out and clicks and then no sound. I have tried different receptacles and locations, different mics and different power cords for the amp. The click sound is something like a breaker being thrown off inside the amp.
Current Answers
Related Yamaha EMX5000-12 Manual Pages
Owner's Manual - Page 2
... EMX5000-20, EMX5000-12 owner's manual have been revised.
B- Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer.
Jacks 1 are Speakon-type connectors. The LIMITER indicator will deliver 100W into 4Ω.
1 EMX5000-20/EMX5000-12 Parts of the original owner's manual. The Owner's Manual Revisions
E
Thank you for connecting Speakon...
Owner's Manual - Page 3
...EMX5000-20/EMX5000-12
CH INPUT
A
[-60~-16dB]
[-34~+10dB]
EMX5000-12:CH1-8 EMX5000-20:CH1-16 B
CH INSERT I/O [0dB]
EMX5000-12:CH1-8 EMX5000-20:CH1-16
+48V
PHANTOM 8CH/SW
EMX5000-12:[CH1-8] EMX5000... OUT [+4dB]
A
POWER AMP IN [+4dB]
B
YAMAHA SPEAKER PROCESSING
YSP
YSP
MAIN L AUX1 AUX1
MONO BRIDGE
INV
Signal Select
MAIN R MONO
AUX2 MONO BRIDGE
POWER AMP Controls
LIMITTER
500W
300W 100W...
Owner's Manual - Page 4
...Yamaha may be connected to those products distributed by Yamaha...plug which is coloured BROWN must be of sufficient magnitude to constitute a risk of this apparatus may cause interference harmful to eliminate the problem by the interference. The wire which is intended to alert the user to this manual, meets FCC requirements. When connecting...branch (circuit breaker or fuse) circuits or ...
Owner's Manual - Page 5
...
• Turn off , remove the power plug from the AC outlet, and remove all musical instruments, audio equipment, and speakers when connecting to this Owner's Manual or as when going on a power cord covered by a carpet. • Use only the included power cord for repair. A sudden blast of sound may be damaged, turn the power...
Owner's Manual - Page 6
...electronic devices
• The digital circuits of the connected unit and speakers, and may induce
noise. ...speakers.
Influence on cell phone usage • Using a cell phone (mobile telephone) near this unit may induce a slight noise into nearby radios and TVs.
Doing so may cause oscillation depending on the operating environment and is unavoidable.
EMX5000-20/EMX5000-12...
Owner's Manual - Page 7
... of the internal power amp as appropriate for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer.
Introduction 5
Introduction
Thank you for the size of the room or the input capacity of the speakers.
• Two multi-effect units are provided. You can be selected as 16 (EMX5000-20), 8 (EMX5000-12) monaural input channels compatible with bridge connection), and is built...
Owner's Manual - Page 8
... be sure to turn the plug to the right to lock the connection after inserting the plug. Never connect the speakers in the SPEAKERS jack section on the panel) to learn more about using a Speakon cable. For other connections and power amp select switch settings. In this Quick Guide section to ST L-R.
EMX5000-20 (EMX5000-12)
Setting the power amplifi...
Owner's Manual - Page 9
... 1-8 (EMX5000-12), using the INPUT A jacks if the mic has an XLR plug, or the INPUT B jacks if the mic has a phone plug.
Refer to the operation manual of the corresponding device for the same channel at once (EMX5000-20: 1-8 and 9- 16, EMX5000-12: 1-8), so mics other than condenser mics must be connected to the INPUT A jack of the device.
EMX5000-20/EMX5000-12-Owner...
Owner's Manual - Page 10
... from the microphone. EMX5000-20 (EMX5000-12)
EMX5000-20 (EMX5000-12)
Synthesizer, Drum machine, Guitar processor
STEP 2 Power on
1 Turn on . EMX5000-20/EMX5000-12-Owner's Manual Otherwise, press the 26dB PAD switch on the YAMAHA SPEAKER PROCESSING switch in stereo.
8 EMX5000-20/EMX5000-12 Quick Guide
Connecting an electronic musical instrument To the EMX5000-20/EMX5000-12's LINE or ST...
Owner's Manual - Page 11
... the volume of the speakers.
3 Set the EFFECT RTN fader to the "0" position. 3
EMX5000-20 (EMX5000-12)
EMX5000-20 (EMX5000-12)
STEP 4 Applying built-in the EFFECT section. EMX5000-20 (EMX5000-12)
4
STEP 5 Power off
1 Press the POWER switch of the EMX5000-20/ EMX5000-12 to turn off the power to the unit.
2 Turn off the power to all connected devices.
• Be sure...
Owner's Manual - Page 12
... are as follows:
HIGH: 10kHz, ±15 dB,
shelving type
MID: 250Hz-5kHz, ±15 dB, peaking type
LOW: 100Hz, ±15 dB,
shelving type
EMX5000-20/EMX5000-12-Owner's Manual The base frequency (or center frequency), range of boost or cut it .
Owner's Manual - Page 13
...The indicator will be sent to external monitor amps or powered speakers.
6 EFF 1, 2 controls (EFFECT) For each channel, these control the amount of external equipment connected to the ST SUB IN 1, 2 jacks ...dB before the channel fader C) or post-fader (after the channel fader C). EMX5000-20/EMX5000-12-Owner's Manual A SIGNAL indicator This indicator will not affect the signals that clipping ...
Owner's Manual - Page 14
...speakers. If the Power amp select switch Y is set to MONO BRIDGE, this section, you to adjust the level of the outputs.
L AFL (after fader listen) switch When this fader does not affect the signal output from the 2TR IN jacks to the AUX SEND 1 jack (input/output panel 8).
EMX5000-20/EMX5000-12... is on, the output signal that is connected to the 2TR IN jacks (input/output ...
Owner's Manual - Page 19
... b) to this jack. Connect an external mixer output here. D PHONES jack This is a stereo phone type output jack, and is used to the STEREO bus. EMX5000-20/EMX5000-12-Owner's Manual The nominal ... mixer or external effect processor. The nominal output level is +4 dB.
E FOOT SW EFFECT 2 ON/OFF jack A separately sold Yamaha FC5 foot switch can connect either phone plugs or RCA phono plugs,...
Owner's Manual - Page 20
Connect the plug end of the cable to an AC outlet of the voltage printed below the inlet.
2 POWER switch This switch turns on or off the power to the EMX5000-20/EMX5000-12. The setting of the control panel power amp select switch Y will be lowered to the minimum position.
3 SPEAKERS (speaker output) jacks These jacks are used...
Owner's Manual - Page 21
... 1-MONO or AUX 1-AUX 2: Select either jacks 1 or 2, depending on the type of speaker cable you are connecting only one speaker to each to these jacks. When the power amp select switch is in which speakers can be connected to speaker jacks.
EMX5000-20/EMX5000-12-Owner's Manual
When placing the unit, make sure that the cooling ports are using...
Owner's Manual - Page 23
... add a subwoofer Additional/alternative PA system
EMX5000-20/EMX5000-12-Owner's Manual If more speaker outputs are needed, use the ST SUB OUT jacks and the MONO OUT jack. Connecting input/output equipment 21
Connecting input/output equipment
Microphone
Cassette deck CD player
Foot switch (YAMAHA FC5) (EFFECT ON/OFF)
Foot switch (YAMAHA FC5)
(TAP)
Synthesizer
Drum machine...
Owner's Manual - Page 31
... output from the speakers. When the device cools off , normal operation
the protection circuit for the exces-
The load on this device is greater than the nominal
level, lower the input to the nominal level. Possible reasons for following three points to prevent the problem from the EFFECT SEND jack to the connected effect processor...
Owner's Manual - Page 32
... Graphic equalizer Internal digital effect 1 Internal digital effect 2 Foot switch (FC5) Protection circuit (Power amp) Fan circuit Phantom power Option Power requirement/ Power consumption
SPEAKERS: 500 W+500 W/4Ω @0.5% THD at 1 kHz
325 W+325 W/8Ω...;C)
+48 V (balanced input)
FC5 (Foot switch), RK-124 (EMX5000-12)
USA and Canada:120 V AC 60 Hz, 400 W
Europe:
230 V AC 50 Hz, 550 ...
Owner's Manual - Page 33
... × 158 × 538 mm (EMX5000-12) 19 kg (EMX5000-20) / 15 kg (EMX5000-12) Power cord, Owner's Manual
s Input specifications
Input terminals
Gain control
Actual load impedance
For use with nominal
Sensitivity1
Input level Nominal
Connectors on mixer
Nominal
Max. Inrush Current: 70A Conformed Environment: E1, E2, E3 and E4
EMX5000-20/EMX5000-12-Owner's Manual
Similar Questions
Regarding Training Videos For Mpg24/32 Audio Mixers
Where can I obtain training videos for Yamaha 24/32 audio mixers?
Where can I obtain training videos for Yamaha 24/32 audio mixers?
(Posted by jimmycjr87 7 years ago)
Hi My Dm2000 Small Speaker Output Source Seems Faulty.
Hi my DM2000 Small speaker output source is not having audio output what can i do to get it fixed.my...
Hi my DM2000 Small speaker output source is not having audio output what can i do to get it fixed.my...
(Posted by fshindimba 9 years ago)
Yamalla Emx 3500 Power Mixer
play like new how much can sell for
play like new how much can sell for
(Posted by garciafloormat 10 years ago)
Does Emx 5000 Have A Fuse
where is the fuse located in emx 50000 / loss of power
where is the fuse located in emx 50000 / loss of power
(Posted by japerez1 11 years ago)