Uniden G455 Support Question
Uniden G455 Support Question
Find answers below for this question about Uniden G455.Need a Uniden G455 manual? We have 1 online manual for this item!
Question posted by mschramm3 on January 31st, 2013
Windows 7 Shows No Signal When I Plug In The Receiver
on my windows xp I get my security service udw115 to work on my windows 7 when I connect the receiver I get a no signal. I went through the trials in the manuel and have tryed to find the firewall to unblock that couldn't find anyway to do it
Current Answers
Related Uniden G455 Manual Pages
User Guide - Page 3
... Enter the UID Code 39 Enter Security Code 39 Record Video 40 Take A Snapshot 40 Downloading Apps 40 AndroidTM 40 iPhone®...42
Maintaining Your System 45 Upgrading your local, state and federal law.
© 2012. Uniden expects consumer's use of Your Hardware 45 Receiver 45 Cameras 45
Additional Information 48 Product Specifications...
User Guide - Page 5
If any items are missing or damaged, contact our Customer Care Line immediately. What's Included
You should have the following items:
G4 or G7 Receiver and Cradle
GC45 Camera (2) Stand (2)
AC Adapter (3)
Antenna (2)
Not Shown: Mounting screws, Ethernet cable, 2 extension cords, and SD Card. Never use damaged products!
5
User Guide - Page 6
... on. Getting to Know the Receiver and Cameras
Receiver (back/side)
Antenna
Cradle
Reset Power On/O
SD slot
Receiver Power Dock
Data Cable Connection
AC Power Connection
AC Power Connection
Pull-Out Stand
Front view
Power status
Back view
Antenna connector
Link status
Light sensor Microphone
Power pigtail
Power/Pair button
What the lights mean
...
User Guide - Page 7
... recommended that will reflect the light from the infrared LEDs used outdoors, they will still work; The camera is in pairing mode. Connect the other end of the receiver. Although the cameras can be mounted under some type of the receiver for a few seconds and then transitions to a 120 volt AC (standard indoor) power outlet. 3. As...
User Guide - Page 8
... you are positioning the camera, you have the display handy. 1. it's much easier to bring the receiver along; Before attaching the camera, tug gently on the stand to windows allows better transmission. &#... the base of -sight between the camera and monitor is securely in the wind - Placement next to make sure it and mark the location of the camera, including street lights, ceiling or floor...
User Guide - Page 9
...try reconnecting the AC adapter, and make sure the power outlet isn't controlled by turning the wingnut to secure it to the desired direction.
4 Adjust the post to the correct angle, then tighten the wingnut to
camera as needed. Set the mounting post to secure...to the camera's power pigtail and plug the other end into place. 5.
mounting screw. Connect one end of the camera. You ...
User Guide - Page 11
...difference between cameras, show all cameras on the screen itself let you extend the antenna. It also lets you view the camera transmissions.
Uniden Guardian Software Operation Overview
Your receiver's Uniden...always defaults to display images from the paired cameras. Live Screen
SD card status
Battery status
Record status
Camera number/ Signal strength
Pop up menus
Pop up menus, you...
User Guide - Page 12
...stop recording for that camera • Steady ...shows battery at nearly full.
What the icons Mean
Icon
Camera Mode
Volume
What it does Select how you want the Live screen to display camera input: • Scan between cameras (5 seconds) • Quad view (all paired cameras display) • Full view (1 camera displays on - Camera Number Record Status
Displays the camera number and signal...
User Guide - Page 16
... cord (see "Pairing" on page 20), tap the camera image you want to the first camera it to the selected channel, the receiver overwrites that is, you have "introduce" the camera and receiver so they can 't control which camera the receiver will detect first. The system automatically adjusts the Camera On screen accordingly. 4. If you can communicate). From...
User Guide - Page 17
...; pressing and releasing the pairing button quickly.
the camera's signal status icon shows no bars
• making sure the camera is plugged in and the red LED is on.
• making sure that the camera's antenna is attached and the receiver's antenna is extended.
• making sure the camera is plugged in and the red LED is on
two...
User Guide - Page 18
... they appear on by default. Makes the cameras visible to the receiver.
Motion detection is on the screens:
This screen should display:
The Uniden Guardian Settings screen highlights the Camera Setup option as the default. Main Screen Camera Setup
Recorder Setup
Sub Screens Pairing Camera on Brightness Motion Detection
Schedule Record
What it...
User Guide - Page 19
... until the screen is idle for 2 minutes to be used. (DHCP is most common.) Set a security code for remote access. Upgrades the receiver firmware. Formats/erases all the data on the SD card. Provides a list of internet connection to conserve power. Temporarily turns off the LCD after the system is unlocked. • Clock...
User Guide - Page 20
...:
the following icons as they can 't control which camera the receiver will automatically adjust the Camera On screen. Some things to know about pairing cameras:
•• If a camera is already assigned to the first camera it to a different channel.
20 Use this procedure to move a camera from one camera at the factory to pair.
Press and release...
User Guide - Page 21
... turned off , tap the camera icon. An X indicates a camera that camera.
21 A check mark replaces the X under the camera. 3. The receiver will automatically turn it is turned off , it on. To turn a camera off .
From the pop-up the camera with the receiver and the system will not receive video signals from that is still powered. Camera On
When you want...
User Guide - Page 27
... a melody for the alarm.
27 Tap the Network Information icon to the previous screen. The information in the DHCP setting is required (along with the security code) to gain remote access to your monitor from your cameras over the internet. Tap the arrow to return to display the Network Information screen.
2.
User Guide - Page 36
... User ID (UID) code and security code. Multiple users can access live video at the same time as long as provides an internet connection.
The number of remote viewers is determined by the amount of bandwidth on your system. System Requirements •• Microsoft® Windows XP, Vista, or Windows 7 •• Internet Explorer®...
User Guide - Page 41
... app; Tap Start to horizontal view.
41 Select Save. 8.
Enter the same security code that you wish to your system in the Device UID field.
6. Select a camera.
2. View video.
4. 2. Enter a name for your device.
3. You can tap the video window while viewing to enlarge it and go to view video.
3. Select the system...
User Guide - Page 46
...scheduled time.
The camera's signal status icon shows no bars
The camera's signal status icon shows one or two bars or the video quality is poor
Try..
• ...receiver and there is plugged in another program
I can't play in players such as Windows Media® Player if an H.264 CODEC plug-in Camera Setup (see
"Camera On" on page 8.
• The video files play with your camera...
User Guide - Page 47
...button to be on , the monitor's LCD screen will unlock the screen.
47 Try.. • making sure the camera is plugged in and the red LED is no icons. Screen lock may be on but...receiver and cameras for the first time, they seem to turn the LCD back on.
• tapping the Power button on . • pressing and releasing the pairing button quickly.
The camera won't pair with the receiver...
User Guide - Page 50
...or more of at least 20 cm (7.9") from the receiver. •• Plug the equipment into an outlet on , the user is connected. •• Consult the dealer or an experienced ... for additional suggestions. If this device may cause harmful interference to which the receiver is encouraged to try to radio or television equipment reception, which can radiate radio frequency energy, and...
Similar Questions
How To Access Live Video From Uniden Guardian G455 Cameras Via Ipad
(Posted by xbSacki 9 years ago)
G755 Security System. Need Software For Internet Connection For Remote Viewing
Has anyone found any software programs that work with the G755 system ? The website that Uniden has...
Has anyone found any software programs that work with the G755 system ? The website that Uniden has...
(Posted by indianafishing 10 years ago)
Can I Use Uniden Guardian Video System To Alert Me Of Any Movement On My Camera?
I am thinking of buying a security system for my home and have chosen uniden G455. Is it possible ...
I am thinking of buying a security system for my home and have chosen uniden G455. Is it possible ...
(Posted by shakenferns 11 years ago)
Will My Uniden Security System Udwc25 Work W/ My Iphone App ?
(Posted by Jenn30 11 years ago)
Can The Guardian Cameras Pair With Multiple Base Stations?
Is it possible to have multiple base stations to view the same set of cameras? e.g. one unit upstair...
Is it possible to have multiple base stations to view the same set of cameras? e.g. one unit upstair...
(Posted by jlincli 11 years ago)