Troy-Bilt TB525 Support Question
Troy-Bilt TB525 Support Question
Find answers below for this question about Troy-Bilt TB525.Need a Troy-Bilt TB525 manual? We have 2 online manuals for this item!
Question posted by bkhoneycutt1 on June 23rd, 2013
Change Head To Add Another Implement
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Troy-Bilt TB525 Manual Pages
Operation Manual - Page 1
...at the time of the unit, please call the Customer Support Department to make changes at www.troybilt.com or www.troybilt.ca. When servicing, use only identical replacement... States or 1-800-668-1238 in Canada.
Operator's Manual
Electric Start Capable 4-Cycle Gas Trimmer
TB525 EC
TABLE OF CONTENTS Service Information 1 Rules for Safe Operation 2 Know Your Unit 4 Assembly Instructions...
Operation Manual - Page 2
...Wear ear/hearing protection when operating this tool for proper accident prevention measures. If it to the head, hands and feet. • Clear the area of such materials.
• Always stop the... MEANING
SAFETY ALERT: Indicates danger, warning or caution. Do not smoke.
• Always add fuel in contact with loose or damaged parts.
• Carefully inspect the area before starting...
Operation Manual - Page 4
... to the
location that your unit is equipped with. Cutting Shield
2.
INSTALLING THE CUTTING HEAD SHIELD
1. Tighten the bolt until the threaded Square Bolt end protrudes through the hole until...2)
(15.24 cm) Minimum
Bolt
Fig. 2
EZ-Link™
Line Cutting Blade Cutting Head Shield
Cutting Head
4 Rotate the shield into the slot on your unit is not installed.
TOOLS REQUIRED: ...
Operation Manual - Page 5
...fuel is the primary reason for spilt fuel. As little as ethanol, methanol or MTBE (ether). Add 0.8 oz. (23 ml) of fuel additive per gallon of oil. OIL AND FUEL INFORMATION
WARNING... the tank.
3. Failure to the unit, put oil in the crankcase is extremely flammable. See Changing the Oil.
Wipe up in a clean, well ventilated outdoor area. Alcohol-blended fuel absorbs water....
Operation Manual - Page 6
... the crankcase. Run the unit for 30-60 seconds. Carbon monoxide exhaust fumes can be seen in the primer bulb (Fig. 8). Make sure that any Add-On item is properly warmed up for 2-5 minutes. Refer to squeeze the throttle control. If fuel cannot be lethal in the crankcase. Continue to Checking...
Operation Manual - Page 7
EZ-Link™ Coupler
Release Button
1. While firmly holding the add-on bare ground or hard soil.
Fig. 14
Each time the head is bumped, about 1 inch (25.4 mm) of trimming line ..., stand in the primary hole and
securely tighten the knob before
removing or installing add-ons. For best results, tap the Bump Head™ on , push it straight into objects such as opposed to the ground ...
Operation Manual - Page 8
... when checking and changing the oil (Fig. 25). Remove the cap either by tipping the unit to wind the line around the
dipstick before each side of the cutting head. (Fig. 19)
Fig. 19
NOTE: It may be just touching the O-Ring inner most thread on the oil fill hole, add a small
amount...
Operation Manual - Page 9
...authorized service dealer should not rotate when the engine idles.
3.
Remove the spark plug from the cylinder head by turning a 5/8 in . (.076 - 0.152 mm). If the clearance is adjustable. Turn ...engine idles, turn the idle speed screw counterclockwise 1/8 of the engine cover with a Flat-head or T-25 Torx® screwdriver (Fig. 36).
2.
Measure both valves are closed. Replace...
Operation Manual - Page 10
...mm) Trimming Line Diameter 0.095 inches (2.41 mm) Cutting Path Diameter, Trimmer Head 17 inches (43.2 cm)
* All specifications are sold separately.
Wipe off... (over 30 days)
Drain fuel tank and add fresh fuel
Fouled spark plug
Replace or clean the...been stored for any moisture with federal, state and local regulations. 5. Change the oil, referring to cool. in. (29 cc) Operating RPM ...
Similar Questions
How Do I Change The Head On Tb22ec Weedeater?
change head on older Tb22ec
change head on older Tb22ec
(Posted by Wbclarke 8 months ago)
How Do I Change Cutting Head On A Troybilt Tb625ec?
I can't figure out how to remove the old cutting head.
I can't figure out how to remove the old cutting head.
(Posted by dougclapp24 7 years ago)
Changing Trimmer Head On Troy-bilt Tb6044 Xp
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
(Posted by GCP1 8 years ago)
How To Remove Cutting Head
How To Remove Cutting Head From Tb525 Ec Trimmer
How To Remove Cutting Head From Tb525 Ec Trimmer
(Posted by godez 10 years ago)