Troy-Bilt TB525 Support Question
Troy-Bilt TB525 Support Question
Find answers below for this question about Troy-Bilt TB525.Need a Troy-Bilt TB525 manual? We have 2 online manuals for this item!
Question posted by godez on September 16th, 2013
How To Remove Cutting Head
How To Remove Cutting Head From Tb525 Ec Trimmer
Current Answers
Answer #1: Posted by TommyKervz on September 16th, 2013 3:32 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,833
Member since:
January 10th, 2013 Points: 17,776,833
http://www.helpowl.com/manuals/Troy-Bilt/TB525/187703
The pdf resource above should help.
Related Troy-Bilt TB525 Manual Pages
Operation Manual - Page 1
...obtain a list of printing. Service on this manual are based on our website at any time without notice.
Operator's Manual
Electric Start Capable 4-Cycle Gas Trimmer
TB525 EC
TABLE OF CONTENTS Service Information 1 Rules for Safe Operation 2 Know Your Unit 4 Assembly Instructions 4 Oil and Fuel Information 5 Starting and Stopping Instructions 6 Operating Instructions 7 Maintenance...
Operation Manual - Page 2
...668-1238 in CANADA
DANGER: Failure to the head, hands and feet. • Clear the ... carefully. These can
explode if ignited. Never remove the fuel tank cap or add fuel when the... using the unit, you are marked as a trimmer. Please keep these instructions before use of the ... Secure hair above shoulder level.
• The cutting attachment shield must be in effective working order, ...
Operation Manual - Page 3
....
• If you loan someone this unit. If you strike or become lodged between the cutting attachment and shield.
• To reduce fire hazard, replace a faulty muffler and spark arrestor.... vegetation and other users. Clean after the unit is delayed or when walking from one cutting location to off they remain hot for complete safety, assembly, operating, maintenance, and repair...
Operation Manual - Page 4
... that apply to the
location that your unit is secure. (Fig. 2)
(15.24 cm) Minimum
Bolt
Fig. 2
EZ-Link™
Line Cutting Blade Cutting Head Shield
Cutting Head
4 KNOW YOUR UNIT
APPLICATIONS
As a trimmer: • Cutting grass and light weeds. • Edging • Decorative trimming around
trees, fences, etc. Be sure the guard mounting bracket slides into...
Operation Manual - Page 5
... oil in a clean, well ventilated outdoor area. See Changing the Oil. Next, cut the tip off the funnel spout (Fig. 3).
Remove the fuel cap (Fig. 6).
2. It has been proven that may have spilled...fresh fuel (less than 10% ethanol will inhibit corrosion and minimize the formation of oil and remove the paper seal covering the opening. Keep
sparks and open flames at least 30 ft. (9.1...
Operation Manual - Page 6
.... SQUEEZE and HOLD the throttle control for 2-5 minutes. Press and hold the electric starter or drill ON (I) button for 2-second intervals until the unit starts. Remove the electric starter or drill from the unit.
10. Continue to Position 3 (Fig. 8).
12. Move the choke lever to squeeze the throttle control. Continue to...
Operation Manual - Page 7
... unit. For best results, tap the Bump Head™ on installation or removal easier.
90˚ Edging Hole (Trimmer Only)
1. If line release is released. Always keep the trimming line fully extended.
Move either in small increments to avoid premature line wear or engine drag.
• Cutting from :
• Entanglement with more than the...
Operation Manual - Page 8
... unit to wind the line around the
dipstick before each side of the cutting head. (Fig. 19)
Fig. 19
NOTE: It may be a need to get a proper oil level reading (Fig. 23). NOTE: Some maintenance procedures may be a need to remove the old line prior to federal, state and local regulations. NOTE: Maintenance...
Operation Manual - Page 9
...the engine idles.
3. Release the throttle trigger and let the engine idle. NOTE: The cutting attachment should make carburetor adjustments.
ROCKER ARM CLEARANCE
View Of The Rear Engine Cover
WARNING: To...until the tab on the air filter backplate snaps into place in the cylinder head. If using a feeler gauge (Fig. 36).
5. Remove the six (6) screws on the air filter cover (Fig. 29). Fig. ...
Operation Manual - Page 10
... kerosene, can damage plastic housing or handle. If choosing to start the trimmer after storage. 4. SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement 1.8 cu. Remove the spark plug and put 5 drops of the old oil in cutting head
Clean and thoroughly dry the cutting head
If further assistance is above 90˚ F
Move the choke lever to...
Parts Diagram - Page 2
MODEL TB525EC
4-CYCLE GAS TRIMMER
PPN 41EDT52C966
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Part No. 753-06134 753-04595 791-181003 ...
Parts Diagram - Page 3
MODEL TB525EC
4-CYCLE GAS TRIMMER
PPN 41EDT52C966
5
1
4
1 26
3
8
Item
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Part No.
753-04234 791-182690 753-...
Similar Questions
How Do I Remove The Cutting Head Of The Tb625 Ec Trimmer
head removal instructions.
head removal instructions.
(Posted by Anonymous-150877 8 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)
