Home » TP-Link » Wireless » TP-Link TL-WA5210G

TP-Link TL-WA5210G Support Question

Find answers below for this question about TP-Link TL-WA5210G.
Need a TP-Link TL-WA5210G manual? We have 1 online manual for this item!

TP-Link Overview Questions Manuals Reviews Videos Research

Question posted by jefTG on February 18th, 2014

How To Use Tl-wa5210g As A Repeater

The person who posted this question about this TP-Link product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related TP-Link TL-WA5210G Manual Pages

TL-WA5210G V1 QIG 7106503701 - Page 1

... placed face to Appendix 1. 1 Note The typical connection for TL-WA5210G is used for remote point-to-point connection. Here shows several incorrect examples. Please make sure that the two CPEs are using an external antenna to connect, please refer to face, otherwise the wireless signal strength might be weak. It makes remote internet share...

TL-WA5210G V1 QIG 7106503701 - Page 2

Tighten the straps. Note To get a best signal, you can refer to a PC using another Ethernet cable. Then, connect the LAN port of the CPE and then around the pole. Finally, plug the provided power ... steel structures will not obstruct the antenna signals and which offers maximum line-of the CPE. 2 Connecting the device Note Please use only wired network connections to configure the AP.

TL-WA5210G V1 QIG 7106503701 - Page 3

... to build the network, please make sure that the two CPEs are finished. The connection will be similar to the figure below describes. If you use two CPEs to face. Solid light Solid light or flashing Solid light Note If the LEDs display abnormally, please check to see if all your...

TL-WA5210G V1 QIG 7106503701 - Page 5

A. If you want to set it as a repeater, please skip to your WISP. c) If you want to set up a point-to-point connection with TL-WA5210G, please skip to your WISP. 5 Choose your WAN Connection Type provided by your WISP, please choose AP Client Route2r mode and proceed to AǗ b) If ...

TL-WA5210G V1 QIG 7106503701 - Page 6

... take effect after rebooting. Configuration for Point-to-Point Connection Note Two TL-WA5210Gs are needed for this application. 1) The AP Setting Select AP Click ... automatically. Click Finish 6 Click Finish B. however, choose a name that is easily remembered by your wireless network; The changes will take effect after rebooting. Here we enter TP-LINK_900008 as the SSID for ...

TL-WA5210G V1 QIG 7106503701 - Page 7

C. Configuration for Repeater To make sure the TL-WA5210G is under AP mode, please follow the steps below . 2) The Client Setting Note You should change the default LAN IP ... from 2 to 253) to avoid an IP conflict with the former AP. Here we choose 192.168.1.2 as an example. Click Wireless > Wireless Mode Select Client Enter TP-LINK_900008, the SSID of the first AP you click Save.

TL-WA5210G V1 QIG 7106503701 - Page 8

... Antenna Alignment 8 Click Wireless > Wireless Mode Select Repeater Click Survey This page will then display. Antenna Alignment After basic configuration of operation mode, you want to the parameters shown ...Save at the bottom of the remote AP that you can change your CPE's direction to get a better signal strength according to repeat, and then click Connect on the Antenna Alignment page.

TL-WA5210G V1 QIG 7106503701 - Page 9

...range as the following steps: Connect one side of the TL-ANT24SP to the RP-SMA port of your CPE directly. 2. See the Troubleshooting T3 if you need...Connect the other side of the TL-ANT24SP to assign your CPE through the TL-ANT24PT3. If you have any external antennas, you could choose TL-ANT2424B (external antenna), TL-ANT24SP (Surge Protector), and TL-ANT24PT3 (Pigtail Cable) to connect...

TL-WA5210G V1 QIG 7106503701 - Page 10

Enter the default values and click OK. User name: admin Password: admin Click OK Configure the external antenna Click Wireless Setting Select External Click Save ' 10 Login Open your web browser and type in http://192.168.1.254 in the address bar and press Enter A dialog box will prompt you for the User name and Password.

TL-WA5210G V1 QIG 7106503701 - Page 11

T2. What can I do that, please refer to previous section T1; 2) Use the default user name and password: admin, admin; 3) Try to reconfigure your computer's IP Address. T3. Hold it . Click Network and Internet Connections 11 If ...

TL-WA5210G V1 QIG 7106503701 - Page 13

Select Use the following IP address Enter the 192.168.1.100 into the IP address field, 255.255.255.0 into the Subnet mask field Select Use the following DNS server addresses Enter the DNS server address provided by your ISP or network administrator Click OK For Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks 13

TL-WA5210G V1 QIG 7106503701 - Page 15

TL-WA5210G V1 QIG 7106503701 - Page 16

... Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp „ For all other technical support, please contact us by using the following details: Global Tel: +86 755 26504400 E-mail: [email protected] Service time: 24hrs, 7 days a week Singapore Tel: +65 62840493 E-mail: support.sg...