TP-Link TL-WA5210G Support Question
TP-Link TL-WA5210G Support Question
Find answers below for this question about TP-Link TL-WA5210G.Need a TP-Link TL-WA5210G manual? We have 1 online manual for this item!
Question posted by pinakitplink on March 27th, 2014
Internet Share Between Two Tl-wa5210g Cpe
I Have Two Houses, Distance Is About 800 Foot. I Have Tp-link Tl-wa5210g Outdoor Cpe And 5110g Cpe. I Have A Broadband Connection On Bsnl Adsl Modem Router. i Want To Send My Internet Connection Through Those Cpe To One To Another House.
Current Answers
Answer #1: Posted by TheWiz on March 27th, 2014 8:03 AM
TheWiz
Member since:
October 13th, 2011 Points: 25,383,424
Member since:
October 13th, 2011 Points: 25,383,424
Sorry but it only works up to 200ft. There isn't any way of reliably sharing an internet connection between houses that are 800ft appart. Even a standard Cat6 ethernet cable has a max length of about 328ft. Unfortunately you would need to pay for internet service seperately for each house.
Related TP-Link TL-WA5210G Manual Pages
TL-WA5210G V1 QIG 7106503701 - Page 1
... typical connection for TL-WA5210G is used for remote point-to-point connection.
Note If you are placed face to Appendix 1. 1 Please make sure that the two CPEs are using an external antenna to connect, please refer to face, otherwise the wireless signal strength might be weak. 1 Typical network
TL-WA5210G is shown as above.
It makes remote internet share possible...
TL-WA5210G V1 QIG 7106503701 - Page 2
Tighten the straps.
Then, connect the LAN port of the CPE. Adjust the direction of your CPE for your CPE. Connect one end of an Ethernet cable to the POE port of the provided Power Injector and the other end to a PC using another Ethernet cable. ...
TL-WA5210G V1 QIG 7106503701 - Page 3
... build the network, please make sure that the two CPEs are placed face to the figure below describes.
Solid light Solid light or flashing Solid light
Note If the LEDs display abnormally, please check to see if all your device. 3 The connection will be similar to face. Turn on the AP display...
TL-WA5210G V1 QIG 7106503701 - Page 5
... Operation Mode Type appropriate to set it as a router, please choose AP Router mode, and for AP Client Router Mode
This page will then display.
a) If you want to connect to your WISP, please choose AP Client Route2r
mode and proceed to AǗ
b) If you want to set up a point-to-point connection with TL-WA5210G, please skip to C. A.
TL-WA5210G V1 QIG 7106503701 - Page 6
... wait until the AP completes rebooting automatically. The changes will take effect after rebooting. Click Finish
6 Configuration for Point-to-Point Connection Note Two TL-WA5210Gs are needed for this application. 1) The AP Setting
Select AP
Click Next
Enter a unique name for example Select your wireless network; Enter the SSID provided by network users.
TL-WA5210G V1 QIG 7106503701 - Page 7
C.
Click Wireless > Wireless Mode Select Client Enter TP-LINK_900008, the SSID of the first AP you have configured Click Save at the bottom ... AP will begin rebooting automatically after you click Save.
7 Click Network Enter 192.168.1.2 in , configure the other TL-WA5210G by following the steps below . After successfully logging in the IP Address field Click Save Note The AP will begin ...
TL-WA5210G V1 QIG 7106503701 - Page 8
... BSSID of the remote AP that you can change your CPE's direction to get a better signal strength according to repeat, and then click Connect on the Antenna Alignment page.
Then click Save at the bottom of the line.
Click Wireless Click Antenna Alignment
8 Click Wireless > Wireless Mode Select Repeater
Click Survey This page will then...
TL-WA5210G V1 QIG 7106503701 - Page 9
... address. See the Troubleshooting T3 if you are recommended to the RP-SMA port of your CPE directly.
2. You could connect it to use TP-LINK products for outdoor solution. If you have any external antennas, you need to the TL-ANT2424B.
2 Configure the external antenna
Note
You will need assistance.
9 Appendix 1: External antenna installation
1 External...
TL-WA5210G V1 QIG 7106503701 - Page 10
User name: admin Password: admin
Click OK
Configure the external antenna
Click Wireless Setting
Select External
Click Save
'
10 Login
Open your web browser and type in http://192.168.1.254 in the address bar and press Enter A dialog box will prompt you for the User name and Password. Enter the default values and click OK.
TL-WA5210G V1 QIG 7106503701 - Page 11
What can I do if I restore my AP's configuration to reconfigure the router.
For Windows XP OS Go to Start > Control Panel, you will then see the following the instructions of this QIG. Click Network and Internet Connections
11 Hold it for about 8 seconds
Note Once the AP is reset, the current configuration settings will...
TL-WA5210G V1 QIG 7106503701 - Page 14
Click Change adapter settings
Right-click Local Area Connection Click Properties
Double-click Internet Protocol Version 4 (TCP/IPv4)
14
TL-WA5210G V1 QIG 7106503701 - Page 16
... Friday
9:00 -12:00 ; 13:00 -18:00 *Except public holidays
Germany / Austria Tel: +49 1805 875465 (German Service) / +49 1805 TPLINK E-mail: support.de@tp-link.com Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42 EUR/min from mobile phone Service time: Monday to Friday...
Similar Questions
Connecting To Wireless Network With Cpe Tl-wa5210g, Can Chage Mac Adress?
(Posted by sundactvos 9 years ago)
How To Put Router Password On 54m Wireless Adsl2 Modem Router
(Posted by kfkrenkfo 9 years ago)
Cannot Access Tp-link Tl-wa5210g Cpe Web-based Utility
(Posted by prdavis0 9 years ago)
How To Block Website On Td-w8901g 54m Wireless Adsl2 Modem Router
(Posted by Vinosc 10 years ago)
I Want To Use My Tp-link Tl-wa5210g Cpe As A Repeater ,how Do I Do It
am an isp trying to set a wireless repeater so that another client can access the networ witout sett...
am an isp trying to set a wireless repeater so that another client can access the networ witout sett...
(Posted by africentisp 10 years ago)