Sony HCD-SH2000 Support Question
Sony HCD-SH2000 Support Question
Find answers below for this question about Sony HCD-SH2000.Need a Sony HCD-SH2000 manual? We have 1 online manual for this item!
Question posted by pickclayton on November 9th, 2017
No Sound Output
outmy spny sh2000 used to go in protect mode but doesn't anymore. Now it goes on and stays on but doesn't give any sound output on any source. It only makes a kick sound every 5seconds and sounds like its on a radio station with no signal.I really love this system. I really need help urgently please anyone.
Requests for more information
Request from lankainnovative on February 1st, 2024 8:49 PM
Also I have SH2000 with no sounds please help me to repair it
Also I have SH2000 with no sounds please help me to repair it
Current Answers
Answer #1: Posted by waelsaidani1 on November 9th, 2017 2:12 PM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
hello refer here to solve this problem: https://us.en.kb.sony.com/app/answers/detail/a_id/38388/c/65,66/p/41901,41902,70310/
Related Sony HCD-SH2000 Manual Pages
Service Manual - Page 1
...: Continuous Laser Output*: Less than 88 dB
Tuner section FM stereo, FM/AM superheterodyne tuner Antenna:
FM lead antenna AM loop antenna
FM tuner section Tuning range
87.5 MHz - 108.0 MHz (50 kHz step)
CD
CD Mechanism Type
CDM86B-DVBU101
Section
Optical Pick-up Block with 7 mm aperture. HCD-SH2000
SERVICE MANUAL
E Model...
Service Manual - Page 2
HCD-SH2000
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to use these instruments. 2. Check leakage as ...Precision 245 digital multimeter is 0.75 V, so analog meters must not exceed 0.5 mA (500 microamperes).
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS ...
Service Manual - Page 3
... DMB21 Board 8 2-5. Block Diagram - Schematic Diagram - Schematic Diagram - DAMP Board (Component Side 37 5-23. VOLUME Board 46 5-32. CDM Section 69
7. HCD-SH2000
TABLE OF CONTENTS
1. Block Diagram - Printed Wiring Board
- MAIN Board (4/4) (Suffix 11) -... 27 5-13. Schematic Diagram - AUDIO-IN Board 51 5-37. ELECTRICAL PARTS LIST 70
3 Schematic...
Service Manual - Page 4
...result in the repair parts.
HCD-SH2000
Ver. 1.1
SECTION 1 SERVICING NOTES
Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be in MPEG 1 Audio Layer 3 format.
2) A logical format...
Service Manual - Page 5
HCD-SH2000
5
disc
- Please rotate the pully in the midway of the arrow and eject the disc. SUFFIX-11 : 1-883-863-11 SUFFIX-12 : 1-883-863-12
... 2 DISASSEMBLY". CD mechanism block bottom view - MAIN BOARD DISCRIMINATION In this set, the MAIN board has been changed in the direction of production. MAIN Board (Component Side) -
Service Manual - Page 11
... the set .
11 ously and hold for 3
seconds. 3. SECTION 3 TEST MODE
HCD-SH2000
PANEL TEST MODE This mode is used to check operations of 0, 9, 8, 7 ... Press @/1 button to initial conditions. Procedure: 1. In the key check mode, the fluorescent indicator tube displays "K 0 V0". When you press [SOUND FLASH] button again, another half of each category software in the...
Service Manual - Page 13
... Frequency of automatic scanning means "The station signal is 75 ohm.
3. Set to FM
antenna input directly. You cannot use SG whose output impedance is received in good condition". Please use video cable for checking.
HCD-SH2000
13 TUNER SECTION 0 dB = 1 ȝV FM AUTO STOP CHECK
SECTION 4 ELECTRICAL CHECK
signal generator
set .
Input the following...
Service Manual - Page 14
HCD-SH2000
• Circuit Boards Location
SECTION 5 DIAGRAMS
DAMP board
MS-214 board TUNER MAIN board
DMB21 board SWITCHING REGULATOR
DISPLAY board BUTTON board
MIC board
BUTTON LED board VOLUME LED board USB board
VOLUME board AUDIO-IN board
14
Service Manual - Page 16
SIGNAL PATH
: AUDIO : TUNER (FM/AM) : MIC
HCD-SH2000
16
16 J1300 MIC IN
A (Page 15)
L-OUT
J1200
TV R-CH
J1201
PC
GAME AUDIO IN
DVD/SAT AUDIO IN
J500 L R L R
R-CH R-CH R-CH
IC1300 MIC AMP
5
7
3
1
RV1300
MIC LEVEL MIN MAX
IC501 OP AMP
5
7
46 MIC
39 ...-OUT 11
X113 8MHz
X110 32.768kHz
R-ch is omitted due to same as L-ch. BLOCK DIAGRAM - MAIN Section - HCD-SH2000
5-2.
Service Manual - Page 17
... INPUT+ 3
R-CH
AMPLIFIER IC503
5 INPUT+ OUTPUT 1
7 OUTPUT INPUT+ 3
3 INPUT+ OUTPUT 1
MUTE Q601
OP AMP IC805
5 INPUT+ OUTPUT 7
C Lch
(Page 16)
R-CH
3 INPUT+ OUTPUT 1
MUTE Q600
OP AMP IC600
5 INPUT+ OUTPUT 7
SIGNAL PATH
: AUDIO
MUTE Q207
51
/LINE-MUTE DAMP-CLK /DAMP-RESET
NO USE /SD-SLOW RESONANCE
D1403 D1435
HCD-SH2000
LOW SPEAKER IMPEDANCE USE 4ȍ
2 INA- AOUT 1
PREAMP IC1403...
Service Manual - Page 19
...Signal path. Note: The components identified by mark 0 or dotted line with part number specified.
• A : B+ Line. • B : B- F : AUDIO E : USB f : TUNER J : AUDIO (DIGITAL)
• Abbreviation...Saudi Arabia model MX : Mexican model MY : Malaysia model SAF : South African model
HCD-SH2000
19
19
HCD-SH2000
Ver. 1.1
no mark : TUNER < > : CD PLAY
* : Impossible to ...
Service Manual - Page 20
...Page 37)
B
DAMP BOARD CN1401 (Page 37)
J
HCD-SH2000
20
20
Note: Refer to the servicing notes "MAIN BOARD DISCRIMINATION" (page 5) for Circuit Boards Location. • : Uses unleaded solder.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
B
TUNER
J BOARD
CN1601 (Page 49)
C
(".&
"6%*0 */
-
3
D
%7%4"5
"6%*0 */
-3
E
- MAIN BOARD (Component Side) (Suffix-11) - • See...
Service Manual - Page 22
...
A BOARD CN1000 (Page 45)
AUDIO-IN
H BOARD NO1200 (Page 51)
12 (12)
(CHASSIS)
G
DAMP BOARD CN1400 (Page 37)
B
DAMP BOARD CN1401 (Page 37)
J
HCD-SH2000
Note 1: Refer to the servicing notes "MAIN BOARD DISCRIMINATION" (page 5) for Circuit Boards Location. • : Uses unleaded solder.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
MAIN BOARD (Component side)
B
TUNER
J BOARD...
Service Manual - Page 27
... OUTPUT INPUT+ INPUTGND INPUT+
IC502 BPF BA4558F
CN106 7P
IC502
E
TV IN-L 1
JL201
TV IN-L
1234
A-GND 2
4.5 4.5 4.5
H
TV IN-R 3
JL202
TV IN-R
C659 0.1
AUDIO...
JL732 R745 JL731 R744
0 78 0 77
HCD-SH2000
27
27 OUTPUT INPUT+ INPUTGND INPUT+
IC503 BPF BA4558F
BB1L ...0.22
AGCOUTL
35 TREL 36 RECBL
IC B/D
IC500
IC500 SOUND CONTROL
R2A15216FP
BASS2R 14 BASS1R 13
MID2R 12 MID1R 11 ...
Service Manual - Page 31
...for IC Block Diagrams.
1
2
3
4
5
6
7
8
HCD-SH2000
9
10
11
12
13
14
15
A
MAIN BOARD (4/4)
29... 0.22
AGCOUTL
35 TREL 36 RECBL
IC B/D
IC500
IC500 SOUND CONTROL
R2A15216FP
BASS2R 14 BASS1R 13
MID2R 12 MID1R 11 TRER...R867 0
JL602 JL603
C726 0.47
WHT J500
DVD/SAT
AUDIO IN
RED
L
R
33k 0.1
OUTPUT VCC INPUT- OUTPUT INPUT+ INPUTGND INPUT+
IC502 BPF BA4558F
CN106 7P
IC502
...
Service Manual - Page 57
...-SAMPLER
DECIMATION FILTERS
AUDIO INPUT PORT
RATE ESTIMATOR
AUDIO OUTPUT
PORT
BYPAS 9 IFMT0 10 IFMT1 11 IFMT2 12
RST 13 MUTE 14
CONTROL LOGIC
28 MODE2 27 MODE1 26 MODE0
25 BCKO 24 LRCKO 23 SDOUT
22 VDD 21 DGND
20 TDMI
19 OFMT0 18 OFMT1 17 OWL0 16 OWL1 15 RDY
HCD-SH2000
57
Service Manual - Page 61
...recovery
47
AUDIO-DATA
O Serial data output to audio signal processor, R2A15216FP
48
NO-USE
O Unused
49
AUDIO-CLK
O Serial data transfer clock signal output to LED... for several hundreds msec and then change to "H".
13
XOUT
O Main system clock output terminal (8MHz)
14
VSS
- HCD-SH2000
• IC Pin Function Descriptions MAIN BOARD (1/4) IC100 R5F3650KBDFA (SYSTEM CONTROL)
Pin...
Service Manual - Page 63
...output to the flash ROM
O Serial data transfer clock signal output to the system controller
O Serial data output to the system controller
I ICE mode enable setting terminal Not used... output to the SD-RAM
O Clock signal output to the SD-RAM
O Address signal output to the SD-RAM
- Power supply terminal (+3.3V)
I RF sub beam (E) input from the optical pick-up block
- HCD-SH2000
DMB21...
Service Manual - Page 64
HCD-SH2000
Pin No. 69 to 74
75 76 77 78 79 80 81 to 83 ...O Row address strobe signal output to the SD-RAM
O Bank address signal output to the system controller
- Power supply terminal (+3.3V)
O Component video (Y) signal output terminal Not used O Component video (Pb/Cb) signal output terminal Not used O Component video (Pr/Cr) signal output terminal Not used
- Power supply terminal (+3....
Service Manual - Page 70
... SWITCH, TACTILE (ISOLATOR) SWITCH, TACTILE (SEARCH) SWITCH, TACTILE (SOUND FLASH)
S1255 S1256 S1257 S1258 S1259
1-771-410-21 1-771-410-... from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized...CHIP 0
D1280 6-503-224-02 DI 1L0352V22F3MIT02
70 HCD-SH2000
Ver. 1.1 AUDIO-IN BUTTON
BUTTON LED
SECTION 7 ELECTRICAL PARTS LIST
Note...
Similar Questions
Hcd Sh2000 Sony
I have HCD SH 2000 it's has no audio out in any Chanel ( first it was on protection mode then now it...
I have HCD SH 2000 it's has no audio out in any Chanel ( first it was on protection mode then now it...
(Posted by Sehar517 1 year ago)
Speaker Wire Connector
looking for part number: 1-839-129-11 and 1-839-128-2
looking for part number: 1-839-129-11 and 1-839-128-2
(Posted by Crsj1981 2 years ago)
When I Turn On My System It Goes Right Into Protect Mode.. I Need Help
whelp when I turn it on it is good for like 3 seconds and then it goes to protect mode and I cannot ...
whelp when I turn it on it is good for like 3 seconds and then it goes to protect mode and I cannot ...
(Posted by Mrfire81 2 years ago)
I Need Help With Sony Str-kg700
I need help please.. I have a sony home theater system a sony the model number is STR-KG700 I only h...
I need help please.. I have a sony home theater system a sony the model number is STR-KG700 I only h...
(Posted by Singleandhurt19 4 years ago)