Home » Sanyo » Flat Panel Televisions » Sanyo DP42849

Sanyo DP42849 Support Question

Find answers below for this question about Sanyo DP42849 - 42" LCD TV.
Need a Sanyo DP42849 manual? We have 4 online manuals for this item!

Sanyo Overview Questions Manuals Reviews Videos Research

Question posted by tmehcapt on August 26th, 2014

How To Update Firmware On A Sanyo Dp42849?

The person who posted this question about this Sanyo product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Sanyo DP42849 Manual Pages

Owners Manual - Page 2

...) that the cable ground shall be connected to the grounding system of the building, as close to keep from tip-over. 13. "Note to the television equipment, be located in particular, specifies that produce heat. 9. Keep these instructions. 2. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN! A grounding-type plug has two...

Owners Manual - Page 3

...of the following measures: - However, there is designed and manufactured to radio or television reception, which the receiver is Listed by one or more information visit www.energystar.gov... a trademark of fire, casualty and electrical hazards. PC RESOLUTION CHART SANYO recommends keeping the TV set at its factory settings or moving Energy Saver settings from Dolby Laboratories. For more...

Owners Manual - Page 4

...OPERATION 7 BACK PANEL JACKS 8 AUDIO / VIDEO CONNECTIONS 9 POWER CONNECTION / INITIAL CHANNEL SEARCH . .10 SPECIFICATIONS Power Requirement: Source: AC 120V, 60Hz AC Power Consumption: DP42849 216 watts DP46849... use hard objects such as hard cloth or paper. POSITIONING THE LCD HDTV Always use a firm-flat surface when positioning your HDTV. Remote Control Battery Installation 5 Antenna ...

Owners Manual - Page 5

...-877-5032 5 It can receive digital and analog off air signals from a direct Cable TV connection. CAUTION: Hold the stand firmly as you remove the last screw. 2 Use the...Diameter, Length-16mm (maximum) 1 Remove the four (4) screws securing the foot stand. DP42849 DP46849 DP52449 1 Remove the four (4) screws securing the foot stand. Wall mounting of explosion if a battery is replaced...

Owners Manual - Page 6

..." (included in separate folded sheet) to program the GXDB remote to control your remote control the Sanyo TV control code is dedicated only to use, compact remote control. NOTE: "TV" mode is reactivated. Press... By pressing the TV key on pages 19 - 22 of this owner's manual. To... 6 Need help? Advanced programming instructions for...

Owners Manual - Page 7

... - PC Sound Standard - Note: Power on the computer. Move the image horizontally V-Position - Stereo mini audio cable HDTV BACK PC OR LAPTOP RGB Monitor cable Sanyo recommends using a monitor cable that includes a Ferrite Core. Adjust the screen's Contrast, Brightness and Color Temperature settings. Manual - Adjust the HDTV's Bass and Treble settings...

Owners Manual - Page 8

High Definition image available from HD signals and HD equipment. 8 Need help? www.sanyoctv.com 1-800-877-5032 BACK PANEL JACKS 1 Digital Audio Output (Coaxial) 1 2 Component Video Input (VIDEO2 or VIDEO3) Green (Y), blue (Pb), and red (Pr) Video inputs plus the white and red Audio ...

Owners Manual - Page 10

...Access an on screen trouble shooting guide (in AC power cord 120V AC, 60Hz Turn On TV Wait for signals from devices connected to input Video1. An AV search will begin if no ...sanyoctv.com 1-800-877-5032 GETTING STARTED- CHANNEL SEARCH Checks Antenna and Cable signals connected to the TV before comencing an AV Search. INITIAL CHANNEL SEARCH (FIRST POWER ON) Plug in the Initial Setup...

Owners Manual - Page 14

...or previous value that you wish to save power consumption. You may also set Switch on Time to ON, the TV will automatically turn on at the previously set a Switch on Time. The higher the level number, the more ... ON-SCREEN MENU OPERATION SETUP (CONTINUED) ENERGY SAVER Energy saver settings control the LCD backlight brightness to change. www.sanyoctv.com 1-800-877-5032

Owners Manual - Page 17

...SCREEN Need help? Choose Start Slideshow after pressing ENTER on a thumbnail photo to start the slideshow from the settings in TV and AV inputs. NOTE: Picture Settings are separate configurations from the current picture. Press ENTER to USB Input when ... with the use of a USB mass storage device. USB DEVICE HDTV BACK PANEL NOTE: The HDTV switches to show the full view options menu.

Owners Manual - Page 18

... function of the Xacti must also be turned off by turning off the TV set, or setting the device on stand-by as often than a common 60 Hz refresh rate TV would. MOTION SYNC (120 Hz) *DP52449 only Your Sanyo 52" HDTV DP52449 has a refresh rate of 120 Hz, it basically means that...

Owners Manual - Page 19

... unusual formats. G Learned keys are low, or the remote has a memory fault. Count the red LED blinks (for three seconds, suggesting the remote is approximately 42 to your batteries are mode-specific, so each mode. ing order for Learning: DEVICE KEYS, SET, or RECORD (G) G Learning capacity is ready to learn functions...

Owners Manual - Page 20

...change the Volume Lock setting to Global Volume Lock so that you want to control (for example, TV.) 4. Press and hold SET until the LED blinks twice, then release. 3. Enter 9 9... PROGRAMMING CHANNEL LOCK Channel control can also delete learned programming by users who watch all broadcast TV through one device's volume controls volume in all other modes. Press the key containing the ...

Owners Manual - Page 21

.... moved data from twice. Repeat steps 1-4 for example, control DVD functions while in TV mode and the TV changes channel accordingly). Press and hold SET until the LED blinks twice, then release. ... mode) or to a different key in the new mode that allows you want to . (e.g., TV). 6. Press the device key for each device you wish to the active operating mode, follow these...

Owners Manual - Page 22

... could program the macro key to turn on both your remote control the Sanyo TV control code is dedicated only to a Sanyo TV. The LED blinks twice. 3. Press and hold SET until the red..., but only if you are in DVD mode, this key does not execute the macro you selected in TV mode. PROGRAMMING A MODE-DEPENDENT MACRO 1. Press and hold SET until the LED blinks twice, then release....

Owners Manual - Page 23

... FIRST 90 DAYS from the date of original retail purchase, Sanyo Manufacturing Corporation will replace any manufacturing defect or malfunction Sanyo Manufacturing Corporation will provide a new TV via exchange at the sole discretion of purchase, Sanyo Manufacturing Corporation warrants this product to give us the television's model number and serial number when you call. To...

Quik 'N Easy Setup Guide - Page 1

... High Definition RF TERMINAL COMPOSITE Standard GOOD Quality Connections BETTER Quality Connections BEST Quality Connections QUALITY PICTURE High Definition QUIK 'N EASY Setup Guide Your SANYO High Definition Television can display great quality picture when: A High Definition signal is due to the same HDTV INPUT. HDMI cable The quality of the output jack...

Quik 'N Easy Setup Guide - Page 2

...VBCT PROTECTING YOUR HDTV's LCD SCREEN The screen can cause permanent discoloration or dark spots. Do not use hard objects such as hard cloth or paper. Sanyo Manufacturing Corp. 3333 Sanyo Road, Forrest City, AR...that the receiver is hooked up to it 's not maintained properly. Place the HDTV on a flat firm surface and allow adequate space on your HDTV's remote) NOTE: Tune to your Satellite ...

GXDB Remote Guide - Page 1

...Press and hold the 1 key to increase - ON TIMER Displays the On-screen Help menu with your Sanyo HDTV. Switch from one Video input source to open the Input List menu. NOTE: Hold for a... channel banner information. Scan through Tune to a channel directly. USB Switch directly to normal TV viewing. Displays SLEEP timer. Part No. 1JC6P1P0339-- Power On or power Off your HDTV ...