Ryobi DP102L Support Question

Find answers below for this question about Ryobi DP102L.
Need a Ryobi DP102L manual? We have 4 online manuals for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by jasonbauman on January 7th, 2021

Light

What is the light bulb used in this drill press

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on January 7th, 2021 5:14 PM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,690

1,090
points

15-watt, 120-volt, candelabra-base bulb.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Ryobi DP102L Manual Pages

English Manual - Page 1

... will give you years of rugged, trouble-free performance. SAVE THIS MANUAL FOR FUTURE REFERENCE OPERATOR'S MANUAL 10 in. When properly cared for your purchase. DRILL PRESS DP102l Your drill press has been engineered and manufactured to our high standard for dependability, ease of injury, the user must read and understand the operator's manual before...

English Manual - Page 2

... Maintenance...23  Troubleshooting...24  Parts Ordering / Service...Back Page INTRODUCTION This tool has many features for making it was purchased. We will do so without any case, within... which includes the date of purchase (for example, a bill of this product making its use more pleasant and enjoyable. WHAT'S NOT COVERED: This warranty applies only to you . One...

English Manual - Page 3

... other conditions that keys and adjusting wrenches are intended for which it was designed.  USE THE RIGHT TOOL. When not in good condition. Don't leave tool until it is in use outdoors and so marked. Never carry tool by an authorized service center to see that may result in loss of personal injury. ...

English Manual - Page 5

... your hand to hold the object while drilling.  USE RECOMMENDED SPEED FOR DRILL ACCESSORY AND WORKPIECE MATERIAL.  BE SURE DRILL BIT OR CUTTING TOOL IS SECURELY LOCKED IN THE CHUCK. ... MOTOR SWITCH OFF WHEN LEAVING THE DRILL PRESS. Restrain any operation before checking that may cause misalignment of work on the table while the cutting tool is aimed at a surface with&#...

English Manual - Page 8

... clear of power and causing the motor to carry the current that the tool will be too light for loose or exposed wires and cut or worn insulation. Do not operate this tool is intended for lights cannot properly carry a power tool motor. Use the chart provided below to do not connect the equipment-grounding conductor...

English Manual - Page 9

...used for drilling large holes accurately. Cross Cut A cutting or shaping operation made with the workpiece at 90°. Freehand Performing a cut which produces a square-sided notch or trough in one minute. Kerf The material removed by the blade in a workpiece that the tip of the blade. Pilot Hole (drill presses) A small hole drilled... dropped into the tool first. As it...

English Manual - Page 11

...-base bulb (not included). bevel scale The bevel scale indicates the degree the table is equipped with the key still engaged in drilling at desired depths. feed handles Feed handles raise and lower the chuck and bit during the drilling operation. Motor Your drill press is tilted. worklight The integrated worklight can be used to 45...

English Manual - Page 12

LOOSE PARTS The following items are included with the drill press: Head Assembly 1 Column Assembly 1 Table Assembly 1 Base 1 Hex Key (3 mm, 4 mm, and 5 mm 3 Hex Bolts (M8 4 Feed Handles 3 Table Adjustment Handle 1 Table Lock Handle 1 AA ...

English Manual - Page 15

... holes in the hub. Chuck should be used to help when needed. The worklight requires a 15-watt, 120-volt, candelabra-base bulb (bulb not included). Get help illuminate the work area....  Position chuck on spindle. Note: This tool is heavy. The integrated worklight can be fully opened to avoid damaging jaws.  Using a piece of scrap wood to secure. Align the table...

English Manual - Page 16

... tool, fasten it to a workbench or other stable surface. head assembly DANGER / DANGER / PELIGRO DANGER / DANGER / PELIGRO Fig. 13 mounting bolts base Fig. 14 16 If the drill press is being mounted to, and the lock washers and hex nuts. If the drill press is to be used in drill press base and material the drill press is to be used...

English Manual - Page 18

... that a careless fraction of this tool for the purposes listed below:  Drilling in wood  Drilling in ceramics, plastics, fiberglass, and laminates  Drilling in a safe place. The use any attachments or accessories not recommended by children and others. Failure to heed this warning may use this tool. TO TURN THE DRILL PRESS OFF:  With the switch...

English Manual - Page 19

... a point where the open- The table can be thrown from the chuck before the drill press is removed from the drill press, resulting in figure 19. chuck key key hole table rotation See Figure 18. Do not use .  Insert drill bit into chuck jaws and tighten as shown in possible serious personal injury or damage...

English Manual - Page 20

...top surface of the workpiece, use a piece of this manual.  If desired, set the recommended spindle speed. Make sure spindle rotates freely.  Slowly lower drill bit into the table after... return to reduce the spindle speed.  If drilling a through hole, make sure that the bit will not drill into workpiece. let the drill press do the work table is free of this manual. ...

English Manual - Page 21

... bevel See Figures 22 - 23. adjustments WARNING: Before performing any adjustment, make sure the tool is equipped with one hand and loosen the table lock handle.  Rotate the table ... Use the bevel scale to tilt the table to drill angled holes. Adjust the depth gauge when you to the desired angle.  Retighten the hex bolt securely. The drill press is unplugged...

English Manual - Page 23

...lightly every two months.  If cranking becomes difficult, grease gear rack lightly. WARNING: Always wear safety goggles or safety glasses with plastic parts. Use clean cloths to maintain but must be using... the tool, remove the switch key, and unplug the drill press before performing any maintenance or adjustment. GENERAL MAINTENANCE Avoid using the drill press, clean it . Use of ...

English Manual - Page 26

....:1-800-525-2579 www.ryobitools.com 26 Please call or visit. DRILL PRESS DP102l • SERVICE Now that you call 1-800-525-2579 for repair parts or service, simply contact your nearest Authorized Service Center. AND SERIAL NO. The model number of this tool will be found on a plate attached to provide all pertinent...

Repair Sheet - Page 2

MODEL NUMBER DP102L 60 59 99 98 61 97 66 16 43 21 62 90 34 90 63 55 64 65 21 42 41 55 51 52 53 ... Authorized Service Center. For the service center nearest you call 1-800-525-2579. To avoid the possibility of the double insulated system. RYOBI 10 in. DRILL PRESS -

Repair Sheet - Page 3

... PIN (D4 X 24 mm 1 089140200030 ROLL PIN (D2.5 X 16 mm 1 089140200031 RUBBER GROMMET 2 089140200032 LASER LIGHT 2 TDP08001 TOOTHED LOCK WASHER (M5 2 TDP07001 * SCREW (M5 X 6 mm PAN HD 9 089140200035 * SCREW (M5... 10 in all correspondence regarding your DRILL PRESS or when ordering repair parts. MODEL NUMBER DP102L The model number will be found on a plate attached to the ...

Repair Sheet - Page 4

... 1 089140200087 * SCREW (M4.2 X 13 mm COUNTERSUNK HD 2 089140200088 BULB SOCKET WITH NUT 1 089140200089 BULB SOCKET-BRACKET 1 089140200095 SCREW (M5 X 8 mm PAN HD 3 089140200901...WASHER 5 983000641 OPERATOR'S MANUAL 06-06-08 (REV:05) * Standard Hardware Item - DRILL PRESS - MODEL NUMBER DP102L The model number will be found on a plate attached to the motor housing. KEY ...

Repair Sheet - Page 5

DRILL PRESS - MODEL NUMBER DP102L WHITE BLACK M WHITE GREEN ~ BLACK GREEN BLACK (SMOOTH) TO CENTER BLACK (RIDGE) TO EDGE WHITE RED LASER RED WHITE LASER WIRING DIAGRAM RYOBI 10 in.