Ricoh Aficio MP C2030 Support Question
Ricoh Aficio MP C2030 Support Question
Find answers below for this question about Ricoh Aficio MP C2030.Need a Ricoh Aficio MP C2030 manual? We have 2 online manuals for this item!
Question posted by wandjicarlos on August 13th, 2017
Ricoh Error Code 400
I can not make more than 3 impressions because a third, the error code 400 is displayed and asks me to restart. And it restarts when I restart. Help me please
Current Answers
Answer #1: Posted by freginold on August 13th, 2017 4:55 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
sc400 is an image density error, and is often caused by a dirty ID sensor. The ID sensor board, which houses the ID sensors, is located on the right side of the copier, just above and to the right of the black photoconductor/developer unit. If you remove that unit, you can open the shutter for the ID sensors and clean them with either canned air or a damp lint-free rag.
Generally, cleaning the ID sensors and rebooting the copier will resolve an sc400 error. If it does not, you may want to call a service technician to diagnose the problem, because the ID sensor board may need to be replaced, but it could also be a problem with the image transfer unit or another component.
Generally, cleaning the ID sensors and rebooting the copier will resolve an sc400 error. If it does not, you may want to call a service technician to diagnose the problem, because the ID sensor board may need to be replaced, but it could also be a problem with the image transfer unit or another component.
Related Ricoh Aficio MP C2030 Manual Pages
Troubleshooting Guide - Page 2
... might not be slightly different from the supplier.
For details about power source, see "Machine Types", About This Machine.) • Type 1: MP 1600/Aficio MP 1600/IS 2316 • Type 2: MP 2000/Aficio MP 2000/IS 2320 Certain types might result from the supplier with your local dealer. For your machine before reading this manual are...
Troubleshooting Guide - Page 3
... the procedures for explanations on which country you want to this manual for registering administrators, as well as registering fax numbers, e-mail addresses, and user codes. i Also refer to do with , or prevent the machine from being tampered with the machine.
Troubleshooting Guide - Page 5
... Server-Generated Error E-mail 36
4. When the Machine Does Not Operate As Wanted
Indicators ...3 Panel Tone...4 When the Function Status Indicator Lights Up in Red 5 When You Have Problems Operating the Machine 6 When a Job Is Not Performed 9
2. Troubleshooting When Using the Copy Function
When a Message Is Displayed 11 When You Cannot Make Clear...
Troubleshooting Guide - Page 7
... find further relevant information. [ ] Indicates the names of keys that appear on the machine's display panel. { } Indicates the names of About This Machine.
They can be found in moderate or...This Machine. They can be found in the "Safety Information" section of keys on resolving user errors. This symbol is located at the end of data. Ignoring these notes could result in this ...
Troubleshooting Guide - Page 9
Appears when toner runs out. Appears when paper-out condition occurs.
See p.84 "Adding Toner".
3 h: Error indicator B: Load Paper indicator D: Add Toner indicator
Appears when there is a misfeed, a cover is left open, or another problem occurs. See p.65 "Loading Paper". See p....
Troubleshooting Guide - Page 11
...p.65 "Loading Paper".
An error has occurred. See "When a Message Is Displayed" of each chapter.
Record the code number shown in the display and contact your service representative.
...that appears. You can use other functions normally. connect to A network error has occurred. See "When a Message Is Displayed" of each chapter.
• Check that the machine is correctly connected ...
Troubleshooting Guide - Page 13
...Paper or
Two-Sided Paper". The user code entry screen is removed. ap-
Load paper... as required.
An error message remains, even if misfed paper is displayed. See p.71 "...Changing the Paper
Size".
Check the end fence is set the paper size. See p.89 "Removing Jammed Paper". See p.93 "Where to eight
agement. "Temperature Alert. and wait a while before restarting...
Troubleshooting Guide - Page 28
... initialized. Place original again, and then press the {Start} key.
Troubleshooting When Using the Facsimile Function
When a Message Is Displayed
This section describes the machine's main messages. If other
function. Message
Cause
Solution
Error occurred, A document jam occurred during Memory Place originals that have been stored. cancelled.
3
may be used.
Place original...
Troubleshooting Guide - Page 29
....
Confirm correct login user name
failed.
Contact the administrator. A network error has occurred and connection has failed. has failed. Make settings correctly for the user name and the password for Admin
destination(s) or Web Image Monitor. Exceeded max. Max.: nnn
(A figure is displayed. LDAP server search timed out.
Check the information of [System...
Troubleshooting Guide - Page 30
... name is correctly programmed. The sender has not been specified.
See the Web Image Monitor's Help.
• Contact your network administrator.
24 grammed using the Web Im-
Check whether there ...}
Cannot access the SIP server.
• Use your Web Image Monitor
ed by another device. Check whether there are cor- dress and user name are any entered is already registered on...
Troubleshooting Guide - Page 35
Make sure that you set "Receive documents by pressing the {Start} key when originals are not set." See "Con-
3
... fax docu-
Set [Maximum E-mail Size] under [Ement exceeds the maximum e-
If the machine fails to a "maximum email size" error. Press [Original Size:], select the scanning area, and then resend the document. If you cannot receive by the Contact the administrator. If...
Troubleshooting Guide - Page 36
....
If this happened when the Re- • Load paper into the paper tray.
but an error message does not appear.
Fax transmission. The number of Special Sender, Email TX Result, routing email... cancel an Im- Check if there are over the specified numbers registered in standby. tray. making printing impossible.
The toner has run out, • Add toner. correct.
30 See "...
Troubleshooting Guide - Page 40
... not received" column gives the number of pages. See "Parameter Setting", General Settings Guide.
❒ You can display a destination with the machine or noise on the telephone line. If an error occurs during reception, ask the sender to resend the document.
See "Parameter Setting", General Settings Guide.
34 Possible causes include a problem with...
Troubleshooting Guide - Page 42
... the originator of this notification is also
sent to the administrator's e-mail address when one is received via SMTP, the SMTP server sends error e-mail to send an Error Mail Notification.
Error Mail Notification
The machine sends the Error Mail Notification to the sender when it is unable to
successfully receive a particular e-mail message.
Troubleshooting Guide - Page 45
...Ready" appears on again.
Turn off the main power switch, and back on the display panel. Solution
Turn off , see "Turning On the Power", About This Machine....error may have occurred in the IEEE 802.11b board.
The machine settings are being changed.
When a Message Is Displayed
When a Message Is Displayed
This section describes the principal messages that appear on the display...
Troubleshooting Guide - Page 46
... printer driver, or select [Font Priority] in off the main power switch, and back on again.
NV-RAM Error
An error has occurred in the
Error
Ethernet board. Authentication failed.
• The login user name or pass- • Check your sales or service ...the specified paper
copier function. Memory Overflow Maximum capacity of PCL or
PostScript3 list display has been exceeded.
Troubleshooting Guide - Page 58
If the problem cannot be solved, contact your sales or service representative.
52 chine or deactivate those devices. cation error
might have
occurred.
• Interference
from close proximity with
ceeds the ca-
pacity of the machine.
•
If there are not high. tion speed.
• ...
Troubleshooting Guide - Page 64
.... If
work error occurred and the file the message is still shown, the
could not be crowded.
Make sure the protection code is incorrect. See "Registering a Protection Code", General Settings Guide...8226; Set [Divide & Send E-mail] to display the transmission results, and then check which job has not been sent. The correct protection code was invalid.
• Check that the user ...
Troubleshooting Guide - Page 106
...box not displayed, 54 Server-Generated Error E-mail, ...36 Shadow appears on copies, 13 Side fences, 71, 74, 79 Stamp cartridge replacement, 87 Status Messages, 39
T
Toner, 84, 85, 86 Transmission, 29 Transmission/Reception, 29 TWAIN, 60 Two-Sided Paper, 68
U
User code entry, 6
V
Volume adjustment, 19
W
Waste Toner, 86 When A is displayed, 89 When B is displayed, 89 When P is displayed...
Troubleshooting Guide - Page 108
Operating Instructions Troubleshooting
Type for MP 1600L/Aficio MP 1600L/IS 2316L Type for MP 2000L/Aficio MP 2000L/IS 2320L AE AE B843-7605
Similar Questions
My Printer Has A Error Code Sc397 What It Is
my printers/copiers model no : mp c2030 now it has showing a error code please tell me what to do?
my printers/copiers model no : mp c2030 now it has showing a error code please tell me what to do?
(Posted by wilnavindsouza19 9 years ago)
My Copy Machine Aficio Mp2000 The Paper Jam And Show Error Code Ac390 What I Do
my machine aficio 2000 the paper became jam and show error code ac 390 i dont know what i do kindly ...
my machine aficio 2000 the paper became jam and show error code ac 390 i dont know what i do kindly ...
(Posted by sailsayor 10 years ago)
Error Code Ricoh 2030 Model
hi my printer ricoh 2030 show error sc 878 how to remove this error code pls tell
hi my printer ricoh 2030 show error sc 878 how to remove this error code pls tell
(Posted by sujitsinha007 10 years ago)
