Pioneer GM-5500T Support Question
Pioneer GM-5500T Support Question
Find answers below for this question about Pioneer GM-5500T.Need a Pioneer GM-5500T manual? We have 1 online manual for this item!
Question posted by Chanpjkae on August 25th, 2014
If You Are Using A Pioneer Gm-5500t Amp With A Single Channel Input Will It Run
full power mono?
Current Answers
Related Pioneer GM-5500T Manual Pages
Owner's Manual - Page 2
...Please keep the details
of headphones may invalidate the user's right to this product.
Pioneer Electronics (USA) Inc. CUSTOMER SATISFACTION DEPARTMENT 340 Ferrier Street Unit 2 Markham, Ontario ... set the dial and leave it comfortably and clearly, without distortion. ! Do not use , please read and observe WARNINGs and CAUTIONs in Canada http://www.pioneerelectronics.ca 1 Register...
Owner's Manual - Page 3
...the connections of the power supply and speakers if the fuse of the car stereo while the en- Electrical shock could result in overheating and smoke, damage to the amplifier is for vehicles ...cause cancer and birth defect or other governmental entities to prevent equipment malfunction.
Do not use of the separately sold with the product may exhaust the battery. Before you have removed...
Owner's Manual - Page 4
... control) switch
You can remain unchanged and to prevent malfunction of the gain control. To adjust the switch, use with an RCA equipped Pioneer car stereo, with an RCA equipped car stereo (standard output of 500 mV), set amplifier gain control to a level appropriate for a few seconds as a normal function, but output is turned down.
! Protective function...
Owner's Manual - Page 5
... 5 Signal waveform when outputting at high volume using amplifier gain control
Signal waveform distorted with little increase in power.
Setting the unit
Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this will simply increase distortion, with high output, if you raise the gain of the amplifier the power changes only slightly.
Owner's Manual - Page 6
... as possible from the speaker wires. Install and route the separately sold separately) Connect male terminal of this wire to Connections when using the speaker input wire on or off, which may malfunction. !
If the system remote control wire of the car stereo.
Refer to the system remote control terminal of the amplifier is limited.
Owner's Manual - Page 7
...Mono)
En 7 For other bridge connection.
Connecting the units About bridged mode
Other than subwoofer
Speaker channel Two-channel output One-channel output
Power
MAX input: Min. 250 W
MAX input: Min. 800 W
English
Section
03
Speaker impedance is a risk of fire, smoke or damage. Improper connection to the amplifier may result in parallel, Left + and Right * (Diagram A) or use a single...
Owner's Manual - Page 8
... wire
4 Connect the wires to the amplifier using the supplied speaker input wire. ! Twist
Connecting the power terminal
The use of overheating, malfunction and injury, including minor burns.
1 Route battery wire from engine compartment to wires. Section
03 Connecting the units
Connections when using the speaker input wire
Connect the car stereo speaker output wires to the terminal. Do...
Owner's Manual - Page 9
... to the speaker output terminals.
Connecting the units
Section
03
English
1 System remote control terminal 2 Ground terminal 3 Power terminal 4 Terminal screws 5 Battery wire 6 Ground wire 7 System remote control wire
Connecting the speaker output terminals
1 Use wire cutters or a utility knife to strip the end of wire and then twist the wire. Fix...
Owner's Manual - Page 10
... supplied are behind the panel and protect all cables and important equipment (e. When drilling to install the amplifier, always confirm no parts are used, they make temporary connections and check to installation in front of the car, which can be easily removed. fuel/brake lines, wiring) from being cut by vibration of the...
Owner's Manual - Page 11
... when working out total current drawn by multiple power amplifiers. Use this unit when an audio signal is nearly the maxi- Specifications and the design are subject to 26 V Maximum input level / impedance: RCA 6.5 V / 22 kW Speaker 26 V / 22 kW
CEA2006 Specifications
Power output 125 W RMS × 2 Channels (at 14.4 V, 4 W and ≦ 1 % THD+N)
S/N ratio 78 dBA...
Owner's Manual - Page 40
... (USA) INC. P.O. Printed in China Imprimé en Chine
UC TEL: (800) 421-1404
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique TEL: (0) 3/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270 407號8 02...
Similar Questions
My Pioneer Gm-5500t Audio Inputs Are Not Working Help
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
(Posted by jddubray 4 years ago)
Powering Up A Gm-a5602 Amp
The amp and Subs were working fine for a couple of months and then one day the blue power light woul...
The amp and Subs were working fine for a couple of months and then one day the blue power light woul...
(Posted by Mayojd74 6 years ago)
Gm-5500t 820 Watt Amp....not Turning On Even With Everything Connected Properly?
(Posted by coolmikepwnsu 12 years ago)