Pioneer GM-5500T Support Question
Pioneer GM-5500T Support Question
Find answers below for this question about Pioneer GM-5500T.Need a Pioneer GM-5500T manual? We have 1 online manual for this item!
Question posted by tyeager01 on September 3rd, 2011
Gm-5500t Shutting Down At High Volume
What is causing my Amp to Shut off at a high volume?
Current Answers
Related Pioneer GM-5500T Manual Pages
Owner's Manual - Page 2
...Register your hearing adapts. CUSTOMER SUPPORT DIVISION P.O.
The Safety of your hearing. Set your volume control at a safe level-a level that lets the sound come through this manual before...-1404 CANADA Pioneer Electronics of your sensitive hearing. Do not turn up the volume so high that you read through clearly without affecting your equipment by setting your equipment at...
Owner's Manual - Page 3
... wire to hear
outside sounds. ! Always keep the volume low enough to the car body.
! Extended use of any attached speakers may exhaust the battery. If the temperature inside the amplifier gets too
high. !
Also, damage to this occurs, switch the system power off , and the amplifier will operate in the conditions outlined below and...
Owner's Manual - Page 4
... with the head unit at a high volume, set amplifier gain control to a level appropriate for a few seconds as a normal function, but output is restored when the volume of the head unit is connected:... for the preout maximum output level of the head unit, so that of the car stereo output. ! When outputting high volume sound etc., this unit
Preout level: 2 V (Standard: 500 mV)
Above illustration shows...
Owner's Manual - Page 5
... when outputting at high volume using amplifier gain control
Signal waveform distorted with little increase in power. English
Section
02
En 5
Setting the unit
Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this will simply increase distortion, with high output, if you raise the gain of the amplifier the power...
Owner's Manual - Page 6
... from the speaker wires.
Install and route the separately sold battery wire, ground wire, speaker wires and the amplifier as far away as possible from the antenna, antenna cable and tuner.
6 En If the car stereo lacks a system remote control terminal, connect the male terminal to Connections when using the speaker input wire...
Owner's Manual - Page 7
... is a risk of fire, smoke or damage. For bridged mode for monaural and other amplifiers, please follow the speaker output connection diagram for bridging shown on rear: two 8 W ...be two-channel (stereo) or one-channel (mono). For other bridge connection. Improper connection to the amplifier may result in malfunction or personal injury due to 8 W for a two-channel amplifier, with a 4 ...
Owner's Manual - Page 8
.... Use pliers, etc., to crimp lugs to wire ends. Section
03 Connecting the units
Connections when using the speaker input wire
Connect the car stereo speaker output wires to the amplifier using the terminal screws, there is a risk of overheating, malfunction and injury, including minor burns.
1 Route battery wire from engine compartment to...
Owner's Manual - Page 10
... installation holes are to shut down until it could injure the driver or
passengers if the vehicle stops suddenly. - Example of installation on the car model. To ensure proper installation, use under high-volume conditions, etc. Places where it may interfere with the use of the amplifier, or become loose causing the amplifier to be located. 2 Drill...
Owner's Manual - Page 11
... the maxi- The average current drawn is input.
En 11
mum current drawn by this value when working out total current drawn by multiple power amplifiers. Specifications and the design are subject to 26 V Maximum input level / impedance: RCA 6.5 V / 22 kW Speaker 26 V / 22 kW
CEA2006 Specifications
Power output 125 W RMS...
Similar Questions
My Pioneer Gm-5500t Audio Inputs Are Not Working Help
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
My amplifier inputs are not working because I screwed up and took it apart to clean the inputs becau...
(Posted by jddubray 4 years ago)
Gm-5500t 820 Watt Amp....not Turning On Even With Everything Connected Properly?
(Posted by coolmikepwnsu 12 years ago)