Pfaff select 1530 Support Question
Pfaff select 1530 Support Question
Find answers below for this question about Pfaff select 1530.Need a Pfaff select 1530 manual? We have 1 online manual for this item!
Question posted by gveer02 on April 5th, 2014
Timing Procedure
What is needle bar height and where is hook point for timing?
Current Answers
Related Pfaff select 1530 Manual Pages
Owner's Manual - Page 3
... 16 Base plate 17 IDT System / Integrated Dual Feed (1540/1530) 18 Needle holder with fixing screw 19 Presser foot lifter 20 Button for "reverse sewing" 21 Stitch length dial 22 Stitch selection 1540 23 Carrying handle 24 Stitch selection 1530 & 1520 25 Thread guide 26 Sewing lamp (max. 15 watt) 27 Stitch width dial 28...
Owner's Manual - Page 12
... speed
For this plug is switched on the front part of electric shock, this sewing machine, a foot controller typ AW 0253 or AE 013 must to use. To reduce the risk of the foot control. Operate your Pfaff select
Carrying-case Place the cords, foot control and instruction book in a polarized outlet only...
Owner's Manual - Page 13
... also used as an extended work support. The enclosed accessories are numbered. When replacing the removable accessory tray to sew with the free arm of the sewing machine.
3 Operate your Pfaff select Accessory tray Your Pfaff select sewing machine has a removable accessory tray (15) which is flush with the free arm, you must remove the accessory...
Owner's Manual - Page 23
... presser foot Turn off the main switch Position the needle at its highest point Press the presser foot upwards at the front and downwards at the back at the same time so that it disengages from the presser foot holder ...is properly engaged by raising the presser foot lifter.
13 Operate your Pfaff select Presser foot lifter The presser foot is raised or lowered with the presser foot lifter (19).
Owner's Manual - Page 24
... out to the rear, and let it snaps into place. The fabric is done in industrial sewing machines.
Operate your Pfaff select The Intigrated dual feed/IDT System (Models 1530 and 1540) PFAFF offers the ideal solution for sewing difficult materials: the intigrated dual feed. Disengaging the Intigrated Dual Feed Hold the dual...
Owner's Manual - Page 25
... as far as it goes. The normal setting for sewing is dropped. A
15
To do this, open the bobbin case/hook cover and move the needle to its highest
point. Now loosen the fixing screw
A
(18) and pull the needle downwards.
Operate your Pfaff select
Changing the needle Switch off the main switch
To remove: Lower...
Owner's Manual - Page 32
....
1540 1530 1520
stitch Stitch number
Stitch width in mm
Stitch length in mm
Dual feed on or off =
Thread tension Presser foot number
22 stitch
Utility stitches and practical sewing Explanation of the needle thread tension and whether the sewing is carried out with further instructions that are necessary when sewing the selected stitches. These...
Owner's Manual - Page 35
... so that the crease line runs along edge guide B.
• Using the needle positioning knob 28,
select the needle position to regulate the penetration of presser foot 3. Remember!
Stitch D (1540), stitch H (1530/1520)
25
sewing by hand is no longer necessary.
• Serge the edge of the hem
• Fold the edge inwards by the...
Owner's Manual - Page 39
... knits. Utility stitches and practical sewing
stitch stitch
1540 I 1530 K 1520 K
5- Stretch
3-5 0/3 3-5 0/3 3-5 0/3
Closed overlock stitch The closed overlock stitch is perfect for open-knit fabrics. When overlocking, if you select a needle
position other than center,
and stitch
width other than 5 , make sure the needle
does not strike the bar of the needle, not to add a woolen thread...
Owner's Manual - Page 43
... the front. • Clamp the threads to the required length.
Use the center needle position
.
A
B
Carfully cut the threads. Clip the top thread after a few stitches.
• Select stitch B and sew a few bartacks while holding the fabric securely.
• Select stitch D. Sew the left and right of the gimp thread into the buttonhole and cut...
Owner's Manual - Page 47
...and practical sewing
E
stitch
F
1540 G 0 - 1530 E 0 -
2-3 6 2-3 Optional
1520 E 0 -
2-3 Optional
G
Darning with a small curve. When doing this, the guide fork G should position itself around the presser bar. This ... sewing the damaged area, rotate the fabric again.
Set the needle at its highest point and push the pin of the darning foot fully into the hole C of the
sewing machine...
Owner's Manual - Page 52
... stitches.
• Leave the needle in the fabric, raise the presser foot and insert the fabric into the hemmer foot scroll.
• Lower the presser foot and guide the fabric evenly into the hemmer.
Utility stitches and practical sewing
stitch
1540 G 0 3 1530 E 0 3 1520 E 0 3
3-5 7 3-5 Optional 3-5 Optional
Stabilizing edges With the hemmer you can hem...
Owner's Manual - Page 59
.../Tapering Tapering is easy with your select sewing machine.
Uneven embroidering • Place stabilizer under the fabric.
• Set needle thread tension to "buttonhole", select zigzag stitch G (1540), E (1530/ 1520), set stitch length to 0 while sewing at a constant speed through the procedure. Note: If you selected the right or left needle position, the stitch width will only...
Owner's Manual - Page 60
Adjust the stitch
width with the width dial (34) during sewing of a flower motif with 45 degree angles.
• Set needle thread tension to "buttonhole", zigzag stitch G (1540), E (1530/1520), set stitch length to "buttonhole".
• Flowers:
Select center needle position
and
embroider individual petals. If the corner is to continue in combination with the...
Owner's Manual - Page 61
... tension is set to "buttonhole".
• Select the right needle position and sew over both buttonhole seams.
Appliqué Appliqués are pointed at the ends, you to appliqué.
• Insert the appliqué foot in the "buttonhole" area. You can have to 10 mm.
• Sew two buttonhole seams about 1 mm apart using...
Owner's Manual - Page 62
... an eyelet plate (special accessory). The stitches should be hollow.
Set the presser bar lifter at the front.
• Place the marked fabric taut in the eyelet plate.
... the selected stitch. For classic eyelet embroidery, use stitch G (1540), E (1530/1520), with your sewing machine.
• Using a magic marker, draw your one or two of the needle plate. Decorative sewing and embroidery...
Owner's Manual - Page 63
...(select 1540) to add a decorative touch.
These squares will then be realized in patterns to form the top layer of the quilt. The distance of the needle to... bottom quilt layer.
• Use your select sewing machine. Decorative sewing and embroidery techniques
Patchwork quilt
Patchwork and quilting are joined together in a much shorter time with a layer of batting sandwiched between....
Owner's Manual - Page 70
... sewing and produces a moredefined pintuck. Accessories and needles
stitch
1540 G 0 2,5 1530 E 0 2,5 1520 E 0 2,5
5 Shirring 5 foot
5
Pintuck foot This classic heirloom sewing ...needle plate and the sewing machine provides space for heavier materials use the pintuck foot with a twin needle (e.g. 130/705 H-ZWI; 1.6 or 2.0 mm needle spacing; size 80).
• Thread the two needles...
Owner's Manual - Page 79
... lamp fully into its socket as far as a special accessory) will go. • At the same time, turn the lamp a half
turn it clockwise so that both stops of the sewing machine
Removal: • Hold the sewing machine tightly. • Push the lamp into the socket and turn anti-clockwise and remove it is 15...
Owner's Manual - Page 80
...: Before you replace sewing feet or needles, you leave the machine, even for thread. If you must switch off Needle is bent, and has hit the needle plate because you insert the bobbin case, push it . Use a needle system 130/705 H.
Use needle with brush. The wrong needle is inserted Needle is too small for a short time, do not forget...
Similar Questions
Edge Guide - Pfaff Select 1540 Sewing Machine
How does the Edge Guide work for the Pfaff Select 1540 sewing machine?
How does the Edge Guide work for the Pfaff Select 1540 sewing machine?
(Posted by jesjames 2 years ago)
The Sewing Machine Will Say Calibrate Embroidery Unit. I Click The Check Mark T
when I click on calibrate the sewing machine goes into thinking mode & it just does it for a long ti...
when I click on calibrate the sewing machine goes into thinking mode & it just does it for a long ti...
(Posted by Anonymous-156748 8 years ago)
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
What Is Needle Bar Height And Where Is Hook Point For Timing?
(Posted by gveer02 10 years ago)
Sewing Machine Is Blinking Away And Not Able To Operate
Sewing machine was sewing constantly even after I removed my foot from the pedal. I had to switch it...
Sewing machine was sewing constantly even after I removed my foot from the pedal. I had to switch it...
(Posted by kasperflindt 11 years ago)