Panasonic EY7880 Support Question
Panasonic EY7880 Support Question
Find answers below for this question about Panasonic EY7880 - 28.8V ROTARY HAMMER.Need a Panasonic EY7880 manual? We have 1 online manual for this item!
Question posted by neilcooper2000 on October 28th, 2013
Ey7880 Drill
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would cause this please
Current Answers
Related Panasonic EY7880 Manual Pages
EY7880 User Guide - Page 3
...can cause you are connected and properly used for outdoor use common sense when operating a power tool. Damaged or entangled cords increase the risk of electric shock.
5) When operating a power tool ... or unplugging the power tool. This enables better control of flammable liquids, gases or dust. Keep your body is in the off position before turning the power tool on. GENERAL SAFETY RULES...
EY7880 User Guide - Page 4
.... 2) Do not use the power tool if the switch does not turn the trigger switch off . Check for which can damage the battery pack or motor. Use of any other battery packs may cause irritation or burns.
Service
1) Have your power tool serviced by poorly maintained power tools. 6) Keep cutting tools sharp and clean.
job better...
EY7880 User Guide - Page 5
... the Forward/Reverse lever to the center position (switch lock).
8) Do not strain the tool by holding the speed control trigger halfway (speed control mode) so that the motor stops.
6) Do not operate the Forward/Reverse lever when the trigger switch is located so that it will not be stepped on, tripped...
EY7880 User Guide - Page 6
... Never carry charger by the manufacturer, because special purpose tools are the same number, size and shape as specified below. A battery short can cause a large current flow, over heating and burns.
24.... If it to disassemble the battery pack housing.
15) Do not store the tool and battery pack in locations where the temperature may result in good electrical condition. Do...
EY7880 User Guide - Page 7
... use . To mount the bit 1-1. Insert a bit into the mounting hole,
and turn it goes. To dismount the bit 2-1. Forward
Reverse
Be sure to set the switch ... by proceeding two steps for bit Grease the oval indentation on the body of the tool and the battery pack, ( ) and insert the battery pack. ( ) •...pack is completely stopped.
. Make sure that the bit is not inserted firmly.
2.
EY7880 User Guide - Page 8
... injury or damage if it is completely stopped. Shoulder pad - 8 - There are four modes available with the combination of switching lever
Speed/Blow Mode selection lever
Hard blow hammering mode
Recommended application
This mode has hard blow hammering which is suitable for wood drill with high
torque.
Concrete drill
Support handle
Place the support handle...
EY7880 User Guide - Page 9
... into "Class 1 LED Product" to the main unit of the tool. This product is designed to cool thoroughly (at least 30 minutes). Control...causes the overheating protection feature to another. Battery pack
For Appropriate Use of procedures other situations
where the temperature is active.
• If the overheating protection feature activates, allow the driver to illu- The rotary hammer...
EY7880 User Guide - Page 10
...pack (below -10°C (14°F), charging will automatically stop to prevent degradation of the battery charger contaminated, be affected ... notice the terminals of battery. The life of the tool, replace the battery pack cover immediately in use ....: Your battery pack is removed from contaminating the battery terminals and causing a short circuit.
Alignment marks
- 10 - • When ...
EY7880 User Guide - Page 13
... the shape of the support handle.
Pass the drill bit through dust collection cup.
* Do not use the tool for cutting other than concrete, mortar and other volatile...your local service center.
Install a dril bit. 2. Dust Collection Cup •EY9X004E Drill chuck •EY9HX400E Hammer chuck •EY9HX401E Chisel Attachment •EY9HX402E If you need any assistance for wiping...
EY7880 User Guide - Page 14
...to blow in hammering mode. SPECIFICATIONS
MAIN UNIT
Concrete
20 mm (25/32")
Maximum Drilling Diameter Steel
13 mm (33/64")
Wood
27 mm (1-1/16")
Motor Voltage
28.8 V DC...approximately 30 seconds and repeat this should happen, operating hammering mode with enough force when working.
2. Press down on the bit to engage the hammer and cause it to press down with no load. If this ...
EY7880 User Guide - Page 15
... min. EY9210 90 min.
- 15 -
EY9201 EY9231 55 min.
NOTE: This chart may include models that are not available in your area.
Full: 50 min.
28.8 V EY9L80 Usable: 55 min.
EY9200 EY9230 45 min. Please refer to the latest general catalogue.
24 V
EY9116 EY9117 60 min.
Similar Questions
Pnasonic Battery Terminal Wiring
Panasonic EY7540 impact driver. Where are the four wires connecting to the battery terminal block co...
Panasonic EY7540 impact driver. Where are the four wires connecting to the battery terminal block co...
(Posted by groffee 8 years ago)
Image Transmission Tool
Hi,To whomit may concern How to get image transmission tool for panasonic Av-HS300
Hi,To whomit may concern How to get image transmission tool for panasonic Av-HS300
(Posted by mansoormoslemi 10 years ago)
Looking For Ey5917 Case
I would like to replace the carrying case for the 18V Panasonic Drill and Driver.
I would like to replace the carrying case for the 18V Panasonic Drill and Driver.
(Posted by jpkoiman 11 years ago)
Replacement Battery
Where can I buy a replacement battery for the EY6105 cordless drill?
Where can I buy a replacement battery for the EY6105 cordless drill?
(Posted by pgelfan 12 years ago)
Panasonicey7440
my cordless drill is about 3years old it is starting to act up a bit by when i am screwing screws it...
my cordless drill is about 3years old it is starting to act up a bit by when i am screwing screws it...
(Posted by peaderdoyle 13 years ago)