Panasonic EY6950 Support Question
Panasonic EY6950 Support Question
Find answers below for this question about Panasonic EY6950 - 18V HAM. DRILL&DRIVE.Need a Panasonic EY6950 manual? We have 1 online manual for this item!
Question posted by jpkoiman on September 15th, 2012
Looking For Ey5917 Case
I would like to replace the carrying case for the 18V Panasonic Drill and Driver.
Current Answers
Related Panasonic EY6950 Manual Pages
EY6950 User Guide - Page 1
Read manual completely before first using this product and save this manual for future use. Cordless Hammer Drill Driver
Operating Instructions Model No: EY6950
IMPORTANT
This manual contains safety information.
EY6950 User Guide - Page 2
...switch is beneath, or on the other side of the area when you are working. Carrying tools with the switch on invites accidents.
9) Remove adjusting keys or wrenches before inserting battery ... battery pack. A charger that may be used with another battery.
5) Use battery operated tool only with the specified charger for your application. Use of fire. READ AND UNDERSTAND ALL ...
EY6950 User Guide - Page 3
...servicing a tool, use only identical replacement parts. If damaged, have to control.
19) Check for your model. The battery will make a connection from tool or place the switch in a risk of this tool is ...tools sharp and clean.
Service or maintenance performed by qualified repair personnel. Use reverse motion to loosen jammed bits.
6) When storing or carrying the tool...
EY6950 User Guide - Page 4
... Pack
shown below .
- 4 - that wire size is large enough for ampere rating of damaging the electric plug and cord, pull by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other masonry products * Arsenic and chromium from...
EY6950 User Guide - Page 5
... qualified electrician to install the proper outlet. This is required. If it must only be replaced by a repair shop appointed by cord or yank it to persons.
23) Do not ...10) Do not disassemble charger; take it to work together. Never carry charger by the manufacturer, because special purpose tools are specifically designed to a qualified serviceman when service or repair is...
EY6950 User Guide - Page 6
...: If excessive play occurs in the chuck, secure the drill in the center position (switch lock). Turn the Lock collar counterclockwise (looking from the front).
2. This tool is equipped with a screwdriver by unscrewing the Lock collar and tighten the screw (left-handed screw) with a keyless drill chuck.
1. Removal Slide the Lock collar to tighten...
EY6950 User Guide - Page 7
...- The speed increases with the amount of depression of the trigger for efficient tightening of screws and drilling. When beginning work, depress the trigger slightly to a complete stop.
Forward/Reverse lever Operation
CAUTION...rotation, set the lever to start the tool slowly.
3. It snaps into place to give a strong torque even in the storage case.
. A feedback electronic controller is ...
EY6950 User Guide - Page 8
...the trigger switch not engaged and a screwdriver bit locked in -lbs).
Tool needs cool off time before use . Do not close up to ...as a manual screwdriver (up vent holes on body sides of the driver (position on the speed control trigger. Speed Selection
Choose a low...low speed when strong force is handy for tightening screws that case, charge the battery until charging is applied may cause a...
EY6950 User Guide - Page 9
extremely short after recharging, replace the battery pack with a new one hour to warm up the battery to the level of the ...will automatically be lit. Otherwise battery pack may be produced when the plug is inserted into the AC power supply, but this case, charging takes longer to fully charge the battery pack, than two battery packs consecutively. Cool down . If the charging lamp...
EY6950 User Guide - Page 10
... of the battery pack.
. MAINTENANCE
Use only a dry, soft cloth for size of drill's chuck. ACCESSORIES
Use only bits suitable for wiping the unit. Do not use a damp cloth,... thinner, benzine, or other volatile solvents for the job.
EY6950
MATERIAL/ MORTAR /
CONDITION
BRICK
DRILLING
WOOD / YELLOW PINE
Thickness: 40 mm (1-37/64") or less
METAL METAL HOLE SAW
...
EY6950 User Guide - Page 11
...
2.0Ah
EY9168(H)
EY0110
See the name plate on the bottom of the charger.
9.6 V
12V
15.6V
18V
EY9080(D) EY9086B(C)
EY9006B(C)
20min. SPECIFICATIONS
MAIN UNIT
Model
Screw driving
Machine screw Wood screw Masonry screw
Capability
Mortar/Brick
Drilling
Wood Metal
Metal hole saw
Motor
No load speed
LOW HIGH
Blows rate per LOW
minute...
EY6950 User Guide - Page 12
...to the place of purchase with a dated proof of purchase, in Japan PANASONIC CONSUMER ELECTRONICS COMPANY
One Panasonic Way, Secaucus, New Jersey 07094
EY981069501 H1507
Printed in the original packaging... of any power tool voids the guarantee. 30-DAY QUALITY SATISFACTION GUARANTEE:
If you are dissatisfied with any Panasonic Cordless Power Tool for a full refund, or call Panasonic at 201-392-...
Similar Questions
Looking For
is there any where to still buy the panasonic ey3654 7.2v caulking gun
is there any where to still buy the panasonic ey3654 7.2v caulking gun
(Posted by filthyno1 7 years ago)
Pnasonic Battery Terminal Wiring
Panasonic EY7540 impact driver. Where are the four wires connecting to the battery terminal block co...
Panasonic EY7540 impact driver. Where are the four wires connecting to the battery terminal block co...
(Posted by groffee 8 years ago)
Ey7880 Drill
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would c...
hi there i have a ey7880 that has stopped hammering it just turns do you have any ideas what would c...
(Posted by neilcooper2000 10 years ago)
Impact Power Mode Lights Flashing When Trigger Pressed ?
i recently dropped my impact driver ey7540 and snapped in two i bought the casing and the ribbon cab...
i recently dropped my impact driver ey7540 and snapped in two i bought the casing and the ribbon cab...
(Posted by machibees5 12 years ago)
I Am Looking For A Floppy Disk Drive Part # Ju257a166p.
My roland keyboard uses this 1.44 Mb Floppy Disk Drive but it has ceased working. I would like your ...
My roland keyboard uses this 1.44 Mb Floppy Disk Drive but it has ceased working. I would like your ...
(Posted by gkiap98 14 years ago)